GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2006 🢒 Malibu 🢒 Body 🢒 Exterior Trim 🢒 Rear Compartment Lid Emblem/Nameplate Replacement

Rear Compartment Lid Emblem/Nameplate Replacement Sedan

Removal Procedure
  1. When replacing an emblem/nameplate, do the following:
    2. • Use tape to protect the mounting surface during removal.
    • Use tape for alignment marks for installation of the emblem/nameplate.
  2. To remove an emblem/nameplate, heat the emblem/nameplate using a heat gun.
  3. Apply the heat using a circular motion for about 30 seconds holding the heat gun approximately 152 mm (6 in) from the surface.

    4. Object Number: 321645 Size: SH

    Notice: Use a plastic, flat-bladed tool to prevent paint damage when removing an emblem/name plate.

  4. Use a plastic, flat-bladed tool to remove the emblem/nameplate from the panel surface.
  5. When replacing, remove all adhesive as follows:
    6. • For body panels, use a 3M™ Scotch Brite molding adhesive remover disk 3M™ P/N 07501 or equivalent.
    • For plastic panels, use a lint-free cloth and Varnish Makers and Painters (VMP) Naphtha or a 50/50 mixture, by volume of isopropyl alcohol and water to remove the adhesive.

Installation Procedure

    Important: Apply the emblem/nameplate in an environment that is free from dust or other dirt that could come into contact with the sticky backing. Foreign material may cause improper adhesion.

  1. Clean the area where the emblem/nameplate will be installed. Use a lint free cloth and VMP Naphtha or a 50/50 mixture, by volume of isopropyl alcohol and water to clean the area.

  2. Dry the area thoroughly.
  3. If the location of the emblem/nameplate has not been marked, apply tape and use the following dimensions:

    4. Object Number: 1326312 Size: MH
    • For the sedan emblem/nameplate, install to the following dimensions:
       • Dimension (a) is 76 mm (3.02 in) from the left edge of the rear compartment lid applique to the nameplate.
       • Dimension (b) is 97.6 mm (5.83 in) from the bottom feature line of the rear compartment lid applique to the nameplate.
    • For the coupe emblem/nameplate, install to the following dimensions:
       • Dimension (a) is 22 mm (0.88 in) from the top of the applique to the bottom of the nameplate.
       • Dimension (b) is 38 mm (1.5 in) from the edge of the rear compartment lid to the side of the nameplate.
       • Dimension (c) is 125 mm (5 in) from the edge of the deck lid to the edge of the nameplate.
  4. Use a heat gun to heat the mounting surface to approximately 27-41°C (80-105°F).
  5. Ensure that the temperature of the emblem/nameplate is approximately 29-32°C (85-90°F).

    6. Important: Do not touch the adhesive backing on the emblem/nameplate.

  6. Remove the protective liner from the back of the emblem/name plate.
  7. Position the emblem/nameplate to the location marks and press the emblem/nameplate to the mounting surface.
  8. Apply equal pressure along the emblem/nameplate to uniformly bond the item to the mounting surface.
  9. Remove the protective tape from the mounting surface.

Rear Compartment Lid Emblem/Nameplate Replacement SS Extended Sedan


Object Number: 1675045 Size: SF

Callout

Component Name

Fastener Tightening Specifications: Refer to Fastener Tightening Specifications.

1

Extended Sedan Rear Compartment Lid Plate Assembly (SS)

  1. When removing protective liners from adhesive backed emblems/nameplates, be careful not to touch the tape with hands and do not allow the tape to come in contact with dirt or any foreign matter prior to adhesion.
  2. Use a J 25070 or equivalent to remove the old emblem/nameplate. Clean all the adhesive residue from the rear compartment lid, wipe the surface dry with a clean lint-free towel prior to installing the new SS emblem/nameplate.
  3. Press the emblem firmly to the rear compartment lid to ensure full adhesion.