MANUAL UPDATE-SEC.8A A/C BLOWER CONTROLS C68

MODELS AFFECTED: 1989 ELECTRA AND LESABRE ESTATE WAGONS WITH C68 AIR CONDITIONING

SERVICE MANUAL UPDATE

Update pages 8A 66-0 through 5 and 8A 67-0 through 5 of the 1989 Electra/LeSabre Wagon Service Manual to reflect the change to the Delco Electronics Power Interface Module for the C68 system. (corrected pages (12) attached)

AIR CONDITIONING: BLOWER CONTROLS

COMPONENT LOCATION

A/C Pressure Cycling Switch....RH rear of engine compartment, 201-7-E on accumulator Blower Control Module..........RH front of dash on plenum 201-12-A Blower Interface Module....... RH front of dash, on plenum Blower Motor...................RH front of dash 201-17-A Fuse Block.....................Behind LH side of I/P, near shroud 201-4-A C250 (2 cavities)..............I/P harness, behind center of I/P 201-7-A C436 (4 cavities) . . . . . . .Engine compartment, near rear 201-6-C of RH valve cover C999 (8 cavities) . . . . . . .RH front of dash, on plenum G103 . . . . . . . . . . . . . A/C harness, RH rear of engine 201-12-A compartment behind accumulator G130 . . . . . . . . . . . . . Below RH side of I/P,left of grommet 201-1-B S100...........................A/C harness, RH rear of engine 201-12-A compartment behind accumulator S283...........................I/P harness, above RH side of radio 201-10-B S289...........................I/P harness, above RH side of radio 201-10-B S806...........................A/C harness, near Blower Motor 201-7-E

AIR CONDITIONING: BLOWER CONTROLS

TROUBLESHOOTING HINTS

Try the following checks before doing the System Diagnosis.

1. Check A/C Fuse and CIG-CLK Fuse by visual inspection.

2. Check that grounds G103 and G130 are clean and tight.

3. Check that Blower Motor connectors are mated correctly and firmly seated.

4. Check Fusible Link A by operating the Horn.

Go to the A/C System Check in Section 8A-62 for a guide to normal operation.

Go to System Diagnosis for diagnostic tests.

SYSTEM DIAGNOSIS

Do the tests listed for your symptom in the Symptom Table below.

SYMPTOM TABLE

SYMPTOM DO TEST ------- ------- Heater and A/C A: Heater and A/C Control Assembly Control Assembly does not operate at Voltage Test all (no display)

Blower will not run C: Blower Control in any mode Module Test

Blower runs at high Check PPL wire speed only with igni- from Blower Inter- tion in RUN. No low face Module to Con- speed or auto blower nector C999 for an open. If wire is ok, replace Blower Inter- face Module

Heater and A/C B: Panel Illumin- Control Assembly ation Test panel illumination does not light

A: HEATER AND A/C CONTROL ASSEMBLY VOLTAGE TEST

Measure: VOLTAGE

AT: HEATER AND A/C CONTROL ASSEMBLY CONNECTORS C1 & C2

(Disconnected) Conditions

Ignition Switch: RUN

Measure Correct For Between Voltage Diagnosis -------- ------- ---------- C1/B (BRN/ WHT) & Battery See 1 Ground

C3/B (ORN) Battery See 2 &Ground

C3/B(ORN) Battery See 3 & C2/D (BLK)

C3/B (ORN) Battery See 3 & C2/E (BLK)

If all voltages are correct, replace the Heater and A/C Control Assembly

1. Check/repair BRN/WHT and BRN (50) wire for an open or short to ground

2. Check/repair ORN (40) wire for an open or short to ground

3. Check/repair BLK (150) wire for an open

B: PANEL ILLUMINATION TEST

Measure: VOLTAGE

AT: HEATER AND A/C CONTROL ASSEMBLY CONNECTOR C3,

(Disconnected)

Conditions Light Switch: PARK Dimmer Switch: FULL BRIGHTNESS

Measure Correct For Between Voltage Diagnosis ------- ------- --------- C3/D (GRY) Battery See 1 & Ground

If voltage is correct, replace Heater and A/C Control Assembly

1. Check/repair GRY (8) wire for an open

AIR CONDITIONING: BLOWER CONTROLS

C: BLOWER CONTROL MODULE TEST

(TABLE 1)

