For 1990-2009 cars only
1-2 Shift Error: Displays a range of -6.38 to +6.38 seconds. This parameter
is the difference between the desired 1-2 shift time and the actual 1-2 shift
time. A positive number indicates a firm or fast shift (the actual shift
time was shorter than the desired shift time). A negative number indicates
a soft or slow shift (the actual shift time was longer than the desired shift
time). This value is only accurate if the shift was adaptable.
1-2 Shift Time: Displays a range of 0.00-6.38 seconds. This parameter is the actual time of the last 1-2 shift. The shift time is based on the engine RPM drop after the commanded 1-2 shift. This value is only accurate if the shift was adaptable.
1-2 Sol.: Displays ON or OFF. This parameter is the commanded state of the 1-2 shift solenoid valve. ON represents a commanded energized state (current is flowing through the solenoid). OFF represents a non-commanded state (current is not flowing through the solenoid).
1-2 Sol. Open/Short to GND: Displays Yes or No. This parameter indicates if an open or short to ground exists in the 1-2 shift solenoid valve feedback signal to the PCM. This parameter is valid only when the 1-2 shift solenoid is commanded OFF.
1-2 Sol. Short to Volts: Displays Yes or No. This parameter indicates if a short to voltage exists in the 1-2 shift solenoid valve feedback signal to the PCM. This parameter is valid only when the 1-2 shift solenoid is commanded ON.
1-2 Tap Cell (4-16): Displays kPa or psi. This parameter displays the amount of pressure varied from a calibrated base line pressure for shifts. Each TAP Cell is based on a calibrated shift torque value. Each TAP Cell value is calculated from the last shift time. This cell pressure is used in addition to the calibrated base line pressure to adjust the apply of a clutch or band during the next shift.
2-3 Shift Error: Displays a range of -6.38 to +6.38 seconds. This parameter is the difference between the desired 2-3 shift time and the actual 2-3 shift time. A positive number indicates a firm or fast shift (the actual shift time was shorter than the desired shift time). A negative number indicates a soft or slow shift (the actual shift time was longer than the desired shift time). This value is only accurate if the shift was adaptable.
2-3 Shift Time: Displays a range of 0.00-6.38 seconds. This parameter is the actual time of the last 2-3 shift. The shift time is based on the engine RPM drop after the commanded 2-3 shift. This value is only accurate if the shift was adaptable.
2-3 Sol.: Displays ON or OFF. This parameter is the commanded state of the 2-3 shift solenoid valve. ON represents a commanded energized state (current is flowing through the solenoid). OFF represents a non-commanded state (current is not flowing through the solenoid).
2-3 Sol. Open/Short to GND: Displays Yes or No. This parameter indicates if an open or short to ground exists in the 2-3 shift solenoid valve feedback signal to the PCM. This parameter is valid only when the 2-3 shift solenoid is commanded OFF.
2-3 Sol. Short to Volts: Displays Yes or No. This parameter indicates if a short to voltage exists in the 2-3 shift solenoid valve feedback signal to the PCM. This parameter is valid only when the 2-3 shift solenoid is commanded ON.
2-3 Tap Cell (4-16): See 1-2 Tap Cell (4-16)
3-2 Downshift Sol.: Displays On or Off. This parameter indicates if the 3-2 shift solenoid valve assembly is currently commanded On or Off. The solenoid commanded state is based on the transmission temperature and the commanded gear. The solenoid will change states during a 3-2 downshift to regulate the appropriate pressure.
3-2 Sol. Open/Short to GND: Displays Yes or No. This parameter indicates if an open or short to ground exists in the 3-2 shift solenoid valve assembly feedback signal to the PCM. This parameter is valid only when the 3-2 shift solenoid is commanded OFF.
3-2 Sol. Short to Volts: Displays Yes or No. This parameter indicates if a short to voltage exists in the 3-2 shift solenoid valve assembly feedback signal to the PCM. This parameter is valid only when the 3-2 shift solenoid is commanded ON.
