Circuit Description
The LH door switch circuit provides input to the LH Door Control Module (LDCM) when the LH mirror switch is pressed. This input allows the LDCM to detect a mirror position request. The LDCM provides both power and ground to the mirror switches. When the mirror down switch is pressed, a ground is supplied through the mirror up switch to the mirror up switch input which is pulled low. When the LDCM detects low voltage on the mirror up switch input, and the driver mirror was selected, the LDCM will command the driver mirror to operate UP. When the LDCM detects low voltage on the mirror down switch input, the LDCM will command the driver mirror to operate DOWN. If the passenger mirror was selected, the LDCM controls RH mirror functions by sending mirror control messages to the RH Door Control Module (RDCM) on the serial data line. The LDCM monitors both the mirror down and mirror up switch signal circuits and determines how long a ground (switch pressed) has been applied. If the ground is applied for longer than expected, a malfunction is present and a DTC will set.
Conditions for Setting the DTC
| • | The LDCM detects a low voltage level (short to ground) at the mirror down switch signal circuit. |
| • | Condition must be present for 20 seconds. |
Action Taken When the DTC Sets
| • | Stores a history DTC B2234 in the LDCM memory. |
| • | This DTC can only be set as a history code even if the malfunction is current. |
| • | No driver warning message will be displayed for this DTC. |
Conditions for Clearing the DTC
| • | The LDCM no longer detects a low voltage level (short to ground) at the mirror down switch signal circuit for longer than 20 seconds. |
| • | Use the IPC clearing DTCs feature. |
| • | Use a scan tool. |
Diagnostic Aids
| • | The following conditions may cause an intermittent malfunction: |
| - | There is an intermittent short to ground in the mirror dowm witch signal circuit. |
| - | The mirror down switch is shorted to ground internally or is sticking. |
| - | The mirror down switch was pressed for longer than 20 seconds. |
| • | If mirror down switch signal circuit is shorted to ground or the mirror down switch is stuck closed, the mirror will operate DOWN only. |
| • | Using a scan tool, select LDCM inputs and monitor the Mirror Down Switch status. If the scan tool displays ACTIVE, disconnect the LH mirror switch and check if the Mirror Down Switch status changes to INACTIVE. If the Mirror Down Switch status changed then replace the LH mirror switch. If the Mirror Down Switch status did not change, then check mirror down switch signal circuit for a short to ground. |
| • | If the DTC does not reset after the code is cleared, then the problem may be intermittent. Perform the tests shown while moving related wiring and connectors. This can often cause the malfunction to occur. Refer to Intermittents and Poor Connections . |
Test Description
The number(s) below refer to the step number(s) on the diagnostic table.
-
Tests for the normal state of the mirror down switch using a scan tool. The scan tool will display the normal state as INACTIVE, and ACTIVE when the switch is activated.
-
Tests if the LH DCM is able to detect a change in mirror down switch state. The scan tool will display the normal state as INACTIVE, and ACTIVE when the switch is activated.
-
Tests for a stuck or shorted mirror down switch. If the mirror down switch is stuck or shorted, the state will change from ACTIVE to INACTIVE when the mirror down switch is disconnected.
-
Tests for a short to ground in the mirror down switch signal circuit.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Power Door Systems Diagnostic System Check? | -- | Go to Step 2 | |
Does the scan tool display INACTIVE? | -- | Go to Step 3 | Go to Step 4 | |
Does the Mirror Down Switch parameter change state? | -- | Go to Diagnostic Aids | Go to Step 4 | |
Does the scan tool display INACTIVE? | -- | Go to Step 7 | Go to Step 5 | |
Test the signal circuit of the mirror down switch for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 6 | |
6 | Inspect for poor connections at the harness connector of the LH DCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 8 |
7 | Inspect for poor connections at the harness connector of the LH door switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 9 |
8 | Replace the LH DCM. Refer to Door Control Module Replacement . Did you complete the replacement? | -- | Go to Step 10 | -- |
9 | Replace the LH door switch. Refer to Front Door Switch Replacement . Did you complete the replacement? | -- | Go to Step 10 | -- |
10 |
Does the DTC reset? | -- | Go to Step 2 | System OK |
