HIGH EFFORT REQUIRED TO SOUND HORN(REPL. STEERING WHEEL. Chevrolet Venture 1997

SUBJECT: HIGH EFFORT REQUIRED TO SOUND HORN (REPLACE STEERING WHEEL INFLATABLE RESTRAINT MODULE ATTACHING PINS)

MODELS: 1997-98 CHEVROLET VENTURE

CONDITION:

SOME OWNERS MAY COMMENT THAT A HIGH AMOUNT OF EFFORT IS REQUIRED TO SOUND THE HORN.

CORRECTION:

INSTALL NEW INFLATABLE RESTRAINT MODULE ATTACHING PINS IN THE STEERING WHEEL, USING THE FOLLOWING SERVICE PROCEDURE.

PROCEDURE:

1. RECORD RADIO PRESETS. 2. DISCONNECT NEGATIVE BATTERY CABLE. 3. DISABLE SIR SYSTEM. SEE SECTION 9J OF THE APPROPRIATE SERVICE MANUAL. 4. TURN IGNITION SWITCH TO THE "ON" POSITION. 5. FOR ACCESS TO THE TWO INFLATABLE RESTRAINT MODULE ATTACHING SCREWS ON THE BACKSIDE OF THE STEERING WHEEL, TURN THE STEERING WHEEL 90 DEGREES (1/4 TURN) FROM THE CENTER (STRAIGHT AHEAD) POSITION. IN THIS POSITION, ONE SCREW IS ACCESSIBLE FROM THE TOP SIDE OF THE STEERING COLUMN AND THE OTHER SCREW IS ACCESSIBLE FROM THE BOTTOM SIDE OF THE COLUMN. USE THE TILT FEATURE ON THE STEERING COLUMN AS NECESSARY TO IMPROVE ACCESS. 6. TURN IGNITION SWITCH TO THE "OFF" POSITION. 7. USING A "T-30" TORX(R) HEAD TOOL, OR EQUIVALENT, COMPLETELY LOOSEN THE TWO SCREWS THAT ATTACH THE INFLATABLE RESTRAINT MODULE TO THE STEERING WHEEL. WHEN LOOSE, THE TWO SCREWS WILL REMAIN IN THE STEERING WHEEL AND IT IS NOT NECESSARY TO REMOVE THEM. 8. REMOVE THE INFLATABLE RESTRAINT MODULE FROM THE STEERING WHEEL AND DISCONNECT THE ELECTRICAL CONNECTION. 9. REMOVE THE TWO SPRING CLIPS THAT RETAIN THE PINS IN THE BACKSIDE OF THE INFLATABLE RESTRAINT MODULE. SEE FIGURE 1. 10. REMOVE THE TWO PINS FROM THE INFLATABLE RESTRAINT MODULE AND DISCARD THE PINS.

IMPORTANT:

WHEN INSTALLING THE NEW PINS IN THE NEXT STEP, PLEASE NOTE THAT THEY ARE TO BE INSTALLED IN THE STEERING WHEEL AND NOT THE INFLATABLE RESTRAINT MODULE. ALSO NOTE THAT THEY ARE INDEXED AND CAN ONLY BE INSTALLED IN ONE POSITION.

11. POSITION THE TWO NEW PINS IN THE STEERING WHEEL AND SECURE FROM THE BACKSIDE OF THE WHEEL WITH THE TWO PREVIOUSLY LOOSENED SCREWS. SEE FIGURE 1. TIGHTEN SCREWS TO 4 N.M (30 LB IN). 12. REINSTALL THE TWO SPRING CLIPS ON THE INFLATABLE RESTRAINT MODULE. 13. RECONNECT THE INFLATABLE RESTRAINT MODULE ELECTRICAL CONNECTOR. 14. POSITION THE INFLATABLE RESTRAINT MODULE TO THE STEERING WHEEL AND CAREFULLY PUSH ON EACH SIDE UNTIL BOTH PINS ENGAGE (CLICK) IN THE SPRING CLIPS. 15. RECONNECT NEGATIVE BATTERY CABLE. 16. ENABLE THE SIR SYSTEM. SEE SECTION 9J OF THE APPROPRIATE SERVICE MANUAL. 17. RESET CLOCK AND PROGRAM RADIO PRESETS.

PARTS INFORMATION:

QUANTITY PER PACKAGED P/N DESCRIPTION VEHICLE QUANTITY ========= ================= =========== ======== 16823971 PINS, LOCKING SIR 2 2 MODULE

PARTS ARE EXPECTED TO BE AVAILABLE FROM GMSPO, 3/2/98.

WARRANTY INFORMATION:

FOR VEHICLES REPAIRED UNDER WARRANTY, USE:

LABOR OPERATION LABOR OPERATION NUMBER DESCRIPTION TIME ================ ======================= ===============

C8834 PINS, STEERING WHEEL 0.4 HR (INCLUDES ENABLE INFLATOR MODULE LOCKING - AND DISABLE SIR REPLACE SYSTEM)

FIGURES: 01

ATTACHMENTS: 00

FIGURE 1 1. SPRING CLIPS 2. OLD PINS BEFORE REMOVAL FROM INFLATABLE RESTRAINT MODULE 3. NEW PINS AFTER BEING INSTALLED IN STEERING WHEEL

Object Number: 335918 Size: MF

GENERAL MOTORS BULLETINS ARE INTENDED FOR USE BY PROFESSIONAL TECHNICIANS, NOT A "DO-IT-YOURSELFER". THEY ARE WRITTEN TO INFORM THOSE TECHNICIANS OF CONDITIONS THAT MAY OCCUR ON SOME VEHICLES, OR TO PROVIDE INFORMATION THAT COULD ASSIST IN THE PROPER SERVICE OF A VEHICLE. PROPERLY TRAINED TECHNICIANS HAVE THE EQUIPMENT, TOOLS, SAFETY INSTRUCTIONS AND KNOW-HOW TO DO A JOB PROPERLY AND SAFELY. IF A CONDITION IS DESCRIBED, DO NOT ASSUME THAT THE BULLETIN APPLIES TO YOUR VEHICLE, OR THAT YOUR VEHICLE WILL HAVE THAT CONDITION. SEE A GENERAL MOTORS DEALER SERVICING YOUR BRAND OF GENERAL MOTORS VEHICLE FOR INFORMATION ON WHETHER YOUR VEHICLE MAY BENEFIT FROM THE INFORMATION.