3-4 Shift Error: Displays a range of -6.38 to +6.38 seconds. This parameter is the difference between the desired 3-4 shift time and the actual 3-4 shift time. A positive number indicates a firm or fast shift (the actual shift time was shorter than the desired shift time). A negative number indicates a soft or slow shift (the actual shift time was longer than the desired shift time). This value is only accurate if the shift was adaptable.
3-4 Shift Time: Displays a range of 0.00-6.38 seconds. This parameter is the actual time of the last 3-4 shift. The shift time is based on the engine RPM drop after the commanded 3-4 shift. This value is only accurate if the shift was adaptable.
A/C Clutch: Displays On or Off. This parameter indicates the commanded state of the A/C control relay. The clutch should be engaged when On displays.
Cruise: Displays Enabled or Disabled. This parameter indicates whether the PCM is allowing cruise operation. The PCM has the ability to disable cruise control under certain conditions.
Current Gear: Displays 1, 2, 3 or 4. This parameter indicates the current commanded state of the shift solenoids.
Current TAP (Transmission Adaptive Pressure) Cell: The scan tool displays cells 4-16. This parameter indicates the current TAP cell in use for transmission line pressure adaptation. The cells are based on engine torque. The higher the engine torque, the higher the current TAP cell. The last cell used will remain displayed until the next adaptable upshift occurs.
ECT (Engine Coolant Temperature): Displays a range of -40°C to 151°C (-40°F to 304°F). This parameter is the input signal of the engine coolant temperature sensor. The engine coolant temperature is high (151°C) when the signal voltage is low (0 V), and the engine coolant temperature is low (-40°) when the signal voltage is high (5 V).
Engine Run Time: Displays a range of 0:00:00-18:12:15 hr/min/sec. This parameter measures how long the engine has been operating. When the ignition switch is turned OFF, the value is reset to zero.
Engine Speed: Displays a range of 0-8192 RPM. This parameter indicates the rotational speed of the engine expressed as revolutions per minute.
Engine Torque: Displays a range of 0-9999 lbs ft. This parameter indicates the amount of torque that is delivered from the engine.
Estimated Gear Ratio: Displays a range of 0.00:1-8.00:1. This parameter indicates the estimated turbine speed divided by the transmission output speed. Estimated turbine speed is calculated from engine speed and engine torque.
Ignition Voltage: Displays a range of 0.0-25.5 V. This represents the system voltage measured by the PCM at it's ignition feed.
Last Shift Time: Range 0.00-6.38 seconds. This parameter is the actual shift time of the last shift.
PC Sol. Actual Current: Displays a range of 0.00-1.10 amps. This parameter is the actual current of the pressure control solenoid circuit at the control module. Zero amp (no current flow) indicates actual higher line pressure. Actual lower line pressure is indicated by 1.1 amps (high current flow).
PC Sol. Duty Cycle: Displays a range of 0-100%. This parameter is the commanded state of the pressure control solenoid expressed as a percent of energized ON time. Zero percent indicates zero ON time (non-energized) or no current flow. Approximately 60% at idle indicates maximum ON time (energized) or high current flow.
PC Ref. (Reference) Current: Displays a range of 0.00-1.10 amps. This parameter is the commanded current of the pressure control solenoid circuit. Zero amp (no current flow) indicates commanded higher line pressure. Commanded lower line pressure is indicated by 1.1 amps (high current flow).
Speed Ratio: Displays a range of 0.00:1-8.00:1. This parameter indicates engine speed divided by transmission output speed. This value is used to estimate transmission gear ratio.
TCC Brake Switch: Displays Open or Closed. This parameter indicates the state of the brake switch circuit input. Open indicates a zero voltage input (brake switch open, brake pedal applied). Closed indicates a B+ voltage input (brake switch closed, brake pedal released).
TCC Duty Cycle: Displays a range of 0-100%. This parameter is the commanded percentage of ON time of the TCC PWM solenoid. Approximately 90% represents an ON (energized) commanded state. Zero percent represents an OFF (non-energized) commanded state. This commanded state is applied at a vehicle speed between approximately 0-16 km/h (0-10 mph).