Measure: VOLTAGE

AT: BLOWER CONTROL MODULE CONNECTORS C1 & C2

(Disconnected) Conditions

Ignition Switch: RUN Blower: Hi

Measure Correct For Between Voltage Diagnosis ------- ------- --------- C1/B (RED) Battery See 1 &Ground

C1/B (RED) Battery See 2 & C2/C (BLK)

C2/B (GRY) Battery See 3 &Ground

If all voltages are correct, go to Table 2

1. Check/repair RED (2) wire and Fusible Link A for an open or short to ground

2. Check/repair BLK (151) wire for an open

3. Go to Test E: Blower Interface Test

C: BLOWER CONTROL MODULE TEST (TABLE 2)

Connect: FUSED JUMPER

AT: BLOWER CONTROL MODULE CONNECTORS C1 & C2

(Disconnected)

Connect Correct For Between Result Diagnosis ------- ------ ---------- C1/B (RED) Blower See 1 & C2/A (PPL) Motor runs

If result is correct, replace Blower Control Module

1. Go to Test D: Blower Motor Test

D: BLOWER MOTOR TEST

Measure: VOLTAGE

AT: BLOWER MOTOR CONNECTORS

(Connected)

Conditions:

Ignition Switch: RUN Blower: Hi

Measure Correct For Between Voltage Diagnosis ------- ------- --------- C1 (PPL) Battery See 1 &Ground

C1 (PPL) Battery See 2 & C2 (BLK)

If all voltages are correct, replace Blower Motor

1. Check/repair PPL (65) wire for an open or short to ground

2. Check/repair BLK (151) wire for an open

AIR CONDITIONING: BLOWER CONTROLS

E: BLOWER INTERFACE TEST

Measure: VOLTAGE

AT: CONNECTOR C999 (Disconnected)

Conditions:

Ignition Switch: RUN Blower: Hi

Measure Correct For Between Voltage Diagnosis ------- ------- --------- Y4 (BRN) Battery See 1 &Ground

X1 (GRN/ BLK)& Battery See 2 Ground

If all voltages are correct, check Blower Interface Module pigtail harness for damage. If harness is ok, replace Blower Interface Module

1. Check/repair BRN (50) wire for an open or short to ground. If wire is ok, replace Heater and A/C Control Assembly

2. Check/repair GRN/BLK (900) wire for an open or short to ground. If wire is ok, replace Heater and A/C Control Assembly

CIRCUIT OPERATION

The speed of the blower motor is determined by the voltage applied to the motor. At low Blower Motor speeds, the applied voltage is about 4 volts. As the voltages increase, the Blower Motor speed increases until maximum blower speed is reached at about 12 volts.

Blower speed is determined by the Heater and A/C Control Assembly from temperature signal inputs and the operating mode of the system. The Heater and A/C Control Assembly accepts input requests from the driver via the front panel pushbuttons.

The blower speed request from the Heater and A/C Control Assembly is output at connector C2 terminal B. It is a continuously variable voltage proportional to requested blower speed. At low blower speed, the output is approximately 5 volts. At maximum blower speed, the output voltage is approximately 12 volts.

The Blower Interface Module conditions the output signal from the Heater and A/C Control Assembly. The conditioned signal is then applied to the Blower Control Module. An amplifier and driver circuit in the Blower Control Module supply a voltage of between 4 and 12 volts to the Blower Mowr according to the input signal received from the Blower Interface Module.

The voltage applied at the Blower Motor is also fed back to the Blower Interface Module allowing precise speed control of the Blower Motor.

AIR CONDITIONING: COMPRESSOR CONTROLS

COMPONENT LOCATION Page-Figure ------------------ ----------- A/C Compressor Clutch . .. . ... . . RH front of engine, on A/C compressor A/C Compressor Clutch Diode . . . . Taped inside compressor clutch connector A/C Compressor Control Relay ........RH front of dash, on plenum

