| Table 1: | IPC Indicators |
| Table 2: | DIC Indicators |
The indicator description and operation uses generic indicator names. Refer to the table below for the indicators that are available on this vehicle:
Vehicle Indicator Name | Indicator Description Title |
|---|---|
Air Bag symbol (Canada) | Air Bag Indicators |
AIR BAG (U.S.) | Air Bag Indicators |
ANTI-LOCK ABS symbol | ABS Indicator |
Battery symbol | Charging System Indicators |
BRAKE symbol | Brake System Indicators |
Check Engine symbol (Canada) | Malfunction Indicator Lamp (MIL) |
Engine Coolant Temperature Warning symbol | Engine Coolant Indicators |
Fasten Safety Belt symbol | Fasten Safety Belt Indicator |
High Beam symbol | Lighting System Indicators |
km/h | km/h and MPH Indicators |
Oil Pressure symbol | Engine Oil Indicators |
MPH | km/h and MPH Indicators |
SECURITY | Theft System Indicators |
SERVICE ENGINE SOON (U.S.) | Malfunction Indicator Lamp (MIL) |
TC symbol (Canada) | Traction Control System Indicators |
TRACTION CONTROL (U.S.) | Traction Control System Indicators |
Turn Signal symbols | Lighting System Indicators |
Vehicle Indicator Name | Indicator Description Title |
|---|---|
APPLY BRAKE TO SHIFT - 46 | Transmission Indicators |
BATTERY NOT CHARGING - 7 | Charging System Indicators |
BATTERY VOLTAGE HIGH - 8 | Charging System Indicators |
BATTERY VOLTAGE LOW - 6 | Charging System Indicators |
CHANGE ENGINE OIL - 82 | Engine Oil Indicators |
CHANGE TRANS FLUID - 47 | Transmission Indicators |
CHECK BRAKE FLUID - 37 | Brake System Indicators |
CHECK COOLANT LEVEL - 2 | Engine Coolant Indicators |
CHECK FUEL GAGE - 39 | Fuel System Indicators |
CHECK GAS CAP - 61 | Fuel System Indicators |
CHECK OIL LEVEL - 36 | Engine Oil Indicators |
CHECK WASHER FLUID - 25 | Washer Fluid Indicator |
CRUISE ENGAGED - 43 | Cruise Control Indicator |
DOOR AJAR - 141 | Door Ajar Indicators |
DRIVER DOOR AJAR - 140 | Door Ajar Indicators |
ENGINE COOLANT HOT, IDLE ENGINE - 44 | Engine Coolant Indicators |
ENGINE HOT - AC OFF - 16 | Engine Coolant Indicators |
ENGINE MISFIRE - EASE OFF GAS PEDAL - 114 | Engine Misfire Indicator |
ENGINE OVERHEATED, STOP ENGINE - 42 | Engine Coolant Indicators |
ENGINE POWER REDUCED - 41 | Reduced Engine Power Indicator |
FUEL LEVEL LOW - 11 | Fuel System Indicators |
HEADLAMPS SUGGESTED - 23 | Lighting System Indicators |
ICE POSSIBLE - 13 | Ice Indicator |
LOW REFRIG AC OFF - 12 | HVAC System Indicators |
MONITORED SYSTEMS OK - 1 | Status Indicators |
OIL PRESSURE LOW STOP ENGINE - 35 | Engine Oil Indicators |
OPTIONS NOT SET - 99 | Status Indicators |
PROGRAM PASS KEY - 31 | Theft System Indicators |
REMOVE KEY - 70 | Theft System Indicators |
SERVICE AC SYSTEM - 14 | HVAC System Indicators |
SERVICE AIR BAG - 83 | Air Bag Indicators |
SERVICE CHARGING SYS - 102 | Charging System Indicators |
SERVICE ELECTRICAL SYS - 106 | Electrical System Indicators |
SERVICE FUEL SYSTEM - 101 | Fuel System Indicators |
SERVICE IDLE CONTROL - 107 | Idle Control Indicator |
SERVICE RIDE SYS - 84 | Suspension System Indicators |
SERVICE STEERING SYS - 127 | Steering System Indicator |
SERVICE TRANSMISSION - 100 | Transmission Indicators |
SERVICE VEHICLE SOON - 3 | Electrical System Indicators |
SERV STABILITY SYS - 54 | Stability System Indicators |
STABILITY ENGAGED - 55 | Stability System Indicators |
STARTING DISABLED REMOVE KEY - 33 | Theft System Indicators |
THEFT SYSTEM PROBLEM CAR MAY NOT RESTART - 34 | Theft System Indicators |
TOP SPEED FUEL CUT-OFF - 111 | Engine Overspeed Indicator |
TRACTION ENGAGED - 91 | Traction Control System Indicators |
TRACTION OFF - 89 | Traction Control System Indicators |
TRACTION READY - 90 | Traction Control System Indicators |
TRACTION SUSPENDED - 56 | Traction Control System Indicators |
TRANS FLUID RESET - 48 | Transmission Indicators |