TCC Duty Cycle Open/Short to GND: Displays Yes or No. This parameter indicates whether an open or a short to ground exists in the TCC PWM solenoid valve feedback signal to the PCM. This parameter is valid only when the TCC PWM solenoid is commanded OFF (duty cycle is 0%).
TCC Duty Cycle Short to Volts: Displays Yes or No. This parameter indicates whether a short to voltage exists in the TCC PWM solenoid valve feedback signal to the PCM. This parameter is valid only when the TCC PWM solenoid is commanded ON (duty cycle is at maximum).
TCC Enable: Displays Yes or No. This parameter is the commanded state of the TCC solenoid. Yes indicates a commanded energized state (current is flowing through the solenoid). No indicates a commanded non-energized state (current is not flowing through the solenoid). This commanded state occurs at various vehicle speeds between applications.
TCC Enable Open/Short to GND: Displays Yes or No. This parameter indicates whether an open or a short to ground exists in the TCC solenoid valve feedback signal to the PCM. This parameter is valid only when the TCC solenoid is commanded OFF.
TCC Enable Short to Volts: Displays Yes or No. This parameter indicates whether a short to voltage exists in the TCC solenoid valve feedback signal to the PCM. This parameter is valid only when the TCC solenoid is commanded ON.
TCC (Torque Converter Clutch) Slip Speed: Displays a range of -4080 to 4079 RPM. This parameter is the difference between transmission output speed and engine speed. A negative value indicates that the engine speed is less than the output speed (deceleration). A positive value indicates that the engine speed is greater than the output speed (acceleration). A value of zero indicates that the engine speed is equal to the output speed (TCC applied).
TFT (Transmission Fluid Temperature) Sensor: Displays a range of 0.00-5.00 V. When the transmission fluid is cold, the sensor resistance is high and the PCM will sense high signal voltage. As the transmission fluid temperature warms to a normal operating temperature, the sensor resistance becomes less and the voltage decreases.
TFP Sw.: Displays Park/Neutral, Reverse, Drive4, Drive3, Drive2, Drive1 or Invalid. This parameter is the decoded status of the three A/B/C inputs from the automatic transmission fluid pressure manual valve position switch. Invalid is displayed when the PCM does not recognize a valid combination of inputs.
TFP Sw. A/B/C: Displays HI/LOW, HI/LOW, HI/LOW. This parameter indicates the status of the three inputs from the Automatic Transmission Fluid Pressure Manual Valve Position Switch Assembly to the PCM. LOW represents a 0 voltage signal. HI represents an ignition voltage signal.
Torque Converter Efficiency - (Ratio): Displays a ratio of .00:1-2:1. The ratio is calculated by multiplying the speed ratio by a value related to the "K factor" of the torque converter. The "K factor" is the looseness or tightness of the torque converter for a given torque. The nearer the torque converter is to full coupling (i.e. 1:1) the closer the torque converter efficiency number will be to 1.
TP Indicated Angle: Displays a range of 0-100%. This parameter indicates the amount of throttle opening.
TR Sw.: Displays Park/Neutral, Reverse, Drive4, Drive3, Drive2, Drive1 or Invalid. This parameter is the decoded status of the four A/B/C/P inputs from the transmission range switch. Invalid is displayed when the PCM does not recognize a valid combination of inputs.
TR Sw. A/B/C/P: Displays HI/LOW, HI/LOW, HI/LOW, HI/LOW. This parameter indicates the status of the four inputs from the transmission range switch to the PCM. HI indicates an ignition voltage input to the PCM. LOW indicates a zero voltage input to the PCM.
Trans. Fluid Temp.: Displays a range of -40°C to 151°C (-40°F to 304°F). This parameter is the input signal of the transmission fluid temperature sensor. Transmission fluid temperature is high (151°C) when signal voltage is low (0 V), and transmission fluid temperature is low (-40°C) when signal voltage is high (5 V).
Transmission Hot Mode: Displays On or Off. This parameter monitors transmission temperature. On indicates that the transmission temperature has exceeded 135°C (275°F).
Transmission OSS (Output Speed Sensor): Displays a range of 0-8192 RPM. This parameter indicates the rotational speed of the transmission output shaft expressed as revolutions per minute.
