GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2001 🢒 Corvette 🢒 Steering 🢒 Steering Wheel and Column - Tilt 🢒 Inflatable Restraint Steering Wheel Module Coil Assemble - Off Vehicle

Inflatable Restraint Steering Wheel Module Coil Assemble - Off Vehicle Non-Telescoping Column


    Object Number: 293254 Size: SH
  1. Align the block tooth on the steering shaft assembly (1) to the 12 o'clock position.
  2. Place the ignition switch in the LOCK position.

    3. Object Number: 415291 Size: SH

    Important: A new inflatable restraint steering wheel module coil will be pre-centered. Do not remove the centering tab from the new inflatable restraint steering wheel module coil until the installation is complete.

  3. If installing the existing inflatable restraint steering wheel module coil, it must be centered first. Refer to Inflatable Restraint Coil Centering - Off Vehicle .
  4. Align the inflatable restraint steering wheel module coil (4) with the horn tower on the turn signal cancel cam assembly (1).
  5. Slide the inflatable restraint steering wheel module coil (4) onto the steering shaft assembly (2).
  6. Firmly seat the retaining ring (3) into the groove on the steering shaft assembly (2).
  7. Remove and discard the centering tab from the new inflatable restraint steering wheel module coil (4).

    8. Object Number: 415293 Size: SH

    Caution: Improper routing of the wire harness assembly may damage the inflatable restraint steering wheel module coil. This may result in a malfunction of the coil, which may cause personal injury.

  8. Reconnect the inflatable restraint steering wheel module coil connector.
  9. Attach new wire harness strap (2) to the wire harness assembly (1) and the steering column.
  10. Install the upper and lower trim covers. Refer to Steering Column Trim Covers - Assemble - Off Vehicle .
  11. Enable the inflatable restraint steering wheel module. Refer to Enabling the SIR System in SIR.

Inflatable Restraint Steering Wheel Module Coil Assemble - Off Vehicle Telescoping Column


    Object Number: 293254 Size: SH
  1. Align the block tooth on the steering shaft assembly (1) to the 12 o'clock position.

    2. Object Number: 415291 Size: SH

    Important: A new inflatable restraint steering wheel module coil will be pre-centered. Do not remove the centering tab from the new inflatable restraint steering wheel module coil until the installation is complete.

  2. Align the inflatable restraint steering wheel module coil (4) with the horn tower on the turn signal cancel cam assembly (1).
  3. Firmly seat the retaining ring (3) into the groove on the steering shaft assembly (2).
  4. If installing the existing inflatable restraint steering wheel module coil it must be centered first. Refer to Inflatable Restraint Coil Centering - Off Vehicle .
  5. Slide the new inflatable restraint steering wheel module coil (4) onto the steering shaft assembly (2).
  6. Remove and discard the centering tab from the new inflatable restraint steering wheel module coil (4).

    7. Object Number: 415293 Size: SH

    Caution: Improper routing of the wire harness assembly may damage the inflatable restraint steering wheel module coil. This may result in a malfunction of the coil, which may cause personal injury.

  7. Reconnect the inflatable restraint steering wheel module coil connector.
  8. Attach new wire harness strap (2) to the wire harness assembly (1) and the steering column.
  9. Install the upper and lower trim covers. Refer to Steering Column Trim Covers - Assemble - Off Vehicle .
  10. Enable the inflatable restraint steering wheel module. Refer to Enabling the SIR System in SIR.