TRANS HOT IDLE ENGINE - 112 | Transmission Indicators |
TRUNK OPEN - 24 | Trunk Ajar Indicator |
TURN SIGNAL ON - 20 | Lighting System Indicators |
VEHICLE OVERSPEED - 52 | Vehicle Overspeed Indicator |
VEHICLE SPEED LIMITED TO XXX MPH - 113 | Suspension Indicators |
ABS Indicator
The IPC illuminates the ANTI-LOCK (ABS) indicator when the following occurs:
| • | The electronic brake control module (EBCM) detects a malfunction with the antilock brake system. The IPC receives a class 2 message from the EBCM requesting illumination. |
| • | The IPC detects a loss of class 2 communications with the EBCM and the discrete back-up ABS indicator signal is open. |
| • | The IPC performs the displays test at the start of each ignition cycle. The indicator illuminates for approximately 3 seconds. |
When the ABS indicator is commanded on, the IPC also illuminates the TRACTION CONTROL indicator and illuminates the SERV STABILITY SYS indicator in the DIC.
Air Bag Indicators
AIR BAG
The IPC illuminates the AIR BAG indicator when the following occurs:
| • | The inflatable restraint sensing and diagnostic module (SDM) detects a malfunction with the supplemental inflatable restraint system. The IPC receives a class 2 message from the SDM requesting illumination. |
| • | The IPC detects a loss of class 2 communications with the SDM. |
| • | The IPC performs the displays test at the start of each ignition cycle. The IPC flashes the air bag indicator 7 times. |
SERVICE AIR BAG -- 83
The IPC illuminates the SERVICE AIR BAG -- 83 indicator in the DIC when the following occurs:
| • | The inflatable restraint sensing and diagnostic module (SDM) detects a malfunction with the supplemental inflatable restraint system. The IPC receives a class 2 message from the SDM requesting illumination. |
| • | The IPC detects a loss of class 2 communications with the SDM. |
Brake System Indicators
BRAKE
The IPC illuminates the BRAKE indicator and activates an audible warning when the following occurs:
| • | The IPC detects that the park is applied (signal circuit is low). |
| • | The IPC detects a low brake fluid condition (signal circuit is low). |
| • | The IPC performs the displays test at the start of each ignition cycle. The indicator illuminates for approximately 3 seconds. |
CHECK BRAKE FLUID - 37
The IPC illuminates the CHECK BRAKE FLUID - 37 indicator in the DIC and sends a class 2 message in order to activate an audible warning when the IPC detects that the brake fluid level is below the normal operating range.
Charging System Indicators
Charge
The IPC illuminates the charge indicator when the following occurs:
| • | The PCM detects that the generator output is less than 11 volts or greater than 16 volts. The IPC receives a class 2 message from the PCM requesting illumination. |
| • | The IPC determines that the system voltage is less than 11 volts or greater than 16 volts. |
| • | The IPC performs the displays test at the start of each ignition cycle. The indicator illuminates for approximately 3 seconds. |
BATTERY NOT CHARGING - 7
The IPC illuminates the BATTERY NOT CHARGING - 7 indicator in the DIC when the PCM detects a malfunction with the generator output. The IPC receives a class 2 message from the PCM requesting illumination.
BATTERY VOLTAGE HIGH - 8
The IPC illuminates the BATTERY VOLTAGE HIGH - 8 indicator in the DIC when the IPC determines that the system voltage is greater than 16 volts.
BATTERY VOLTAGE LOW - 6
The IPC illuminates the BATTERY VOLTAGE LOW - 6 indicator in the DIC when the IPC determines that the system voltage is less than 11 volts.
SERVICE CHARGING SYSTEM - 102
The IPC illuminates the SERVICE CHARGING SYSTEM - 102 indicator in the DIC when the PCM detects a malfunction with the generator output. The IPC receives a class 2 message from the PCM requesting illumination.
