GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The engine coolant temperature (ECT) sensor is a variable resistor, that measures the temperature of the engine coolant. The powertrain control module (PCM) supplies 5 volts to the ECT signal circuit and a ground for the ECT low reference circuit. When the ECT is cold, the sensor resistance is high. When the ECT increases, the sensor resistance decreases. With high sensor resistance, the PCM detects a high voltage on the ECT signal circuit. With lower sensor resistance, the PCM detects a lower voltage on the ECT signal circuit. If the PCM detects an excessively low ECT signal voltage, which is a high temperature indication, DTC P0117 sets.

Conditions for Running the DTC

Engine run time is more than 10 seconds

OR

The engine run time is less than 10 seconds when IAT is less than 50°C (122°F).

Conditions for Setting the DTC

The ECT sensor temperature is more than 139°C (282°F) for more than 20 seconds.

Action Taken When the DTC Sets

    â€¢ The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
    â€¢ The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.

Conditions for Clearing the MIL/DTC

    â€¢ The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
    â€¢ A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
    â€¢ A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
    â€¢ Clear the MIL and the DTC with a scan tool.

Diagnostic Aids

    â€¢ An overheating condition may cause this DTC to set.
    â€¢ After starting the engine, the ECT should rise steadily to about 90°C (194°F) then stabilize when the thermostat opens.
    â€¢ Use the Temperature vs. Resistance table in order to test the ECT sensor at various temperature levels in order to evaluate the possibility of a skewed sensor. A skewed sensor could result in poor driveability concerns. Refer to Temperature Versus Resistance .
    â€¢ If the malfunction is not present at this time refer to DTC P1114 .
    â€¢ If the condition is suspected of being an intermittent, refer to Intermittent Conditions .

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. If DTC P0117 can only be repeated by duplicating the Failure Records, refer to Temperature vs Resistance. The table may be used to test the ECT sensor at various temperatures in order to evaluate the possibility of a shifted sensor that may be shorted above or below a certain temperature. If this is the case, replace the ECT sensor. If the ECT sensor appears to be OK, the malfunction is intermittent: refer to Diagnostic Aids.

  2. When testing ECT signal circuit for a short to ground, it may be necessary to check for continuity between all other PCM circuits.

DTC P0117- ECT Sensor Circuit Low Voltage

Step

Action

Values

Yes

No

Schematic Reference: Engine Controls Schematics

1

Did you perform the Diagnostic System Check-Engine Controls?

--

Go to Step 2

Go to Diagnostic System Check - Engine Controls

2

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. Observe the ECT sensor temperature display.

Does the scan tool indicate that the ECT sensor temperature is greater than the specified value?

138°C (280°F)

Go to Step 4

Go to Step 3

3

  1. Observe the Freeze Frame/Failure records data for this DTC.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text or as close to the Freeze Frame/Failure records data that you observed.

Does the DTC reset?

--

Go to Step 4

Go to Diagnostic Aids

4

  1. Disconnect the ECT sensor. Refer to Engine Coolant Temperature Sensor Replacement .
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, observe the ECT sensor temperature.

Does the scan tool indicate that the ECT sensor temperature is less than the specified value?

-38°C (-36°F)

Go to Step 6

Go to Step 5

5

  1. Turn off the ignition.
  2. Disconnect the PCM. Refer to Powertrain Control Module Replacement .
  3. Test the signal circuit of the ECT sensor for a short to ground or a short to the ECT reference low circuit. Refer to Circuit Testing , and refer to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 8

Go to Step 7

6

Replace the ECT sensor. Refer to Engine Coolant Temperature Sensor Replacement .

Did you complete the replacement?

--

Go to Step 8

--

7

Replace the PCM. Refer to Powertrain Control Module Replacement .

Did you complete the replacement?

--

Go to Step 8

--

8

  1. Use the scan tool in order to clear the DTCs.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC run and pass?

--

Go to Step 9

Go to Step 2

9

With a scan tool observe the Stored information, Capture Info.

Does the scan tool display any DTCs that you have not diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List

System OK