Turn Signal Lamps Inoperative All
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Were you sent here from the Lighting Systems Diagnostic System Check? | -- | ||
2 | Inspect the HAZT/SIG fuse #15 for an open. Is the fuse open? | -- | ||
3 | Repair the short to ground in circuit 1739. Is the repair complete? | -- | -- | |
4 |
Does the test light illuminate? | -- | ||
5 | Repair the open or high resistance in circuit 1739. Is the repair complete? | -- | -- | |
6 |
Do the left and right turn signals illuminate? | -- | ||
7 | Test and repair the hazard warning switch jumper harness circuits 1739 and 16 for an open or high resistance, if OK replace the hazard warning switch. Refer to Hazard Warning Switch Replacement . Is the repair complete? | -- | -- | |
8 |
Is the test light flashing? | -- | ||
9 | Repair the open or high resistance in circuit 16. Is the repair complete? | -- | -- | |
10 | With the ignition ON connect a fused jumper wire from the C209 harness connector terminals D to G. Are the left front turn signals flashing? | -- | Go to Symptoms | |
11 | With the ignition ON connect a fused jumper wire from the C209 harness connector terminals D to F. Are the right front turn signals flashing? | -- | Go to Symptoms | |
12 | With the ignition ON connect a fused jumper wire from the C209 harness connector terminals D to C. Are the left rear turn signals flashing? | -- | Go to Symptoms | |
13 | With the ignition ON connect a fused jumper wire from the C209 harness connector terminals D to B. Are the right rear turn signals flashing? | -- | Go to Symptoms | |
14 | Replace the turn signal switch. Refer to Multifunction Turn Signal Lever Replacement - On Vehicle . Is the repair complete? | -- | -- | |
15 |
Did you correct the condition? | -- | System OK |
Turn Signal Lamps Inoperative Left Front
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Has the Lighting Systems Diagnostic System Check been performed? | -- | ||
2 |
Is the test light flashing? | -- | ||
3 | Test and repair circuit 14 for an open or high resistance. Did you find and correct the condition? | -- | ||
4 | Replace the multifunction turn signal lever. Refer to Multifunction Turn Signal Lever Replacement - On Vehicle Is the repair complete? | -- | -- | |
5 | Connect a fused jumper wire from the circuit 14 to the circuit 1314 relay terminals in the instrument panel electrical center. With the ignition and the left turn signal switches ON, do the left front turn signals operate? | -- | ||
6 | Replace the DRL L Micro Relay #40. Is the repair complete? | -- | -- | |
7 |
Is the resistance within the specified values? | 0-2 ohms | ||
8 | Using a DMM test the resistance of circuit 150 from the bulb connector to ground. Is the resistance within the specified values? | 0-2 ohms | ||
9 | Repair the open or high resistance in circuit 1314. Is the repair complete? | -- | -- | |
10 | Repair the open or high resistance in circuit 150. Is the repair complete? | -- | -- | |
11 | Replace the inoperative turn signal bulb. Refer to Park/Turn Signal/Side Marker Lamp Bulb Replacement . Is the repair complete? | -- | -- | |
12 |
Did you correct the condition? | -- | System OK |
Turn Signal Lamps Inoperative Right Front
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Has the Lighting Systems Diagnostic System Check been performed? | -- | ||
2 |
Is the test light flashing? | -- | ||
3 | Test and repair circuit 15 for an open or high resistance. Did you find and correct the condition? | -- | ||
4 | Replace the multifunction turn signal lever. Refer to Multifunction Turn Signal Lever Replacement - On Vehicle Is the repair complete? | -- | -- | |
5 | Connect a fused jumper wire from the circuit 15 to the circuit 1315 relay terminals in the instrument panel electrical center. With the ignition and the right turn signal switches ON, do the right front turn signals operate? | -- | ||
6 | Replace the DRL R Micro Relay #38. Is the repair complete? | -- | -- | |
7 |
Is the resistance within the specified values? | 0-2 ohms | ||
8 | Using a DMM test the resistance of circuit 150 from the bulb connector to ground. Is the resistance within the specified values? | 0-2 ohms | ||
9 | Repair the open or high resistance in circuit 1315. Is the repair complete? | -- | -- | |
10 | Repair the open or high resistance in circuit 150. Is the repair complete? | -- | -- | |
11 | Replace the inoperative turn signal bulb. Refer to Park/Turn Signal/Side Marker Lamp Bulb Replacement . Is the repair complete? | -- | -- | |
12 |
Did you correct the condition? | -- | System OK |
Turn Signal Lamps Inoperative Left Rear
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Has the Lighting Systems Diagnostic System Check been performed? | -- | ||
2 |
Is the test light flashing? | -- | ||
3 | Repair the open or high resistance in circuit 18. Is the repair complete? | -- | -- | |
4 | With the ignition and left turn signal ON, connect the test light from the bulb connector terminals A to G. Is the test light flashing? | -- | ||
5 | Repair the open or high resistance in circuit 150. Is the repair complete? | -- | -- | |
6 | Replace the inoperative turn signal bulbs as necessary. Is the repair complete? | -- | -- | |
7 | Operate the system in order to verify the repair. Did you correct the condition? | -- | System OK |
Turn Signal Lamps Inoperative Right Rear
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Has the Lighting Systems Diagnostic System Check been performed? | -- | ||
2 |
Is the test light flashing? | -- | ||
3 | Repair the open or high resistance in circuit 19. Is the repair complete? | -- | -- | |
4 | With the ignition and right turn signal ON, connect the test light from the bulb connector terminals A to G. Is the test light flashing? | -- | ||
5 | Repair the open or high resistance in circuit 150. Is the repair complete? | -- | -- | |
6 | Replace the inoperative turn signal bulbs as necessary. Is the repair complete? | -- | -- | |
7 | Operate the system in order to verify the repair. Did you correct the condition? | -- | System OK |