Cruise Control Indicator
CRUISE ENGAGED 43
The IPC illuminates the CRUISE ENGAGED 43 - Indicator in the DIC when the powertrain control module (PCM) detects that the cruise control is requested. The IPC receives a class 2 message from the PCM requesting illumination.
Door Ajar Indicators
DOOR AJAR - 141
The IPC illuminates the DOOR AJAR - 141 Indicator in the DIC when the IPC detects the passenger door is open and the transmission is out of park. If the vehicle speed is greater than 4.8 km/h (3 mph), the IPC sends a class 2 message to activate an audible warning.
DRIVER DOOR AJAR -140
The IPC illuminates the DRIVER DOOR AJAR -140 indicator in the DIC when the IPC detects the driver's door is open and the transmission is out of park. If the vehicle speed is greater than 8 km/h (5 mph), the IPC sends a class 2 message in order to activate an audible warning.
Electrical System Indicators
SERVICE ELECTRICAL SYS - 106
The IPC illuminates the SERVICE ELECTRICAL SYS - 106 indicator in the DIC when the powertrain control module (PCM) or the IPC detects certain malfunctions in the vehicle electrical system. The IPC receives a class 2 message from the PCM requesting illumination.
SERVICE VEHICLE SOON - 3
The IPC illuminates the SERVICE VEHICLE SOON - 3 indicator in the DIC when the powertrain control module (PCM) detects certain malfunctions that are unrelated to the emission system. The IPC receives a class 2 message from the PCM requesting illumination.
Engine Coolant Indicators
Engine Coolant
The IPC illuminates the engine coolant indicator and activates an audible warning when the following occurs:
| • | The IPC determines that the coolant temperature is greater than 128°C (262°F). The IPC receives a class 2 message from the PCM indicating the coolant temperature. |
| • | The IPC performs the displays test at the start of each ignition cycle. The indicator illuminates for approximately 3 seconds. |
The IPC turns OFF the engine coolant indicator when the engine coolant falls below 125°C (257°F).
CHECK COOLANT LEVEL - 2
The IPC illuminates the CHECK COOLANT LEVEL - 2 indicator in the DIC when the IPC detects that the coolant level is low/signal circuit is high.
ENGINE COOLANT HOT/IDLE ENGINE - 44
The IPC illuminates the ENGINE COOLANT HOT/IDLE ENGINE - 44 indicator in the DIC and activates an audible warning when the IPC determines that the coolant temperature is greater than 128°C (262°F). The IPC receives a class 2 message from the PCM indicating the coolant temperature.
The IPC turns OFF the indicator when the engine coolant falls below 125°C (257°F).
ENGINE HOT - AC OFF - 16
The IPC illuminates the ENGINE HOT - AC OFF - 16 indicator in the DIC when the heater and A/C programmer detects that the engine temperature is above the normal operating range and has turned off the air conditioning in order to allow the engine to cool down. The IPC receives a class 2 message from the heater and A/C programmer requesting illumination.
ENGINE OVERHEATED/STOP ENGINE - 42
The IPC illuminates the ENGINE OVERHEATED/STOP ENGINE - 42 indicator in the DIC and activates an audible warning when the power train control module (PCM) detects that the engine temperature is above the normal operating range. The IPC receives a class 2 message from the PCM requesting illumination.
Engine Misfire Indicator
ENGINE MISFIRE - - EASE OFF GAS PEDAL - 114
The IPC illuminates the ENGINE MISFIRE - - EASE OFF GAS PEDAL - 114 indicator in the DIC when the powertrain control module (PCM) detects an engine misfire. The IPC receives a class 2 message from the PCM requesting illumination.
Engine Oil Indicators
CHANGE ENGINE OIL - 82
The IPC illuminates the CHANGE ENGINE OIL - 82 indicator in the DIC when the powertrain control module (PCM) has determined that the engine oil life index is zero. The IPC receives a class 2 message from the PCM requesting illumination.
CHECK OIL LEVEL - 36
The IPC illuminates the CHECK OIL LEVEL - 36 indicator in the DIC when the powertrain control module (PCM) detects that the engine oil level is low. The IPC receives a class 2 message from the PCM requesting illumination.