A/C Pressure Cycling Switch..........RH rear of engine compartment, 201-7-E on accumulator Blower Control Module ...............RH front of dash on plenum Blower Interface Module..............RH front of dash, on plenum Electronic Control Module (ECM)......Behind RH side of I/P, on 201-3-C A/C plenum Fuse Block...........................Behind LH side of I/P, near 201-4-A shroud C219 (1 cavity)......................Behind I/P, near heater and 201-6-B A/C control assembly C250 (2 cavities) .............I/P harness, behind center 201-7-A of I/P C436 (4 cavities) ..............Engine compartment, near 201-6-C rear of RH valve cover C858 (1 cavity) .....................Behind center of I/P,at rear of heater and A/C control assembly C907 (3 cavities)....................Rear of RH valve cover 201-6-C C999 (8 cavities) ...................RH front of dash, on plenum G103 ........................A/C harness, RH rear of engine 201-12-A compartment behind accumulator G251.................................Beside rear of RH valve cover 201-6-C S100.................................A/C harness, RH rear of engine 201-12-A compartment behind accumulator S110.................................Engine harness, LH rear of 201-0-C engine S283.................................I/P harness, above RH side of 201-10-B radio S289.................................I/P harness, above RH side of 201-10-B radio S999.................................Blower Interface harness, near 201-7-E A/C Compressor Control Relay

AIR CONDITIONING: COMPRESSOR CONTROLS ------------------------------------- TROUBLESHOOTING HINTS --------------------- Try the following checks before doing the System Check.

1. Check CIG-CLK Fuse and A/C Fuse by visual inspection.

Go to System Check for a guide to normal operation.

Go to System Diagnosis for diagnostic tests.

SYSTEM CHECK

Go to A/C System Check in Section 8A-62 for a guide to normal operation for the entire A/C System.

SYSTEM CHECK TABLE

ACTION NORMAL RESULT ------- ------------- 1. Turn Ignition A click can be heard Switch to RUN when Clutch engages and start engine Press AUTO and set temperature to 60 DEG

2. Alternately press Clutch plate move- AUTO and ECON ment can be seen on several times to the front of the verify that Clutch Compressor pulley, engages in AUTO If Clutch does not en- position gage, go to Step 5. If Clutch operates normally, continue to Step 3

3. Press AUTO to Engine coolant fan engage clutch runs when Compres- sor is engaged. Air moves freely through the condenser

4. Feel the suction If there is not a wide (cold) and output temperawre differ- (warm) pipes of ence after the Com- the Compressor pressor has run for several seconds, see Section 1B for Re- frigerant and Com- pressor diagnostics. If temperawre differ- ence exists, A/C Compressor and CompressorControls are operating nor- mally

5. Turn off Ignition If pressure is low, Switch and check refer to Section 1B refrigerant pres- for Refrigerant diag- sure according to nostics. according to If refrigerant pressure procedures in is normal, isorate Section 1B trouble conditions us- ing procedures in Sys- tem Diagnosis

SYSTEM DIAGNOSIS

Do the following tests if the A/C Compressor Clutch does not operate.

If other A/C functions, such as the Blower do not work, see 8A-66.

A: ISOLATION TEST ----------------- Connect: FUSED JUMPER

AT: A/C PRESSURE CYCLING SWITCH CONNECTOR (Disconnected)

Conditions:

Ignition Switch: RUN

Mode: AUTO

Set temperature: Below outside temperature

Jumper Correct For Between Result Diagnosis ------- ------ --------- A(BLK)& Compressor B(BRN) Clutch Seel engages

Check for low refrigerant pressure. See Section 1B of the Service Manual. If pressure is ok, replace A/C Pressure Cycling Switch

1. Go to Test B: A/C Compressor Control Relay test

AIR CONDITIONING: COMPRESSOR CONTROLS ------------------------------------- B: A/C COMPRESSOR CONTROL RELAY TEST (TABLE 1)

Measure: VOLTAGE

AT: A/C COMPRESSOR CONTROL RELAY CONNECTOR (Disconnected)

Conditions:

Ignition Switch: RUN Mode: AUTO Set temperature: Below outside temperature

Measure Correct For Between Voltage Diagnosis ------- ------- --------- E (BRN) Battery See 1 &Ground

D (WHT) Battery See 1 & Ground

D (WHT) & Battery See 2 F (LT BLU) I

If all voltages are correct, go to Table 2

1. Check/repair BRN and WHT (50) wire for an open or short to ground. If wire is ok, replace Heater and A/C Control Assembly