Vehicle Speed: Displays a range of 0-255 km/h (0-158 mph). This parameter is the input signal from the vehicle speed sensor assembly.
1-2 Shift Time: Displays a range of 0.00-6.38 seconds. This parameter is the actual time of the last 1-2 shift. The shift time is based on the engine RPM drop after the commanded 1-2 shift. This value is only accurate if the shift was adaptable.
1-2 Sol.: Displays ON or OFF. This parameter is the commanded state of the 1-2 shift solenoid valve. ON represents a commanded energized state (current is flowing through the solenoid). OFF represents a non-commanded state (current is not flowing through the solenoid).
1-2 Sol. Open/Short to GND: Displays Yes or No. This parameter indicates if an open or short to ground exists in the 1-2 shift solenoid valve feedback signal to the PCM. This parameter is valid only when the 1-2 shift solenoid is commanded OFF.
1-2 Sol. Short to Volts: Displays Yes or No. This parameter indicates if a short to voltage exists in the 1-2 shift solenoid valve feedback signal to the PCM. This parameter is valid only when the 1-2 shift solenoid is commanded ON.
1-2 Tap Cell (4-16): Displays kPa or psi. This parameter displays the amount of pressure varied from a calibrated base line pressure for shifts. Each TAP Cell is based on a calibrated shift torque value. Each TAP Cell value is calculated from the last shift time. This cell pressure is used in addition to the calibrated base line pressure to adjust the apply of a clutch or band during the next shift.
2-3 Shift Error: Displays a range of -6.38 to +6.38 seconds. This parameter is the difference between the desired 2-3 shift time and the actual 2-3 shift time. A positive number indicates a firm or fast shift (the actual shift time was shorter than the desired shift time). A negative number indicates a soft or slow shift (the actual shift time was longer than the desired shift time). This value is only accurate if the shift was adaptable.
2-3 Shift Time: Displays a range of 0.00-6.38 seconds. This parameter is the actual time of the last 2-3 shift. The shift time is based on the engine RPM drop after the commanded 2-3 shift. This value is only accurate if the shift was adaptable.
2-3 Sol.: Displays ON or OFF. This parameter is the commanded state of the 2-3 shift solenoid valve. ON represents a commanded energized state (current is flowing through the solenoid). OFF represents a non-commanded state (current is not flowing through the solenoid).
2-3 Sol. Open/Short to GND: Displays Yes or No. This parameter indicates if an open or short to ground exists in the 2-3 shift solenoid valve feedback signal to the PCM. This parameter is valid only when the 2-3 shift solenoid is commanded OFF.
2-3 Sol. Short to Volts: Displays Yes or No. This parameter indicates if a short to voltage exists in the 2-3 shift solenoid valve feedback signal to the PCM. This parameter is valid only when the 2-3 shift solenoid is commanded ON.
2-3 Tap Cell (4-16): See 1-2 Tap Cell (4-16)
3-2 Downshift Sol.: Displays On or Off. This parameter indicates if the 3-2 shift solenoid valve assembly is currently commanded On or Off. The solenoid commanded state is based on the transmission temperature and the commanded gear. The solenoid will change states during a 3-2 downshift to regulate the appropriate pressure.
3-2 Sol. Open/Short to GND: Displays Yes or No. This parameter indicates if an open or short to ground exists in the 3-2 shift solenoid valve assembly feedback signal to the PCM. This parameter is valid only when the 3-2 shift solenoid is commanded OFF.
3-2 Sol. Short to Volts: Displays Yes or No. This parameter indicates if a short to voltage exists in the 3-2 shift solenoid valve assembly feedback signal to the PCM. This parameter is valid only when the 3-2 shift solenoid is commanded ON.
3-4 Shift Error: Displays a range of -6.38 to +6.38 seconds. This parameter is the difference between the desired 3-4 shift time and the actual 3-4 shift time. A positive number indicates a firm or fast shift (the actual shift time was shorter than the desired shift time). A negative number indicates a soft or slow shift (the actual shift time was longer than the desired shift time). This value is only accurate if the shift was adaptable.
