Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Place the turn/hazard lamp switch in the ON position. Are any of the hazard lamps flashing correctly when the hazard switch is placed in the ON position? | -- | Go to Step 2 | Go to Step 17 |
2 | Visually and physically check each lamp that does not flash when the turn/hazard lamp switch is in the ON position. Are the lamps okay? | -- | Go to Step 4 | Go to Step 3 |
3 | Replace the defective lamps. Is the repair complete? | -- | System OK | -- |
4 | Place the turn/hazard lamp switch in the ON position. Is the right rear hazard lamp flashing? | -- | Go to Step 8 | Go to Step 5 |
5 |
Does the test lamp flash? | -- | Go to Step 6 | Go to Step 7 |
6 | Repair the open in CKT 19 (DK GRN) between the turn/hazard lamp switch and the hazard lamp. Is the repair complete? | -- | System OK | -- |
7 | Replace the turn/hazard lamp switch. Refer toTurn Signal and Multifunction Switch Assembly - Disassemble - Off Vehicle in Steering Wheel and Column - Tilt. Is the repair complete? | -- | System OK | -- |
8 | Place the turn/hazard lamp switch in the ON position. Is the left rear hazard lamp flashing? | -- | Go to Step 11 | Go to Step 9 |
9 |
Does the test lamp flash? | -- | Go to Step 10 | Go to Step 7 |
10 | Repair the open in CKT 18 (YEL) between the turn/hazard lamp switch and the hazard lamp. Is the repair complete? | -- | System OK | -- |
11 | Place the turn/hazard lamp switch in the ON position. Is the left front hazard lamp flashing? | -- | Go to Step 14 | Go to Step 12 |
12 |
Does the test lamp flash? | -- | Go to Step 13 | Go to Step 7 |
13 | Repair the open in CKT 14 (LT BLU) between the turn/hazard lamp switch and the hazard lamp. Is the repair complete? | -- | System OK | -- |
14 | Place the turn/hazard lamp switch in the ON position. Is the right front hazard lamp flashing? | -- | System OK | Go to Step 15 |
15 |
Does the test lamp flash? | -- | Go to Step 16 | Go to Step 7 |
16 | Repair the open in CKT 15 (DK BLU) between the turn/hazard lamp switch and the hazard lamp. Is the repair complete? | -- | System OK | -- |
17 | Inspect the STOP/HAZ fuse in the fuse block. Is the STOP/HAZ fuse open? | -- | Go to Step 18 | Go to Step 19 |
18 | Inspect and repair the source of the overload in CKT 140 ORN. Is the repair complete? | -- | System OK | -- |
19 | Connect a test lamp from the STOP/HAZ fuse, cavity C 7 to ground. Did the test lamp light? | -- | Go to Step 21 | Go to Step 20 |
20 | Repair the open in CKT 142 (RED) between the fuse block and the engine wiring harness junction block. Is the repair complete? | -- | System OK | -- |
21 | Connect a test lamp between the turn/hazard lamp switch, cavity E 8 and ground. Did the test light illuminate? | -- | Go to Step 23 | Go to Step 22 |
22 | Locate and repair the open in CKT 140 (ORN) between the turn/hazard lamp switch, cavity E 8 and the STOP/HAZ fuse. Is the repair complete? | -- | System OK | -- |
23 |
Did the test light illuminate? | -- | Go to Step 24 | Go to Step 7 |
24 |
Did the test light illuminate? | -- | Go to Step 26 | Go to Step 25 |
25 | Repair the open in CKT 1696 (GRY) between the turn/hazard lamp switch and the IP wiring harness junction block. Is the repair complete? | -- | System OK | -- |
26 | Connect a test lamp between cavity G 8 (BLK) in the IP wiring harness junction block connector and B+. Did the test light illuminate? | -- | Go to Step 28 | Go to Step 27 |
27 | Repair the open in CKT 150 (BLK) between the IP wiring harness junction block connector and ground G 200. Is the repair complete? | -- | System OK | -- |
28 | Measure the resistance in CKT 1697 (PPL) between cavity H 7 in the IP wiring harness junction block connector and cavity E 9 in the turn/hazard lamp switch connector with a J 39200 . Is the resistance greater than the specified value? | 1 ohms | Go to Step 29 | Go to Step 30 |
29 | Repair the open in CKT 1697 (PPL) between the IP wiring harness junction block connector and the turn/hazard lamp switch connector. Is the repair complete? | -- | System OK | -- |
30 | Replace the turn/hazard lamp flasher in the IP wiring harness junction block. Is the repair complete? | -- | System OK | -- |
