Circuit Description
The body control module (BCM) uses the ambient light sensor signal to control the automatic headlamp control system and the daytime running lamps (DRL). The ambient light sensor is connected directly to the BCM through the DRL ambient light sensor signal circuit and the DRL ambient light low reference circuit.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC B2647 Ambient Light Sensor Circuit Low
Conditions for Running the DTC
The DRL feature or the automatic headlamp control feature must be enabled.
Conditions for Setting the DTC
| • | The BCM detects a short to ground in the DRL ambient light sensor signal circuit. |
| • | The ambient light sensor is internally shorted. |
| • | The condition above must be present for more than 0.3 seconds. |
Action Taken When the DTC Sets
| • | The BCM stores DTC B2647 in memory. |
| • | The DRL will default to low light mode and the headlamps, park lamps, tail lamps and side marker lamps will illuminate. |
Conditions for Clearing the DTC
| • | The BCM no longer detects a short to ground in the DRL ambient light sensor signal circuit. |
| • | A history DTC B2647 will clear after 100 consecutive ignition cycles if the condition for the malfunction is no longer present. |
| • | The BCM receives a clear code command from the scan tool. |
Diagnostic Aids
| • | If the DTC B2647 is a history DTC, the fault may be intermittent. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems. |
| • | The following conditions may cause an intermittent malfunction to occur: |
| - | An intermittent short to ground in the DRL ambient light sensor signal circuit |
| - | The ambient light sensor is intermittently shorted. |
| - | The BCM is intermittently shorted to ground. |
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
Schematic Reference: Exterior Lights Schematics Connector End View Reference: Master Electrical Component List in Wiring Systems | ||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information |
2 |
Does the scan tool indicate that the ambient light sensor input parameter is within the specified range? | 0.25-2.5 V | Go to Diagnostic Aids | Go to Step 3 |
3 |
Does the scan tool indicate that the ambient light sensor input parameter is greater than the specified value? | 2.5 V | Go to Step 4 | Go to Step 5 |
4 |
Does the scan tool indicate that the ambient light sensor input parameter is less than the specified value? | 0.25 V | Go to Step 8 | Go to Step 6 |
5 | Test the DRL ambient light sensor signal circuit of the ambient light sensor for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 9 |
6 | Test the DRL ambient light sensor low reference circuit of the ambient light sensor for a high resistance, an open, or short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 7 |
7 | Test the DRL ambient light sensor signal circuit of the ambient light sensor for a short to battery positive voltage, a high resistance, or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 9 |
8 | Inspect for poor connections at the harness connector of the ambient light sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 10 |
9 | Inspect for poor connections at the harness connector of the BCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 11 |
10 | Replace the ambient light sensor. Refer to Daytime Running Lamp (DRL) Ambient Light Sensor Replacement . Did you complete the replacement? | -- | Go to Step 12 | -- |
11 | Replace the BCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup and programming. Did you complete the replacement? | -- | Go to Step 12 | -- |
12 |
Does the DTC reset? | -- | Go to Step 2 | System OK |
