Instrument Panel Inflatable Restraint Module Replacement Oldsmobile

Caution: When you are carrying an undeployed inflator module:

1. Disable the SIR system. Refer to Disabling the SIR System .



2. Remove the IP carrier. Refer to Instrument Panel Upper Trim Pad Replacement in Instrument Panel, Gauges, and Console.
3. Remove the inflatable restraint IP module rear mounting fasteners (3).



4. Remove the foam insulator bracket (2).



5. Remove the foam insulator (2).



6. Remove the forward inflatable restraint IP module fasteners.
7. Remove the inflatable restraint IP module (1).
8. Fully deploy the module before disposal. If the module was replaced under warranty, fully deploy and dispose of the module after the required retention period. Refer to Inflator Module Handling, Shipping, and Scrapping .

1. Install the inflatable restraint IP module (1).
2. Install the forward inflatable restraint IP module mounting fasteners. Do not tighten the fasteners.



3. Install the foam insulator (2).



4. Install the foam insulator bracket (2).

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

5. Install the rear inflatable restraint IP module fasteners (3).

Tighten

•	Tighten the forward fasteners to 24 N·m (18 lb ft).

•	Tighten the rear fasteners to 11 N·m (94 lb in).

6. Install the IP carrier. Refer to Instrument Panel Upper Trim Pad Replacement in Instrument Panel, Gauges, and Console.
7. Enable the SIR system. Refer to Enabling the SIR System .

Instrument Panel Inflatable Restraint Module Replacement Buick

Caution: When you are carrying an undeployed inflator module:

1. Disable the SIR system. Refer to Disabling the SIR System .
2. Remove the Upper IP trim panel. Refer to Instrument Panel Upper Trim Pad Replacement in Instrument Panel, Gauges, and Console.
3. Remove the IP storage compartment. Refer to Instrument Panel Storage Compartment Replacement in Instrument Panel, Gauges, and Console.



4. Remove 5 fasteners (1) from the IP carrier.



5. Use a spacer in order to hold the right side of the IP carrier (1) out about 3.8 cm (1.5 in).



6. Remove the 2 inflatable restraint IP module upper fasteners (1).



7. Remove the 2 inflatable restraint IP module lower fasteners (1).



8. Remove the inflatable restraint module (1).
9. Fully deploy the module before disposal. If the module was replaced under warranty, fully deploy and dispose of the module after the required retention period. Refer to Inflator Module Handling, Shipping, and Scrapping .

1. Use a spacer in order to hold the right side of the IP carrier (1) out about 3.8 cm (1.5 in).



2. Install the inflatable restraint IP module (1).




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

3. Install the lower inflatable restraint IP module fasteners.

Tighten
Tighten the lower fasteners to 11 N·m (94 lb in).

Install the 2 inflatable restraint IP module lower fasteners (1).




4. Install the 2 inflatable restraint IP module upper fasteners (1).

Tighten
Tighten the upper fasteners to 24 N·m (18 lb ft).




5. Install 5 fasteners (1) to the IP carrier.



6. Install the IP storage compartment. Refer to Instrument Panel Storage Compartment Replacement in Instrument Panel, Gauges, and Console.
7. Install the Upper IP trim panel. Refer to Instrument Panel Upper Trim Pad Replacement in Instrument Panel, Gauges, and Console.
8. Enable the SIR system. Refer to Enabling the SIR System .