GM Service Manual Online
For 1990-2009 cars only

Removal Procedure

Caution: When you are carrying an undeployed inflator module:

   • Do not carry the inflator module by the wires or connector on the inflator module
   • Make sure the bag opening points away from you
When you are storing an undeployed inflator module, make sure the bag opening points away from the surface on which the inflator module rests. When you are storing a steering column, do not rest the column with the bag opening facing down and the column vertical. Provide free space for the air bag to expand in case of an accidental deployment. Otherwise, personal injury may result.


    Object Number: 323513  Size: LH
  1. Turn the ignition switch to the OFF position.
  2. Disable the SIR system. Refer to Disabling the SIR System .
  3. Remove the steering wheel inflator module (3). Refer to Inflatable Restraint Steering Wheel Module Replacement .
  4. Remove the steering wheel retaining nut (2).
  5. Remove the steering wheel (1) from the steering column shaft. Refer to Steering Wheel Replacement .

  6. Object Number: 324821  Size: SH
  7. Remove the upper and lower shrouds. Refer to Steering Column Trim Covers - Disassemble - Off Vehicle .
  8. Pop the wire harness assembly (4) out of the wire harness strap (5).
  9. Remove three wire harness straps (3) from the wire harness assembly (4).
  10. Remove one wire harness strap (2) from the upper tilt head assembly (1).

  11. Object Number: 324825  Size: SH
  12. Remove the black SIR connector (2) from the fused jumper assembly connector (1).

  13. Object Number: 324829  Size: SH
  14. Remove the retaining ring (1).
  15. Remove the SIR coil assembly (3).
  16. Remove the wave washer (2).

Installation Procedure


    Object Number: 324831  Size: SH
  1. Install the wave washer (1).

  2. Object Number: 324839  Size: SH
  3. To install the SIR coil assembly:
  4. Align the block tooth on the race and upper shaft assembly (1) to the 12 o' clock position.


    Object Number: 293255  Size: SH
  5. The new SIR coil assembly will be precentered. Refer to Inflatable Restraint Coil Centering - Off Vehicle in Steering.
  6. Pull the tab and remove. Do not depress the tab (1) on the back of the SIR coil assembly.

  7. Object Number: 324859  Size: SH
  8. Align the SIR coil assembly (2) with the horn tower sticking through the shaft lock shield assembly (1).

  9. Object Number: 325104  Size: SH

    Important: The retaining ring (1) must seat securely on the groove of the race and upper shaft assembly (2).

  10. Install the retaining ring (1).

  11. Object Number: 324825  Size: SH
  12. Install the black SIR connector (2) to the fused jumper assembly connector (1).

  13. Object Number: 324821  Size: SH
  14. Pop the wire harness assembly (4) into the wire harness strap (5).
  15. Install one wire harness strap (2) into the steering column tilt head assembly (1).

    Install three wire harness straps (3) onto the wire harness assembly (4).


    Object Number: 323513  Size: LH
  16. Install the upper and lower shrouds. Refer to Steering Column Trim Covers - Assemble - Off Vehicle .
  17. Install the steering wheel (1). Refer to Steering Wheel Replacement .
  18. Install the steering wheel inflator module (3). Refer to Inflatable Restraint Steering Wheel Module Replacement .
  19. Enable the SIR system. Refer to Enabling the SIR System .