Was the Wiper/Washer System Check performed?

--

Go to Step 2

Go to Wiper/Washer System Check

1. Turn the ignition switch OFF.
2. Disconnect wiper switch connector C202.
3. Set the wiper switch to DELAY.
4. Measure the resistance through connector C202 from terminal E5 to terminal E9, using a J 39200.
5. Move the wiper switch through the entire delay range.

Does the resistance vary within the specified range?

91 kohms to 1.2 Mohms

Go to Step 4

Go to Step 3

Replace the wiper/washer switch. Refer to Multifunction Turn Signal Lever Replacement - On Vehicle .

Is the replacement complete?

--

Go to Wiper/Washer System Check

--

Measure the resistance through connector C202 from terminal E5 to terminal E6, using a J 39200.

Is the resistance less than the specified value?

3 ohms

Go to Step 6

Go to Step 5

Replace the wiper/washer switch. Refer to Multifunction Turn Signal Lever Replacement - On Vehicle .

Is the replacement complete?

--

Go to Wiper/Washer System Check

--

1. Reconnect wiper/washer switch connector C202.
2. Disconnect wiper motor connector C1.
3. Turn the ignition switch ON.
4. Set the wiper switch to HI.
5. Measure the voltage from wiper motor connector C1, terminal B, to ground using a J 39200.

Is the measurement within the specified values?

10.5-15 V

Go to Step 8

Go to Step 7

Repair the poor connection or the open in CKT 91.

Is the repair complete?

--

Go to Wiper/Washer System Check

--

Measure the voltage from wiper moptor connector C1, terminal F, to ground using a J 39200.

Is the measurement within the specified values?

10.5-15 V

Go to Step 10

Go to Step 9

Repair the poor connection or the open in CKT 94.

Is the repair complete?

--

Go to Wiper/Washer System Check

--

Replace the wiper motor cover. Refer to Wiper Motor Cover Replacement .

Is the replacement complete?

--

Go to Wiper/Washer System Check

--

Was the Wiper/Washer System Check performed?

--

Go to Step 2

Go to Wiper/Washer System Check

1. Disconnect the Rainsense module connector.
2. Turn the ignition switch ON.
3. Connect a test light between Rainsense module connector terminal 7 and terminal 8.

Is the test light on?

--

Go to Step 6

Go to Step 3

Connect a test light from Rainsense module connector, terminal 8, to ground.

Is the test light on?

--

Go to Step 4

Go to Step 5

Repair the open in CKT 1051.

Is the repair complete?

--

Go to Wiper/Washer System Check

--

Repair the open in CKT 43.

Is the repair complete?

--

Go to Wiper/Washer System Check

--

Is there continuity?

--

Go to Step 8

Go to Step 7

Repair the open in CKT 94.

Is the repair complete?

--

Go to Wiper/Washer System Check

--

Does the resistance vary within the specified range?

91 kohms to 1.2 Mohms

Go to Step 9

Go to Step 10

Is the measurement less than the specified value?

3 ohms

Go to Step 11

Go to Step 10

Replace the wiper/washer switch. Refer to Multifunction Turn Signal Lever Replacement - On Vehicle .

Is the replacement complete?

--

Go to Wiper/Washer System Check

--

1. Reconnect connector C202.
2. Disconnect connector C1.
3. Measure the resistance from connector C1, terminal G, to Rainsense module connector, terminal 9, using a J 39200.

Is the measurement less than the specified value?

3 ohms

Go to Step 13

Go to Step 12

Repair the open in CKT 1715.

Is the repair complete?

--

Go to Wiper/Washer System Check

--

Measure the resistance from connector C1, terminal F, to Rainsense module connector, terminal 5, using a J 39200.

Is the measurement less than the specified value?

3 ohms

Go to Step 15

Go to Step 14

Repair the open in CKT 1714.

Is the repair complete?

--

Go to Wiper/Washer System Check

--

Replace the wiper motor cover. Refer to Wiper Motor Cover Replacement .

Is the problem corrected?

--

Go to Wiper/Washer System Check

Go to Step 16

Replace the rainsense module. Refer to Outside Moisture Sensor Replacement .

Is the replacement complete?

--

Go to Wiper/Washer System Check

--