GM Service Manual Online
For 1990-2009 cars only

Object Number: 42275  Size: MF
Master Electrical Component List
Automatic Transmission Controls Schematics 4.3L
Automatic Transmission Controls Schematics 4.8, 5.3, 6.0L
OBD II Symbol Description Notice

Circuit Description

The torque converter clutch (TCC) solenoid valve is a normally-open exhaust valve that is used with the torque converter clutch pulse width modulation (TCC PWM) solenoid valve in order to control fluid acting on the converter clutch apply valve. The TCC solenoid valve attaches to the transmission case assembly extending into the pump cover. When grounded (energized) by the powertrain control module (PCM), the TCC solenoid valve stops converter signal oil from exhausting. This causes converter signal oil pressure to increase and move the converter clutch apply valve against spring force and into the apply position. In this position, release fluid is open to an exhaust port and converter feed fluid fills the apply fluid circuit. The converter feed fluid applies the TCC. When the PCM no longer provides a ground path, the TCC solenoid valve de-energizes and apply fluid exhausts, releasing the TCC.

When the PCM detects low TCC slip speed when the TCC is commanded OFF, then DTC P0742 sets. DTC P0742 is a type B DTC.

Conditions for Running the DTC

    â€¢ No TP sensor DTCs P0122 or P0123.
    â€¢ No VSS assembly DTCs P0502 or P0503.
    â€¢ No TCC solenoid valve DTC P0740.
    â€¢ No TFP manual valve position switch DTC P1810.
    â€¢ No TCC PWM solenoid valve DTC P1860.
    â€¢ The TP angle is 17-45 percent.
    â€¢ The engine speed is greater than 450 RPM for 6 seconds.
    â€¢ The engine is not in fuel cutoff.
    â€¢ The TFT is between 20-130°C (68-266°F).
    â€¢ The engine vacuum is 0-105 kPa (0-15 psi).
    â€¢ The engine torque is 67-542 N·m (50-400 lb ft).
    â€¢ The engine speed is 1000-3000 RPM.
    â€¢ The speed ratio is 0.64 to 1.35.
    â€¢ The vehicle speed is 24-80 km/h (15-50 mph).
    â€¢ The gear range does not change within 5 seconds.
    â€¢ The commanded gear is not 1st.
    â€¢ The gear range is D4.
    â€¢ The TCC is commanded OFF.

Conditions for Setting the DTC

DTC P0742 sets if the following condition occurs twice.

The TCC slip speed is -20 to +20 RPM  for 5 seconds.

Action Taken When the DTC Sets

    â€¢ The PCM illuminates the malfunction indicator lamp (MIL) during the second consecutive trip in which the Conditions for Setting the DTC are met.
    â€¢ The PCM inhibits the TCC.
    â€¢ The PCM inhibits 4th gear in Hot Mode.
    â€¢ The PCM freezes shift adapts from being updated.
    â€¢ The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze Frame and Failure Records.
    â€¢ The PCM stores DTC P0742 in PCM history during the second consecutive trip in which the Conditions for Setting the DTC are met.

Conditions for Clearing the MIL/DTC

    â€¢ The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.
    â€¢ A scan tool can clear the MIL/DTC.
    â€¢ The PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without an emission-related diagnostic fault occurring.
    â€¢ The PCM cancels the DTC default actions when the fault no longer exists and/or the ignition switch is OFF long enough in order to power down the PCM.

Diagnostic Aids

The TCC fluid hydraulically applies the TCC, possibly causing an engine stall, under the following conditions:

    â€¢ The TCC is hydraulically stuck ON
    â€¢ The parking brake is applied
    â€¢ Any gear range is selected

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. This step tests the hydraulic state of the TCC. When the PCM commands the TCC solenoid valve OFF, the slip speed should increase.

DTC P0742

Step

Action

Value(s)

Yes

No

1

Did you perform the Powertrain Diagnostic System Check?

--

Go to Step 2

Go to Diagnostic System Check - Engine Controls in Engine Controls - 4.3 L or Diagnostic System Check - Engine Controls in Engine Controls - 4.8 L, 5.3 L and 6.0 L

2

  1. Install a Scan Tool .
  2. Turn ON the ignition, with the engine OFF.
  3. Important: Before clearing the DTC, use the Scan Tool in order to record the Freeze Frame and Failure Records. Using the Clear Info function erases the Freeze Frame and Failure Records from the PCM.

  4. Record the DTC Freeze Frame and Failure Records.
  5. Clear the DTC.
  6. Drive the vehicle in the D4 drive range in second, third or fourth gear under steady acceleration, with a TP angle at 20%.

While the Scan Tool TCC Enable status is NO, does the Scan Tool display a TCC Slip Speed within the specified range?

-20 to +20 RPM

Go to Step 3

Go to Diagnostic Aids

3

The TCC is hydraulically stuck ON. Inspect for the following:

    â€¢ Clogged exhaust orifice in the TCC solenoid valve.
    â€¢ Converter clutch apply valve stuck in the apply position.
    â€¢ Misaligned or damaged valve body gasket.
    â€¢ Restricted release passage.
    â€¢ Restricted transmission cooler line.

Did you find and correct the condition?

--

Go to Step 4

--

4

Perform the following procedure in order to verify the repair:

  1. Select DTC.
  2. Select Clear Info.
  3. Drive the vehicle in D4 with the TCC OFF and the throttle above 17%. Ensure that the Scan Tool TCC Slip Speed is 100-2000 RPM for 5 seconds.
  4. Select Specific DTC.
  5. Enter DTC P0742.

Has the test run and passed?

--

System OK

Go to Step 1