Ignition Switch Assembly - Assemble - Off Vehicle Column Shift
Tools Required
J 41352 Modular
Column Holding Fixture
Notice: Use the correct fastener in the correct location. Replacement fasteners
must be the correct part number for that application. Fasteners requiring
replacement or fasteners requiring the use of thread locking compound or sealant
are identified in the service procedure. Do not use paints, lubricants, or
corrosion inhibitors on fasteners or fastener joint surfaces unless specified.
These coatings affect fastener torque and joint clamping force and may damage
the fastener. Use the correct tightening sequence and specifications when
installing fasteners in order to avoid damage to parts and systems.
- Install the dimmer
and ignition switch mounting stud (4).
Tighten
Tighten the dimmer and ignition switch mounting stud to 4 N·m
(35 lb in).
- Install the ignition switch assembly (1) to the ignition
switch actuator assembly.
- Install the ignition switch assembly (1) onto the dimmer
and ignition switch mounting stud (4).
- Install the washer head screw (2) into the ignition switch
assembly (1).
- Tighten the washer head screw (2) finger tight.
- Install the hexagon nut (3) onto the dimmer and ignition
switch mounting stud (4)
- Tighten the hexagon nut (3) finger tight.
- Move the ignition switch
assembly slider (2) to the far right position.
- Move the ignition switch assembly slider (2) detent to
the left. This is the "OFF LOCK" position.
- Install a 3/32 inch drill bit into the hole on the ignition
switch assembly (1) to limit travel.
- Push against the ignition switch actuator assembly to limit all
the lash.
- Secure the washer head
screw (2) into the ignition switch assembly (1).
Tighten
Tighten the washer head screw to 4 N·m (35 lb in).
- Secure the hexagon nut (3) onto the dimmer and ignition
switch mounting stud (4).
Tighten
Tighten the hexagon nut to 4 N·m (35 lb in).
- Remove the 3/32 inch drill bit.
- Install the solenoid bracket (2).
- Install the 2 washer head screws (1).
Tighten
Tighten the screws to 4 N·m (35 lb in).
- Install the interlock solenoid assembly (7).
- Install the hex washer head screw (6).
Tighten
Tighten the screw to 4 N·m (35 lb in).
- Install the ball joint spring (5) to the interlock solenoid
assembly (7).
- Install the cable mounting clip from solenoid bracket (2).
- Install the cable assembly with ignition switch actuator assembly (4).
Remove the steering column and J 41352
from the vise.
Ignition Switch Assembly - Assemble - Off Vehicle Floor Shift
Tools Required
J 41352 Modular
Column Holding Fixture
Notice: Use the correct fastener in the correct location. Replacement fasteners
must be the correct part number for that application. Fasteners requiring
replacement or fasteners requiring the use of thread locking compound or sealant
are identified in the service procedure. Do not use paints, lubricants, or
corrosion inhibitors on fasteners or fastener joint surfaces unless specified.
These coatings affect fastener torque and joint clamping force and may damage
the fastener. Use the correct tightening sequence and specifications when
installing fasteners in order to avoid damage to parts and systems.
- Install the dimmer
and ignition switch mounting stud (4).
Tighten
Tighten the dimmer and ignition switch mounting stud to 4 N·m
(35 lb in).
- Install the ignition switch assembly (1) to the ignition
switch actuator assembly.
- Install the ignition switch assembly (1) onto the dimmer
and ignition switch mounting stud (4).
- Install the washer head screw (2) into the ignition switch
assembly (1).
- Tighten the washer head screw (2) finger tight.
- Install the hexagon nut (3) onto the dimmer and ignition
switch mounting stud (4)
- Tighten the hexagon nut (3) finger tight.
- Move the ignition switch
assembly slider (2) to the far right position.
- Move the ignition switch assembly slider (2) detent to
the left. This is the "OFF LOCK" position.
- Install a 3/32 inch drill bit into the hole on the ignition
switch assembly (1) to limit travel.
- Push against the ignition switch actuator assembly to limit all
the lash.
- Secure the washer head
screw (2) into the ignition switch assembly (1).
Tighten
Tighten the washer head screw to 4 N·m (35 lb in).
- Secure the hexagon nut (3) onto the dimmer and ignition
switch mounting stud (4).
Tighten
Tighten the hexagon nut to 4 N·m (35 lb in).
- Remove the 3/32 inch drill bit.
- Remove the steering column and J 41352
from the vise.