1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
2. Remove the transmission oil pan and filter. Refer to Automatic Transmission Fluid and Filter Replacement .
3. Remove the control valve body. Refer to Valve Body and Pressure Switch Replacement .
4. Remove the accumulator cover retaining bolts.
5. Remove the 1-2 accumulator cover and pin assembly.



6. Disassemble the 1-2 accumulator assembly.

6.1.	Blow compressed air into the 1-2 accumulator cover, as shown, to remove the 1-2 accumulator piston.

6.2.	Remove the 1-2 accumulator inner and outer springs.

7. Inspect the 1-2 accumulator inner and outer springs for cracks.



8. Remove the 1-2 accumulator piston seal (1) from the 1-2 accumulator piston.
9. Inspect the 1-2 accumulator piston for the following defects:

•

Porosity

•

Cracks

•

Scoring

•	Nicks and scratches




10. Inspect the 1-2 accumulator cover for the following defects:

•

Porosity

•

Cracks

•

Scoring

•	Nicks and scratches




11. Remove the spacer plate support retaining bolts.
12. Remove the spacer plate support.



13. Remove the spacer plate to valve body gasket, the spacer plate and the spacer plate to transmission case gasket.



14. Remove the 3-4 accumulator spring and the 3-4 accumulator piston.
15. Inspect the 3-4 accumulator spring for cracks.



16. Remove the 3-4 accumulator piston seal (1) from the 3-4 accumulator piston.
17. Inspect the 3-4 accumulator piston for the following defects:

•

Porosity

•

Cracks

•

Scoring

•	Nicks and scratches

Tools Required:

1. Install a new 3-4 accumulator piston seal (1) to the 3-4 accumulator piston.



2. Install the 3-4 accumulator piston onto the pin in the transmission case.

Ensure that the 3-4 accumulator piston legs face away from the transmission case.

3. Install the 3-4 accumulator piston spring.



4. Install the J 25025-B to the transmission case.
5. Install the spacer plate to transmission case gasket and the spacer plate to valve body gasket to the spacer plate; use the J 36850 in order to retain the gaskets to the spacer plate.

•	The case gasket is identified by a C.

•	Be sure to place the case gasket on the transmission case side of the spacer plate.

•	The valve body gasket is identified by a V.

•	Be sure to place the valve body gasket on the valve body side of the spacer plate.

6. Install the spacer plate to transmission case gasket, the spacer plate and the spacer plate to valve body gasket assembly to the transmission case.




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

7. Install the spacer plate support and the spacer plate support retaining bolts.

Tighten
Tighten the spacer plate support retaining bolts to 11 N·m (97 lb in).




8. Install a new 1-2 accumulator piston seal (1) to the 1-2 accumulator piston.



9. Install the 1-2 accumulator inner and outer springs to the 1-2 accumulator cover.
10. Install the 1-2 accumulator piston onto the pin in the 1-2 accumulator cover.

Ensure that the piston legs face the accumulator cover.




11. Install the 1-2 accumulator cover and the accumulator cover retaining bolts.

Tighten
Tighten the accumulator cover retaining bolts to 11 N·m (97 lb in).

12. Remove the J 25025-B from the transmission case.
13. Install the control valve body. Refer to Valve Body and Pressure Switch Replacement .
14. Install the transmission oil pan and filter. Refer to Automatic Transmission Fluid and Filter Replacement .
15. Lower the vehicle.