Engine Oil Pressure
The IPC illuminates the engine oil pressure indicator and activates an audible warning when the following occurs:
| • | The powertrain control module (PCM) detects that the engine oil pressure is outside the normal operating range. The IPC receives a class 2 message from the PCM requesting illumination. |
| • | The IPC performs the displays test at the start of each ignition cycle. The indicator illuminates for approximately 3 seconds. |
OIL PRESSURE LOW/STOP ENGINE - 35
The IPC illuminates the OIL PRESSURE LOW/STOP ENGINE - 35 indicator in the DIC and activates an audible warning when the powertrain control module (PCM) detects that the engine oil pressure is outside the normal operating range. The IPC receives a class 2 message from the PCM requesting illumination.
Engine Overspeed Indicator
TOP SPEED FUEL CUT-OFF - 111
The IPC illuminates the TOP SPEED FUEL CUT-OFF - 111 indicator in the DIC when the powertrain control module (PCM) enables the fuel-cut off function in order to restrict vehicle speed. The IPC receives a class 2 message from the PCM requesting illumination.
Fasten Safety Belt Indicator
The IPC illuminates the fasten safety belt indicator when the following occurs:
| • | The inflatable restraint sensing and diagnostic module (SDM) detects that the driver's seat belt is unbuckled when the ignition is turned ON. The IPC receives a class 2 message from the SDM requesting illumination. The IPC illuminates the indicator for 72 seconds or until the driver's safety belt is buckled. The IPC also sends a class 2 message in order to activate an audible warning. |
| • | The inflatable restraint sensing and diagnostic module (SDM) detects that the driver's safety belt is unbuckled after the ignition has been turned ON. The IPC receives a class 2 message from the SDM requesting illumination. The IPC illuminates the indicator for 72 seconds or until the driver's safety belt is buckled. |
| • | The IPC performs the displays test at the start of each ignition cycle. The indicator illuminates for approximately 4 seconds. |
Fuel System Indicators
CHECK FUEL GAGE - 39
The IPC illuminates the CHECK FUEL GAGE - 39 indicator in the DIC and activates an audible warning when the IPC is in the gauges OFF mode and the fuel level is less than 13.2 liters (3.5 gallons). The IPC receives a class 2 message from the body control module (BCM) indicating the fuel level.
CHECK GAS CAP - 61
The IPC illuminates the CHECK GAS CAP - 61 indicator in the DIC when the powertrain control module (PCM) detects a malfunction in the evaporative emissions system or the gas cap is not seated properly. The IPC receives a class 2 message from the PCM requesting illumination.
FUEL LEVEL LOW - 11
The IPC illuminates the FUEL LEVEL LOW - 11 indicator in the DIC and activates an audible warning when the fuel level is less than 11.4 liters (3 gallons). The IPC receives a class 2 message from the body control module (BCM) indicating the fuel level.
SERVICE FUEL SYSTEM - 101
The IPC illuminates the SERVICE FUEL SYSTEM - 101 indicator in the DIC when the powertrain control module (PCM) detects certain malfunctions in the fuel system. The IPC receives a class 2 message from the PCM requesting illumination.
HVAC System Indicators
LOW REFRIG AC OFF - 12
The IPC illuminates the LOW REFRIG AC OFF - 12 Indicator in the DIC when the heater and A/C programmer detects the A/C system refrigerant is out side of the normal operating range. The IPC receives a class 2 message from the heater and A/C programmer requesting illumination.
SERVICE AC SYSTEM - 14
The IPC illuminates the SERVICE AC SYSTEM - 14 indicator in the DIC when the heater and A/C programmer has detected a malfunction in the air conditioning system. The IPC receives a class 2 message from the heater and A/C programmer requesting illumination.
Ice Indicator
ICE POSSIBLE - 13
The IPC illuminates the ICE POSSIBLE - 13 indicator in the DIC when the outside air temperature drops below 2.2°C (36°F).
Idle Control Indicator
SERVICE IDLE CONTROL - 107
The IPC illuminates the SERVICE IDLE CONTROL - 107 indicator in the DIC when the powertrain control module (PCM) detects certain malfunctions in the idle control system. The IPC receives a class 2 message from the PCM requesting illumination.
km/h and MPH Indicators
km/h
The IPC illuminates the km/h indicator when IPC detects that the speedometer has been requested to display metric units. The IPC receives a discrete input from the LH instrument cluster switch requesting metric units be displayed.
MPH
The IPC illuminates the MPH indicator when IPC detects that the speedometer has been requested to display English units. The IPC receives a discrete input from the LH instrument cluster switch requesting English units be displayed.
