Seat Belt Retractor Replacement - Left Front VIN 5

1. Open the upper seat belt guide loop plastic cover (7).
2. Remove the upper seat belt guide loop nut (5).
3. Remove the upper guide loop (6) from the adjuster bracket (1).



4. Remove the rear carpet retainer. Refer to Carpet Retainer Replacement in Interior Trim.
5. Remove the lower the seat belt anchor plate bolt.
6. Remove the anchor plate from the center pillar.
7. Route the seat belt (4) from the hole at the bottom of the carpet retainer.
8. Remove the seat belt retractor bolt (2).
9. Remove the seat retractor side belt (1) from the vehicle.

1. Install the seat retractor side belt (1) to the vehicle.
2. Install the seat belt retractor into the T-slot in the center pillar.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

3. Install the seat belt retractor bolt (2).

Tighten
Tighten the seat belt retractor bolt to 42 N·m (31 lb ft).

4. Route the seat belt (4) through the hole at the bottom of the carpet retainer.
5. Position the anchor plate to the center pillar.
6. Install the lower seat belt anchor plate bolt.

Tighten
Tighten the lower seat belt anchor plate bolt to 42 N·m (31 lb ft).

7. Route the seat belt (4) through the slot in the rear carpet retainer.
8. Install the rear carpet retainer. Refer to Carpet Retainer Replacement in Interior Trim.



9. Install the upper guide loop (6) to the adjuster bracket (1).
10. Install the upper seat belt guide loop nut (5).

Tighten
Tighten the upper seat belt guide loop nut to 42 N·m (31 lb ft).

11. Close the upper seat belt guide loop plastic cover (7).

Seat Belt Retractor Replacement - Left Front VIN 1

1. Remove the rear seat cushion and the seat back.

•	Refer to Rear Seat Cushion Replacement in Seats.

•	Refer to Rear Seat Back Replacement in Seats.

2. Remove the rear window trim panel. Refer to Rear Window Shelf Trim Panel Replacement in Interior Trim.



3. Open the plastic cover (1) of the upper seat belt guide loop.
4. Remove the upper seat belt guide loop bolt (3).
5. Remove the upper seat belt guide loop (2) from the quarter upper trim panel (6).
6. Remove the coat hook.

Refer to Coat Hook Replacement in Interior Trim.

7. Remove the quarter upper trim finish panel.

Refer to Rear Quarter Upper Trim Panel Replacement in Interior Trim.

8. Remove the quarter lower trim finish panel.

Refer to Rear Quarter Lower Trim Panel Replacement in Interior Trim.




9. Remove the seat belt (2) from the seat belt guide (1) through the slit in the guide.



10. Slide the sleeve upward in order to expose the lower seat belt anchor plate bolt (2).
11. Remove the lower seat belt anchor plate bolt (2).
12. Remove the bushing (3) at the lower seat belt anchor.
13. Remove the seat belt (1) from the slot in the quarter lower trim finish panel (4).



14. Remove the seat belt retractor bolt (3).
15. Remove the driver seat retractor side belt (2) from the vehicle.

1. Install the driver seat retractor side belt (2) to the vehicle.
2. Install the belt retractor (5) into the T-slot in the lower quarter finish panel (4).

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

3. Install the seat belt retractor bolt (2).

Tighten
Tighten the seat belt retractor bolt to 42 N·m (31 lb ft).




4. Route the seat belt (1) through the slot in the quarter lower trim finish panel (4).
5. Install the bushing (3) at the lower seat belt anchor.
6. Install the lower seat belt anchor plate bolt.

Tighten
Tighten the lower seat belt anchor plate bolt to 42 N·m (31 lb ft).

7. Slide the sleeve downward in order to cover the seat belt anchor bolt.



8. Position the seat belt (2) into the guide (1) by placing the seat belt through the slit in the guide.
9. Install the quarter lower finish trim panel.

Refer to Rear Quarter Lower Trim Panel Replacement in Interior Trim.

10. Install the quarter upper finish trim panel.

Refer to Rear Quarter Upper Trim Panel Replacement in Interior Trim.

11. Install the coat hook.

Refer to Coat Hook Replacement in Interior Trim.




12. Install the upper seat belt guide loop (2) to the upper quarter trim panel (6).
13. Install the upper seat belt guide loop bolt (3).

Tighten
Tighten the upper seat belt guide loop bolt to 42 N·m (31 lb ft).

14. Close the upper seat belt guide loop plastic cover (1).
15. Install the rear window trim panel. Refer to Rear Window Shelf Trim Panel Replacement in Interior Trim.
16. Install the rear seat back and the cushion.

•	Refer to Rear Seat Cushion Replacement in Seats.

•	Refer to Rear Seat Back Replacement in Seats.