DEFINITION: Upward or downward controls are inoperative for the rear vertical motor. Horizontal and front tilt motors operate normally. Either driver's side or passenger's side seat.

Were you sent here from the Power Seat System Diagnostic System Check?

--

Go to Step 2

Go to Power Seats System Check

1. Disconnect the LH or RH seat adjuster switch connector.
2. Connect a jumper wire from:

•	LEFT SIDE = The seat adjuster switch connector terminal 24 to ground.

•	RIGHT SIDE = The seat adjuster switch connector terminal 3 to ground.

Does the seat motor move?

--

Go to Step 3

Go to Step 5

Connect the jumper wire from:

Does the seat motor move?

--

Go to Step 4

Go to Step 7

Replace the RH or LH seat adjuster switch. Refer to Power Seat Switch Replacement .

Is the repair complete?

--

Go to Power Seats System Check

--

1. Disconnect the RH or LH seat relay center connector C1.
2. Use a DMM to measure CKT 1521 for continuity between the seat relay center connector C1 terminal 12 and the seat adjuster switch connector:

•	LEFT SIDE = Terminal 24.

•	RIGHT SIDE = Terminal 3.

Is CKT 1521 continuous between these two connectors?

--

Go to Step 9

Go to Step 6

Locate and repair an open or a high resistance in CKT 1521.

Is the repair complete?

--

Go to Power Seats System Check

--

1. Disconnect the RH or LH seat relay center connector C1.
2. Use a DMM to measure CKT 1519 for continuity between the seat relay center connector C1 terminal 1 and the seat adjuster switch connector:

•	LEFT SIDE = Terminal 3.

•	RIGHT SIDE = Terminal 24.

Is CKT 1519 continuous between these two connectors?

--

Go to Step 9

Go to Step 8

Locate and repair an open or a high resistance in CKT 1519.

Is the repair complete?

--

Go to Power Seats System Check

--

1. Disconnect the RH or LH seat relay center connector C2 and C3.
2. Using two jumper wires, perform the following test:

•	Connect a jumper wire between battery power and the seat relay center connector C2 terminal F.

•	Connect a second jumper wire between ground and the seat relay center connector C3 terminal D.

3. Now reverse the jumper wires as follows:

•	Connect the jumper wire between battery power and the seat relay center connector C3 terminal D.

•	Connect the second jumper wire between ground and the seat relay center connector C2 terminal F.

Does the rear vertical motor operate in both directions during each of these conditions?

--

Go to Step 11

Go to Step 10

1. Disconnect the RH or LH lower seat motor connector C1.
2. Use a DMM to measure CKT 282 for continuity between the seat relay center connector C2 terminal F and the seat motor connector C1 terminal E.

Is CKT 282 continuous between these two connectors?

--

Go to Step 12

Go to Step 13

Replace the RH or LH seat relay center.

Is the repair complete?

--

Go to Power Seats System Check

--

Locate and repair an open or a high resistance in CKT 282.

Is the repair complete?

--

Go to Power Seats System Check

--

Use a DMM to measure CKT 283 for continuity between the seat relay center connector C3 terminal D and the seat motor connector C1 terminal F.

Is CKT 283 continuous between these two connectors?

--

Go to Step 14

Go to Step 15

Locate and repair an open or a high resistance in CKT 283.

Is the repair complete?

--

Go to Power Seats System Check

--

Check carefully for any binding of the rear vertical seat motor and linkage. If OK, replace the RH or LH rear vertical seat motor. Refer to Front Seat Adjuster Motor Replacement .

Is the repair complete?

--

Go to Power Seats System Check

--