3-4 Shift Time: Displays a range of 0.00-6.38 seconds. This parameter is the actual time of the last 3-4 shift. The shift time is based on the engine RPM drop after the commanded 3-4 shift. This value is only accurate if the shift was adaptable.
A/C Clutch: Displays On or Off. This parameter indicates the commanded state of the A/C control relay. The clutch should be engaged when On displays.
Cruise: Displays Enabled or Disabled. This parameter indicates whether the PCM is allowing cruise operation. The PCM has the ability to disable cruise control under certain conditions.
Current Gear: Displays 1, 2, 3 or 4. This parameter indicates the current commanded state of the shift solenoids.
Current TAP (Transmission Adaptive Pressure) Cell: The scan tool displays cells 4-16. This parameter indicates the current TAP cell in use for transmission line pressure adaptation. The cells are based on engine torque. The higher the engine torque, the higher the current TAP cell. The last cell used will remain displayed until the next adaptable upshift occurs.
ECT (Engine Coolant Temperature): Displays a range of -40°C to 151°C (-40°F to 304°F). This parameter is the input signal of the engine coolant temperature sensor. The engine coolant temperature is high (151°C) when the signal voltage is low (0 V), and the engine coolant temperature is low (-40°) when the signal voltage is high (5 V).
Engine Run Time: Displays a range of 0:00:00-18:12:15 hr/min/sec. This parameter measures how long the engine has been operating. When the ignition switch is turned OFF, the value is reset to zero.
Engine Speed: Displays a range of 0-8192 RPM. This parameter indicates the rotational speed of the engine expressed as revolutions per minute.
Engine Torque: Displays a range of 0-9999 lbs ft. This parameter indicates the amount of torque that is delivered from the engine.
Estimated Gear Ratio: Displays a range of 0.00:1-8.00:1. This parameter indicates the estimated turbine speed divided by the transmission output speed. Estimated turbine speed is calculated from engine speed and engine torque.
Ignition Voltage: Displays a range of 0.0-25.5 V. This represents the system voltage measured by the PCM at it's ignition feed.
Last Shift Time: Range 0.00-6.38 seconds. This parameter is the actual shift time of the last shift.
PC Sol. Actual Current: Displays a range of 0.00-1.10 amps. This parameter is the actual current of the pressure control solenoid circuit at the control module. Zero amp (no current flow) indicates actual higher line pressure. Actual lower line pressure is indicated by 1.1 amps (high current flow).
PC Sol. Duty Cycle: Displays a range of 0-100%. This parameter is the commanded state of the pressure control solenoid expressed as a percent of energized ON time. Zero percent indicates zero ON time (non-energized) or no current flow. Approximately 60% at idle indicates maximum ON time (energized) or high current flow.
PC Ref. (Reference) Current: Displays a range of 0.00-1.10 amps. This parameter is the commanded current of the pressure control solenoid circuit. Zero amp (no current flow) indicates commanded higher line pressure. Commanded lower line pressure is indicated by 1.1 amps (high current flow).
Speed Ratio: Displays a range of 0.00:1-8.00:1. This parameter indicates engine speed divided by transmission output speed. This value is used to estimate transmission gear ratio.
TCC Brake Switch: Displays Open or Closed. This parameter indicates the state of the brake switch circuit input. Open indicates a zero voltage input (brake switch open, brake pedal applied). Closed indicates a B+ voltage input (brake switch closed, brake pedal released).
TCC Duty Cycle: Displays a range of 0-100%. This parameter is the commanded percentage of ON time of the TCC PWM solenoid. Approximately 90% represents an ON (energized) commanded state. Zero percent represents an OFF (non-energized) commanded state. This commanded state is applied at a vehicle speed between approximately 0-16 km/h (0-10 mph).
TCC Duty Cycle Open/Short to GND: Displays Yes or No. This parameter indicates whether an open or a short to ground exists in the TCC PWM solenoid valve feedback signal to the PCM. This parameter is valid only when the TCC PWM solenoid is commanded OFF (duty cycle is 0%).
