Circuit Description
The BCM monitors the LF turn signal circuit in order to determine the status of the turn signal switch. If the BCM detects an oscillating voltage on the LH turn signal monitor circuit, the BCM interprets this as a LF turn signal ON request from the turn signal switch. The BCM will de-energize the LH DRL relay, which will disable the LF turn signal lamp (which is ON for the DRL), thus allowing the LF turn signal to flash. If the BCM does not detect an oscillating voltage on the LH turn signal monitor circuit, the BCM interprets this as the LF turn signal being OFF. The BCM will then energize the LH DRL relay and continue normal DRL operation. The BCM monitors the LF turn signal monitor circuit and determines how long voltage is applied. If the voltage is applied for longer than expected, a malfunction is present and a DTC will set.
Conditions for Setting the DTC
| • | The BCM detects continuous battery voltage on the LH turn signal monitor circuit. |
| • | The condition must be present for longer than 5 seconds. |
Action Taken When the DTC Sets
| • | Stores a DTC B2583 in the BCM memory. |
| • | No driver warning message will be displayed for this DTC. |
Conditions for Clearing the DTC
| • | This DTC requires an ignition cycle in order to change from current to history. |
| • | The BCM no longer detects continuous battery voltage on the LH turn signal monitor circuit for longer than 5 seconds. |
| • | A history DTC will clear after 50 consecutive ignition cycles if the condition for the malfunction is no longer present. |
| • | Use the IPC clearing DTCs feature. |
| • | Use a scan tool. |
Diagnostic Aids
| • | The following conditions may cause an intermittent malfunction: |
| - | There is an intermittent short to voltage in the LH turn signal monitor circuit. |
| - | The turn signal switch or the hazard switch is shorted internally or is sticking. |
| • | The BCM needs to detect voltage oscillations on the LH turn signal monitor circuit in order to de-energize the LH DRL relay. If the BCM detects continuous voltage on the LH turn signal monitor circuit, the BCM interprets this as a short to voltage. The BCM will continue with normal DRL operation, and the LF turn signal will remain inoperative. |
| • | If the DTC is a history DTC, the problem may be intermittent. Perform the tests shown while moving related wiring and connectors. This can often cause the malfunction to occur. Refer to Intermittents and Poor Connections . |
Test Description
The number(s) below refer to the step number(s) on the diagnostic table.
-
Tests if a DTC B2578 is stored in the BCM. If both the LH and LH turn signal monitor DTCs are stored, test the hazard switch and related circuits for a short to voltage.
-
Tests if the BCM is receiving oscillating voltage on the LH turn signal monitor circuit. If the test light is ON steady, the BCM will set a DTC B2583.
-
Tests if the BCM is receiving oscillating voltage on the LH turn signal monitor circuit. If the test light is ON steady, the BCM will set a DTC B2583.
-
Tests if the turn signal switch or related circuits are shorted to voltage.
-
Tests if the hazard switch or related circuits are shorted to voltage.
-
Tests if the instrument panel cluster turn signal indicator is shorted to voltage.
-
Tests if the body control module is shorted to voltage.
-
When the BCM is replaced, use a scan tool to perform the BCM RPO Reprogram procedure. Refer to Body Control Module (BCM) Programming/RPO Configuration .
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Did you perform the BCM Diagnostic System Check? | -- | Go to Step 2 | |
Does the scan tool display DTC B2583? | -- | Go to Step 10 | Go to Step 3 | |
Does the test lamp turn ON and OFF with the LH turn signals? | -- | Go to Step 13 | Go to Step 4 | |
Does the test lamp remain illuminated? | -- | Go to Step 5 | ||
Disconnect the turn signal switch. Does the test lamp remain illuminated? | -- | Go to Step 6 | Go to Step 9 | |
Disconnect the hazard switch. Does the test lamp remain illuminated? | -- | Go to Step 7 | Go to Step 10 | |
Disconnect the instrument panel cluster. Does the test lamp remain illuminated? | -- | Go to Step 8 | Go to Step 11 | |
Disconnect the body control module. Does the test lamp remain illuminated? | -- | Go to Step 12 | Go to Step 14 | |
9 | Repair a short to voltage in the turn signal switch circuit. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 15 | -- |
10 | Repair a short to voltage in the hazard switch circuit. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 15 | -- |
11 | Repair a short to voltage in the instrument panel turn signal indicator circuit. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 15 | -- |
12 | Repair a short to voltage in the turn signal monitor circuit. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 15 | -- |
13 | Replace the LH DRL relay. Did you complete the replacement? | -- | Go to Step 15 | -- |
|
Important: Perform the BCM RPO Reprogram procedure. Refer to Body Control Module (BCM) Programming/RPO Configuration . Replace the BCM. Refer to Body Control Module Replacement . Did you complete the replacement? | -- | Go to Step 15 | -- | |
15 |
Does the DTC reset? | -- | Go to Step 2 | System OK |
