Driver or Passenger Seat Cushion Heater Replacement DeVille
Repair Procedure
Important: Before installing the new heat element to the seat trim cover, verify that the
seat assembly heat function operates properly with the new heat element connected.
- Remove the front seat cushion trim cover (1). Refer to
Seat Cushion Trim Cover and Pad Replacement
.
- Place the seat trim cover on a clean flat surface with the inside facing
out.
- Use a marker to draw in the cut-lines (2)
on the seat cover (1).
Important: DO NOT attempt to remove the factory heat elements from the seat trim cover.
The new heat element is to be installed between the factory heat element and the seat
trim cover.
- Remove the wiring harness from the non-functioning factory heat element.
4.1. | At the location (3), pull back the tape covering the harness wires. |
4.2. | Use a pair of diagonal side cutters to cut the harness wires as close
to the factory heat element material as possible. |
Important: DO NOT start the cut with a jab or poke.
- At the trim cover edge (2) using a razor blade or an equivalent sharp
tool, slice through the factory heat element material along the cut-line until a hole
is created.
- Insert your fingers through the hole and lift the factory heat element
material (1) away from the trim cover material.
Important: DO NOT cut through seams.
- Using scissors and/or a razor blade, continue to cut the material along the
cut-lines.
Installation Procedure
- Fold back the centers (1) of the factory
heat element material. Insert the service heat element (2), with the backing
paper side up, between the trim cover material and the factory heat element material.
- Carefully remove the backing paper from the new heat element. Ensure the
new heat element is laying flat.
- Unfold the centers (1) of the factory heat element material.
- Match the edges of the factory heat element material
and cover the cut-lines with 3M Highland Cloth Duct Tape, P/N 6969, or equivalent.
Ensure the new and factory heat elements are laying flat.
- Install the front seat cushion trim cover. Refer to
Seat Cushion Trim Cover and Pad Replacement
.
Driver or Passenger Seat Cushion Heater Replacement DHS/DTS
Repair Procedure
Important: Before installing the new heat element to the seat trim cover, verify that the
seat assembly heat function operates properly with the new heat element connected.
- Remove the front seat cushion trim cover (1). Refer to
Seat Cushion Trim Cover and Pad Replacement
.
- Place the seat trim cover on a clean flat surface with the inside facing
out.
- Use a marker to draw in the cut-lines (2)
on the non-functioning factory heat element. Refer to the appropriate illustration.
Important: DO NOT attempt to remove the factory heat elements from the seat trim cover.
The new heat element is to be installed between the factory heat element and the seat
trim cover.
- Remove the wiring harness from the non-functioning factory heat element.
4.1. | At the location (3), pull back the tape covering the harness wires. |
4.2. | Use a pair of diagonal side cutters to cut the harness wires as close
to the factory heat element material as possible. |
Important: DO NOT start the cut with a jab or poke.
- At the trim cover edge (2) using a razor blade or an equivalent sharp
tool, slice through the factory heat element material along the cut-line until a hole
is created.
- Insert your fingers through the hole and lift the factory heat element
material (1) away from the trim cover material.
Important: DO NOT cut through seams.
- Using scissors and/or a razor blade, continue to cut the material along the
cut-lines.
Installation Procedure
- Fold back the centers (1) of the factory
heat element material. Insert the service heat element (2), with the backing
paper side up, between the trim cover material and the factory heat element material.
- Carefully remove the backing paper from the new heat element. Ensure the
new heat element is laying flat.
- Unfold the centers (1) of the factory heat element material.
- Match the edges of the factory heat element material
and cover the cut-lines with 3M Highland Cloth Duct Tape, P/N 6969, or equivalent.
Ensure the new and factory heat elements are laying flat.
- Connect the two thigh heat element electrical connectors to the center
heat element.
- Install the front seat cushion trim cover. Refer to
Seat Cushion Trim Cover and Pad Replacement
.