Lighting System Indicators
HEADLAMPS SUGGESTED -- 23
The IPC illuminates the HEADLAMPS SUGGESTED -- 23 indicator in the DIC when the IPC detects that the ambient light conditions are low enough that headlamps should be used during driving.
High Beam
The IPC illuminates the high beam indicator when the IPC detects that the high beams are requested.
Turn Signals
The IPC illuminates the right or left turn signal indicator when the IPC detects a turn signal or a hazard request. If the IPC determines that the turn signal is active for more than 1.6 km (1 mile), the IPC sends a class 2 message in order to activate an audible warning.
TURN SIGNAL ON -- 20
The IPC illuminates the TURN SIGNAL ON -- 20 indicator in the DIC and sends a class 2 message in order to activate an audible warning when the IPC determines that the turn signal is active for more than 1.6 km (1 mile).
Malfunction Indicator Lamp (MIL)
The PCM illuminates the MIL (service engine soon or check engine) when the following occurs:
| • | The PCM detects a malfunction in the emissions system. |
| • | The PCM performs the displays test at the start of each ignition cycle. The indicator illuminates for approximately 3 seconds. |
| • | The ignition is on, with the engine off. |
Reduced Engine Power Indicator
ENGINE POWER REDUCED - 41
The IPC illuminates the ENGINE POWER REDUCED - 41 indicator in the DIC when the powertrain control module (PCM) detects a malfunction in the throttle actuator control (TAC) system. The IPC receives a class 2 message from the PCM requesting illumination.
Stability System Indicators
SERV STABILITY SYS -- 54
The IPC illuminates the SERV STABILITY SYS -- 54 indicator in the DIC when the electronic brake control module (EBCM) detects a malfunction with the stability system. The IPC receives a class 2 message from the EBCM requesting illumination.
STABILITY ENGAGED -- 55
The IPC illuminates the STABILITY ENGAGED -- 55 indicator in the DIC when electronic brake control module (EBCM) detects a stability system event. The IPC receives a class 2 message from the EBCM requesting illumination.
Status Indicators
MONITORED SYSTEMS OK - 1
The IPC illuminates the MONITORED SYSTEMS OK - 1 Indicator in the DIC when the DIC is in the recall mode and no driver warning messages are active.
OPTIONS NOT SET - 99
The IPC illuminates the OPTIONS NOT SET - 99 Indicator when the IPC detects that no options are set or a malfunction has been detected in the IPCs memory.
Steering System Indicator
SERVICE STEERING SYS - 127
The IPC illuminates the SERVICE STEERING SYS - 127 indicator in the DIC when the electronic brake control module (EBCM) has detected a malfunction in the variable effort steering (VES) system. The IPC receives a class 2 message from the EBCM requesting illumination.
Suspension System Indicators
SERVICE RIDE SYS - 84
The IPC illuminates the indicator in the DIC when the electronic suspension control module has detected a malfunction in the road sensing suspension system. The IPC receives a class 2 message from the electronic suspension control module requesting illumination.
VEHICLE SPEED LIMITED TO XXX - 113
The IPC illuminates the VEHICLE SPEED LIMITED TO XXX - 113 indicator in the DIC when the powertrain control module (PCM) has detected a malfunction in the road sensing suspension system that requires the vehicle speed to be limited. The IPC receives a class 2 message from the PCM requesting illumination.
Theft System Indicators
PROGRAM PASS KEY - 31
The IPC illuminates the PROGRAM PASS KEY - 31 indicator in the DIC when the IPC detects the ignition key pellet information has not been programed.
SECURITY
The vehicle theft deterrent (VTD) system utilizes the IPC to control the VTD functions. The IPC illuminates the SECURITY indicator when it detects a malfunction with the VTD system. The content theft deterrent (CTD) system utilizes the body control module (PZM) to control the VTD functions. The IPC receives a class 2 message from the PZM requesting illumination.
| • | The VTD system requests the IPC to illuminate the indicator only when the ignition switch is ON. The VTD system uses the indicator as a malfunction indicator. |
| • | The CTD system requests the IPC to illuminate the indicator only when the ignition switch is OFF. The CTD system uses the indicator in order to identify system status. |
| • | The IPC performs the displays test at the start of each ignition cycle. The indicator illuminates for approximately 3 seconds. |
STARTING DISABLED REMOVE KEY - 33
The IPC illuminates the STARTING DISABLED/REMOVE KEY -- 33 indicator in the DIC when the powertrain control module (PCM) has not received a fuel enable signal from the IPC prior to an attempted vehicle start. The IPC receives a class 2 message from the PCM requesting illumination. After the ignition is cycled to OFF the IPC illuminates WAIT 3 MINUTES, WAIT 2 MINUETS, WAIT 1 MINUTE and than START CAR, REMOVE KEY in the DIC.