2. Go to Test D: Blower Control Module Test

B: A/C COMPRESSOR CONTROL RELAY TEST (TABLE 2)

Measure: FUSED JUMPER

AT: A/C COMPRESSOR CONTROL RELAY CONNECTOR (Disconnected)

Conditions:

Ignition Switch: RUN Mode: AUTO Set temperature: Below outside temperature

Jumper Correct For Between Result Diagnosis ------- ------ ---------- E(BRN)& Compressor A (LT GRN) Clutch See 1 engages

If all results are correct, replace A/C Compressor Control Relay

1. Reconnect A/C Compressor Control Relay and go to Test C: A/C Compres- sor Clutch Test

C: A/C COMPRESSOR CLUTCH TEST

Measure: VOLTAGE

AT: A/C COMPRESSOR CLUTCH CONNECTOR (Disconnected)

Conditions:

Ignition Switch: RUN Mode: AUTO Set temperature: Below outside temperature

Measure Correct For Between Voltage Diagnosis -------- ------- --------- B(LT GRN/BLK) Battery See 1 & Ground

B(LT GRN/BLK) Battery See 2 &A(BRN)

If all voltages are correct, replace A/C Compressor Clutch

1. Check/repair LT GRN/BLK (366) wire for an open

2. Check/repair BRN (257) wire for an open

AIR CONDITIONING: COMPRESSOR CONTROLS -------------------------------------- D: BLOWER CONTROL MODULE TEST

Measure: VOLTAGE AT: BLOWER CONTROL MODULE CONNECTORS C1 & C2 (Disconnected)

Conditions:

Ignition Switch: RUN Mode: AUTO Set temperature: Below outside temperature

Measure Correct For Between Voltage Diagnosis ------- -------- --------- C1/B (RED) Battery See 1 &Ground

C1/B (RED) &C2/C Battery See 2 (BLK) C2/D (YEL) Battery See 3 &Ground

C1/A (LT BLU) & Battery See 4 Ground

If all voltages are correct, replace Blower Control Module

1. Check/repair RED (2) wire and Fusible Link A for an open or short to ground

2. Check/repair BLK (151) wire for an open

3. Go to Test E. Blower Interface Module Test

4. Check LT BLU wire for an open (see schematic)

E: BLOWER INTERFACE MODULE TEST

Measure: VOLTAGE AT: CONNECTOR C999 (Disconnected) Conditions: Ignition Switch: RUN Mode: AUTO Set temperature: Below outside temperature

Measure Correct For Between Voltage Diagnosis ------- ------- --------- Y2 (PPL) O volts See 1 &Ground

Set temperature: 85 DEG F Mode: HEAT

Y2 (PPL) Approxi- & Ground mately 6 See 2 volts

If all voltages are correct, check Blower Interface Module pigtail harness for damage. If hamess is ok, replace Blower Interface Module

1. Check/repair PPL (966) wire for a short to battery. If wire is ok, replace Heater and A/C Control Assembly

2. Check/repair PPL (966) wire for an open or short to ground. If wire is ok, replace Heater and A/C Control Assembly

CIRCUIT OPERATION

The compressor for the air conditioning system is belt-driven by the engine through the A/C Compressor Clutch. The clutch allows the compressor to be disengaged when air conditioning is not required.

The Heater and A/C Control Assembly determines when the compressor clutch should be engaged. Operation of the compressor depends on the mode selected by the driver and, in the case of the AUTO mode, the set, in-car, and ambient temperawres.

When compressor operation is required, the Heater and A/C Control Assembly will signal the Blower Interface Module. The Blower Interface Module will then apply battery voltage to the Blower Control Module's compressor on input terminal (C2/D). When voltage is applied to the compressor on input terminal (C2/D), the Module will ground the A/C Compressor Control Relay coil. The relay will now energize and apply voltage to the A/C Compressor Clutch. The A/C Compressor Clutch will engage as long as refrigerant pressure is above 172 kPa (25 PSI) and below 310 kPa (45 PSI).

General Motors bulletins are intended for use by professional technicians, not a "do-it-yourselfer". They are written to inform those technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions and know-how to do a job properly and safely. If a condition is described, do not assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See a General Motors dealer servicing your brand of General Motors vehicle for information on whether your vehicle may benefit from the information.