GM Service Manual Online
For 1990-2009 cars only

Repair Information for Reconnection of Rear Window Defroster Contact or Tab

Subject:Repair Information for Reconnection of Rear Window Defroster Contact or Tab

Models:2000-2009 GM Passenger Cars and Trucks (including Saturn)
2003-2009 HUMMER H2
2006-2009 HUMMER H3
2005-2009 Saab 9-7X
2007-2009 Opel GT
2007-2008 Daewoo G2X
with Electric Rear Window Defroster (RPO C49)



This bulletin is being revised to update the applicable model years. Please discard Corporate Bulletin Number 03-08-48-006D (Section 08 - Body and Accessories).


Repair Suggestions

Soldering Defroster Contact Tabs

In most applications it is preferable to create a new solder connection to reattach a separated rear defroster tab. If you take note of the steps below, it is possible to create a new solder joint that is equal to, or stronger than, the original. The generic procedure below is not very time intensive, but does include minor preparation work to create a good bonding surface. Be sure to follow each of the steps as combined they will produce the strongest bond possible. Please consider the following before attempting the repair:

    â€¢ Soldering introduces significant heat to the glass window of the vehicle. When performing the re-connection of the tab, use only the heat required to do the job. Pre-Heat the soldering iron, have the solder in your other hand ready to go the moment you have enough heat to melt the solder.
    â€¢ If it is winter; bring the vehicle into the service garage and remove any snow from the back window area. Allow time for the glass to warm to the temperature inside the building. Soldering creates a "hot spot" in the glass. DO NOT solder on cold glass.

       Caution: Heating the glass excessively, or repeatedly without time to cool, may result in glass breakage. ALWAYS wear safety glasses when performing this repair!

    â€¢ You must use a Silver-Bearing Solder to make the connection. DO NOT attempt this repair with conventional Lead / Tin solders. Silver Bearing Solder will adhere to the electrical buss bar making a strong and lasting repair.
    â€¢ Protect surfaces under the area to be soldered. It is very easy to drip solder when performing this repair. Just placing a shop towel under the soldering area is sufficient protection.

Soldering Procedure

  1. In many cases the terminal tab will still be in the connector when you examine the vehicle. For Chevrolet Tahoe, Suburban, GMC Yukon, and Cadillac Escalade vehicles (with moveable glass), always replace the defroster tab (GM P/N 25916031). For all other vehicles, please reconnect the original defroster tab.
  2. Important: DO NOT re-use the existing defroster tab on new style utility (GMT900) vehicles with moveable glass.


    Object Number: 2000236  Size: SH
  3. Prepare the surface of the used defroster tab (Not required for new tabs on new style utility models (GMT 900) and the defroster buss bar with fine grain (500 grit) sandpaper or Emery cloth. It is not necessary to remove all of the original solder but it should be scuffed sufficiently so that no oxidation is present. The photo above shows a close up of a properly prepared surface.
  4. Tip
    You may want to mask the glass around the contact area with tape. This is easy to do and will allow you to safely prepare the contact surface without the risk of scratching the glass or the black painted shading.

    Important: Most rear glass has a black painted masking around the edge of the glass. When cleaning up the connection surface be very careful not to damage the surface of the black shading or the surface of the glass.


    Object Number: 2000238  Size: SH
  5. Wipe the newly prepared contact area with Kent Automotive Acrysol (or equivalent) to remove any residual oil or dirt.

  6. Object Number: 2000229  Size: SH

    Object Number: 2000232  Size: SH

    Important: You must use a Silver-Bearing Solder to make the solder joint. DO NOT attempt this repair with conventional Lead / Tin solders. Most suppliers have this type of solder available, and it is available nationally at Radio Shack. It is sold in several diameters and either are acceptable for this repair.

  7. For this step, it is permitted that two technicians be used if required. Heat the new contact on the surface of the buss bar that is to be soldered. Long nose pliers are suggested to hold the contact in place. Keep the solder ready and begin flowing out the solder as soon as the melting temperature has been reached.
  8. Tip
    If a single technician is attempting this repair, it is sometimes beneficial to wrap one turn of the solder around the new contacts base. In this manner as the melting point of the solder is reached, a layer is deposited on the bottom side of the contact.

    Important: Try to align the new contact so that it is positioned with the same attitude as the original contact.


    Object Number: 2000227  Size: SH
  9. The photo above pictures an ideal finished solder joint. Additional stray solder will not harm the performance of the bond however, while it is unlikely that customers may refer to the appearance of the rear window defroster and its components as a positive styling feature of the vehicle interior, it is easy to elicit the opposite reaction due to a poor cosmetic application.
  10. Remove and replace the rear defogger electrical power connector by crimping a new connector to the feed wire. The proper connector can be found in the Packard Electrical Assortment, Tray 18, Position 5. The connector is P/N 12034110.
  11. Apply a small amount of GM Vehicle Care Dielectric Lubricant to the rear defogger connector.
  12. Connect the electrical connector to the defroster tab. Be sure to fully engage the connector. An improperly seated connector may cause excessive resistance and hamper proper operation of the defroster.

Parts Information

Acrysol can be ordered directly from Kent Automotive at 1-800-654-6333 (in Canada, 1-800-563-1717).

Radio Shack products can be found nationally at retail locations, www.radioshack.com, or at 1-800-843-7422.

In Canada, use The Source by Circuit City -- www.thesourcecc.ca or 1-866-454-4426 (English) or 1-866-544-4431 (French).

The balance of the parts list can be ordered through GMSPO.

Part Number

Description

25916031

Tab, Defroster Power (new style utility models (GMT900))

12034110 (Tray 18, Position 5)

Rear Defroster Electrical Power Connector (Packard Electrical Assortment Only)

64-013E

Radio Shack Silver Solder (0.22 dia)

64-026E

Radio Shack Silver Solder (0.62 dia)

P20005

Kent Automotive Acrysol Solvent (32 fl. oz.) 946 ml

12377900 (U.S.)

10953529 (Canada)

GM Vehicle Care Dielectric Lubricant (2 fl. oz.)

Warranty Information (excluding Saab U.S. Models)

For vehicles repaired under warranty, use:

Labor Operation

Description

Labor Time

N9577*

Defroster, Electrical Connection - Reattach

0.3 hr

*This labor operation number is for bulletin use only. This number will not be published in the Labor Time Guide.

Warranty Information (Saab U.S. Models)

For vehicles repaired under warranty, use:

Labor Operation

Description

Failed Object

Fault/Reason Code

Location Code

Warranty Type

Repair/Action Code

Labor Time

8435305

Defroster, Electrical Connection - Reattach

84353

61

0

01

05

0.3 hr