Steering Shaft, Lower Bearing, and Jacket - Disassemble - Off Vehicle Power Tilt and Telescope
Tools Required
J 21854-01 Pivot
Pin Remover
- Remove the windshield wiper and washer switch assembly only. Refer
to
Windshield Wiper and Washer Switch Assembly - Disassemble - Off Vehicle
.
- Remove the cruise control switch assembly only. Refer to
Cruise Control Switch Assembly - Disassemble - Off Vehicle
.
- Remove the signal switch
housing assembly.
- Remove the 2 pan head tapping screws from the turn signal
and multifunction switch assembly.
- Remove the turn signal and multifunction switch assembly.
- Remove the steering shaft
seal (1).
- Remove the sensor retainer (2).
- Remove the hi resolution steering wheel position sensor assembly (3).
- Remove the lower spring
retainer (1).
- Remove the wave washer (2).
- Remove the adapter and bearing assembly (3).
- Remove the 2 pivot
pins (1) using J 21854-01
.
- Remove the ball stud (2)
from the steering column tilt head assembly (1).
- Remove the steering column
tilt head assembly (1) with the steering shaft assembly from the steering
jacket assembly.
- Remove the steering shaft
assembly (1) from the steering column tilt head assembly.
Important: Mark the upper shaft assembly and the steering shaft assembly to ensure
proper assembly. Failure to assemble properly will cause the steering wheel
to be turned 180 degrees.
- Tilt the upper shaft assembly 90 degrees to the steering shaft
assembly and disengage. If necessary, remove and discard the old centering
sphere and spring.
- Remove the 4 TORX®
head screws (3) from the tilt actuator assembly (2) that is
mounted on the steering column support assembly (1).
- Remove the retaining ring (1),
compression spring (2), shoulder bolt, (3) and the anti rotation
ball (4) from the steering column support assembly (5).
- Remove the 4 TORX®
head screws (2) from the telescope actuator assembly (3) that
is mounted on the telebearing and jacket assembly (1).
- Remove the 4 TORX®
head screws (1).
- Remove the steering column support assembly (3) from the
telebearing and jacket assembly (2).
Steering Shaft, Lower Bearing, and Jacket - Disassemble - Off Vehicle Manual Tilt
Tools Required
• | J 42137 Lock
Plate Compressor Adapter |
- Remove the inflatable restraint steering wheel module coil. Refer
to
Inflatable Restraint Steering Wheel Module Coil Disassemble - Off Vehicle
.
- Remove the upper tilt head assembly. Refer to
Steering Column Tilt Head Housing - Disassemble - Off Vehicle
.
- Remove the bearing retainer (1)
using J 23653-SIR
and J 42137
.
- Remove the cam orientation plate (2).
- Remove the turn signal
cancel cam assembly (4).
- Remove the upper bearing spring (3).
- Remove the upper bearing inner race seat (2).
- Remove the inner race (1).
- Remove the blue (1),
and gray (2) connectors of the turn signal and multifunction switch
assembly.
- Remove the 2 pan
head tapping screws.
- Remove the turn signal
and multifunction switch assembly.
- Remove the 2 pan
head tapping screws (2).
- Remove the signal switch housing assembly (1).
- Remove the steering shaft
seal (1).
- Remove the sensor retainer (2).
- Remove the hi resolution steering wheel position sensor assembly (3).
- Remove the lower spring
retainer (1).
- Remove the lower bearing spring (2).
- Remove the lower bearing seat (3).
- Remove the adapter and bearing assembly (4).
- Remove the tilt spring.
Refer to the tilt spring assembly
Tilt Spring - Disassemble - Off Vehicle
.
- Remove the 2 pivot pins (1).
- Remove the steering column
tilt head assembly (1) with the steering shaft assembly. Install the
tilt arm and pull to disengage the steering column tilt head assembly (1)
from the jacket column assembly.
- Remove the steering shaft
assembly (1) from the steering column tilt head assembly.
Important: Mark the race and upper shaft assembly and the lower steering shaft
assembly to ensure proper assembly. Failure to assemble properly will cause
steering wheel to be turned 180 degrees.
- Tilt the race and upper shaft assembly 90 degrees to the lower
steering shaft assembly and disengage. If necessary, remove and discard the
old centering sphere and spring.
- Remove the 4 TORX®
head screws (2).
- Remove the steering column support assembly (1).