Important: Whenever the transmission 20-way connector is disconnected and the engine is running, multiple DTCs will set. Be sure to clear these codes when you are finished with this procedure.

Important: This procedure tests the Automatic Transmission Fluid Pressure (TFP) Manual Valve Position Switch circuits and the Automatic Transmission Fluid Temperature (TFT) Sensor circuit. Do not use this procedure to test other Automatic Transmission circuits. Refer to 4L60-E Automatic Transmission Wiring Harness Check

1. Install the J 39775 jumper harness on the transmission side of the 20-way connector.
2. Using the J 39200 digital multimeter (DMM) and the J 35616-A connector test adapter kit, measure the resistance from terminal N to the transmission case.

Is the resistance greater than the specified value?

50 K ohms

Go to Step 3

Go to Step 2

1. Disconnect the TFP manual valve position switch from the automatic transmission (A/T) wiring harness assembly.
2. Measure the resistance from terminal C of the TFP manual valve position switch to the switch housing.

Is the resistance greater than the specified value?

50 K ohms

Go to Step 16

Go to Step 19

Measure the resistance from terminal R to the transmission case.

Is the resistance less than the specified value?

200 ohms

Go to Step 5

Go to Step 4

1. Disconnect the TFP manual valve position switch from the A/T wiring harness assembly.
2. Measure the resistance from terminal E of the TFP manual valve position switch to the switch housing.

Is the resistance less than the specified value?

200 ohms

Go to Step 16

Go to Step 19

Measure the resistance from terminal P to the transmission case.

Is the resistance greater than the specified value?

50 K ohms

Go to Step 7

Go to Step 6

1. Disconnect the TFP manual valve position switch from the A/T wiring harness assembly.
2. Measure the resistance from terminal D of the TFP manual valve position switch to the switch housing.

Is the resistance greater than the specified value?

50 K ohms

Go to Step 16

Go to Step 19

1. Start the engine.
2. Allow the engine to idle.
3. Set the parking brake.
4. Place the gear selector in REVERSE.
5. Measure the resistance from terminal N to the transmission case.

Is the resistance less than the specified value?

200 ohms

Go to Step 8

Go to Step 16

1. Place the gear selector in Low (D1).
2. Measure the resistance from terminal N to the transmission case.

Is the resistance less than the specified value?

200 ohms

Go to Step 9

Go to Step 16

1. Place the gear selector in Manual Third (D3).
2. Measure the resistance from terminal R to the transmission case.

Is the resistance greater than the specified value?

50 K ohms

Go to Step 10

Go to Step 16

1. Place the gear selector in DRIVE (D4).
2. Measure the resistance from terminal P to the transmission case.

Is the resistance less than the specified value?

200 ohms

Go to Step 11

Go to Step 16

1. Place the gear selector in Manual Second (D2).
2. Measure the resistance from terminal P to the transmission case.

Is the resistance greater than the specified value?

50 K ohms

Go to Step 12

Go to Step 16

1. Turn the ignition OFF.

Important: The resistance of the TFT sensor is temperature dependent, and therefore varies far more than any other device. Refer to Transmission Fluid Temperature Sensor in Electronic Component Description .

2. Measure the resistance from terminal L to terminal M (TFT Sensor) of the J 39775 .

Is the resistance within the specified range?

3088-3942 ohms @ 20°C (68°F)

159-198 ohms @ 100°C (212°F)

Go to Step 13

Go to Step 14

1. Measure the resistance from terminal L to the transmission case.
2. Measure the resistance from terminal M to the transmission case.

Are both resistances greater than the specified value?

10 M ohms

System OK

Go to Step 14

1. Disconnect the TFP manual valve position switch from the A/T wiring harness assembly.

Important: The resistance of the TFT sensor is temperature dependent, and therefore varies far more than any other device. Refer to Transmission Fluid Temperature Sensor in Electronic Component Description .

2. Using the J 39200 DMM, measure the resistance between terminal A and terminal B of the TFP manual valve position switch (TFT sensor).

Is the resistance within the specified range?

3088-3942 ohms @ 20°C (68°F)

159-198 ohms @ 100°C (212°F)

Go to Step 15

Go to Step 19

1. Measure the resistance from TFP manual valve position switch terminal A to the transmission case.
2. Measure the resistance from TFP manual valve position switch terminal B to the transmission case.

Are both resistances greater than the specified value?

10 M ohms

Go to Step 16

Go to Step 19

Inspect for high resistance or a short:

Was a high resistance or a short found?

--

Go to Step 1

Go to Step 17

1. Disconnect the TFP manual valve position switch from the A/T wiring harness assembly.
2. Inspect the following circuits for an open or short:

•	Circuit 1224

•	Circuit 1225

•	Circuit 1226

•	Circuit 1227

Was an open or shorted condition found?

--

Go to Step 18

Go to Step 19

Replace the A/T wiring harness assembly.

Refer to Torque Converter Clutch Pulse Width Modulation Solenoid, Torque Converter Clutch Solenoid, and Wiring Harness Replacement.

Is the replacement complete?

--

Go to Step 1

--

Replace the TFP manual valve position switch.

Refer to Valve Body and Pressure Switch Replacement .

Is the replacement complete?

--

Go to Step 1

--