THEFT SYSTEM PROBLEM CAR MAY NOT RESTART - 34
The IPC illuminates the THEFT SYSTEM PROBLEM CAR MAY NOT RESTART - 34 indicator in the DIC when the IPC detects a theft system malfunction well the engine is running. The vehicle will continue to run but may not restart if the malfunction is still present when engine is turned OFF.
Traction Control System Indicators
TRACTION CONTROL
The IPC illuminates the TRACTION CONTROL indicator when the following occurs:
| • | The electronic brake control module (EBCM) detects a malfunction in the traction control system. The IPC receives a class 2 message from the EBCM requesting illumination. |
| • | The IPC detects a loss of class 2 communications with the EBCM. |
| • | The IPC performs the displays test at the start of each ignition cycle. The indicator illuminates for approximately 3 seconds. |
TRACTION ENGAGED - 91
The IPC illuminates the TRACTION ENGAGED -- 91 indicator in the DIC when the electronic brake control module (EBCM) detects a traction control event. The IPC receives a class 2 message from the EBCM requesting illumination.
TRACTION OFF - 89
The IPC illuminates the TRACTION OFF -- 89 indicator in the DIC when the driver disables the traction control system. The IPC receives a class 2 message from the EBCM requesting illumination.
TRACTION READY - 90
The IPC illuminates the TRACTION READY - 90 indicator in the DIC when the driver enables the traction control system. The IPC receives a class 2 message from the EBCM requesting illumination.
TRACTION SUSPENDED - 56
The IPC illuminates the TRACTION SUSPENDED - 56 indicator in the DIC when the electronic brake control module (EBCM) disables the traction control system. The IPC receives a class 2 message from the EBCM requesting illumination.
Transmission Indicators
APPLY BRAKE TO SHIFT - 46
The IPC illuminates the APPLY BRAKE TO SHIFT - 46 Indicator in the DIC when the powertrain control module (PCM) determines the transmission is in park and the brake is not applied. The IPC receives a class 2 message from the PCM requesting illumination.
CHANGE TRANS FLUID - 47
The IPC illuminates the CHANGE TRANS FLUID - 47 indicator in the DIC when the powertrain control module (PCM) has determined that the transmission oil life index is zero. The IPC receives a class 2 message from the PCM requesting illumination.
SERVICE TRANSMISSION - 100
The IPC illuminates the SERVICE TRANSMISSION - 100 indicator in the DIC when the powertrain control module (PCM) detects certain malfunctions in the transmission. The IPC receives a class 2 message from the PCM requesting illumination.
TRANS FLUID RESET - 48
The IPC illuminates the TRANS FLUID RESET - 48 indicator in the DIC when the powertrain control module (PCM) has determined that the transmission oil life has been reset to 100 percent. The IPC receives a class 2 message from the PCM requesting illumination.
TRANS HOT IDLE ENGINE - 112
The IPC illuminates the TRANS HOT IDLE ENGINE - 11 indicator in the DIC and sends a class 2 message in order to activate an audible warning when the powertrain control module (PCM) detects that the transmission temperature is above the normal operating range. The IPC receives a class 2 message from the PCM requesting illumination.
Trunk Ajar Indicator
TRUNK OPEN - 24
The IPC illuminates the TRUNK OPEN - 24 indicator in the DIC when the body control module (PZM) detects that the rear compartment is open and the ignition is ON. The IPC receives a class 2 message from the PZM requesting illumination.
Vehicle Overspeed Indicator
VEHICLE OVERSPEED - 52 (Export)
The IPC illuminates the VEHICLE OVERSPEED - 52 indicator in the DIC and sends a class 2 message in order to activate an audible warning when the powertrain control module (PCM) detects that the vehicle speed is greater than 120 km/h (74.5 MPH). The IPC receives a class 2 message from the PCM requesting illumination.
Washer Fluid Indicator
CHECK WASHER FLUID - 25
The IPC illuminates the CHECK WASHER FLUID - 25 indicator in the DIC when the IPC detects a low washer fluid condition (signal circuit is low).