TCC Duty Cycle Short to Volts: Displays Yes or No. This parameter indicates whether a short to voltage exists in the TCC PWM solenoid valve feedback signal to the PCM. This parameter is valid only when the TCC PWM solenoid is commanded ON (duty cycle is at maximum).
TCC Enable: Displays Yes or No. This parameter is the commanded state of the TCC solenoid. Yes indicates a commanded energized state (current is flowing through the solenoid). No indicates a commanded non-energized state (current is not flowing through the solenoid). This commanded state occurs at various vehicle speeds between applications.
TCC Enable Open/Short to GND: Displays Yes or No. This parameter indicates whether an open or a short to ground exists in the TCC solenoid valve feedback signal to the PCM. This parameter is valid only when the TCC solenoid is commanded OFF.
TCC Enable Short to Volts: Displays Yes or No. This parameter indicates whether a short to voltage exists in the TCC solenoid valve feedback signal to the PCM. This parameter is valid only when the TCC solenoid is commanded ON.
TCC (Torque Converter Clutch) Slip Speed: Displays a range of -4080 to 4079 RPM. This parameter is the difference between transmission output speed and engine speed. A negative value indicates that the engine speed is less than the output speed (deceleration). A positive value indicates that the engine speed is greater than the output speed (acceleration). A value of zero indicates that the engine speed is equal to the output speed (TCC applied).
TFT (Transmission Fluid Temperature) Sensor: Displays a range of 0.00-5.00 V. When the transmission fluid is cold, the sensor resistance is high and the PCM will sense high signal voltage. As the transmission fluid temperature warms to a normal operating temperature, the sensor resistance becomes less and the voltage decreases.
TFP Sw.: Displays Park/Neutral, Reverse, Drive4, Drive3, Drive2, Drive1 or Invalid. This parameter is the decoded status of the three A/B/C inputs from the automatic transmission fluid pressure manual valve position switch. Invalid is displayed when the PCM does not recognize a valid combination of inputs.
TFP Sw. A/B/C: Displays HI/LOW, HI/LOW, HI/LOW. This parameter indicates the status of the three inputs from the Automatic Transmission Fluid Pressure Manual Valve Position Switch Assembly to the PCM. LOW represents a 0 voltage signal. HI represents an ignition voltage signal.
Torque Converter Efficiency - (Ratio): Displays a ratio of .00:1-2:1. The ratio is calculated by multiplying the speed ratio by a value related to the "K factor" of the torque converter. The "K factor" is the looseness or tightness of the torque converter for a given torque. The nearer the torque converter is to full coupling (i.e. 1:1) the closer the torque converter efficiency number will be to 1.
TP Indicated Angle: Displays a range of 0-100%. This parameter indicates the amount of throttle opening.
TR Sw.: Displays Park/Neutral, Reverse, Drive4, Drive3, Drive2, Drive1 or Invalid. This parameter is the decoded status of the four A/B/C/P inputs from the transmission range switch. Invalid is displayed when the PCM does not recognize a valid combination of inputs.
TR Sw. A/B/C/P: Displays HI/LOW, HI/LOW, HI/LOW, HI/LOW. This parameter indicates the status of the four inputs from the transmission range switch to the PCM. HI indicates an ignition voltage input to the PCM. LOW indicates a zero voltage input to the PCM.
Trans. Fluid Temp.: Displays a range of -40°C to 151°C (-40°F to 304°F). This parameter is the input signal of the transmission fluid temperature sensor. Transmission fluid temperature is high (151°C) when signal voltage is low (0 V), and transmission fluid temperature is low (-40°C) when signal voltage is high (5 V).
Transmission Hot Mode: Displays On or Off. This parameter monitors transmission temperature. On indicates that the transmission temperature has exceeded 135°C (275°F).
Transmission OSS (Output Speed Sensor): Displays a range of 0-8192 RPM. This parameter indicates the rotational speed of the transmission output shaft expressed as revolutions per minute.
Vehicle Speed: Displays a range of 0-255 km/h (0-158 mph). This parameter is the input signal from the vehicle speed sensor assembly.
