The Engine Scan Tool Data Definitions contains a brief description of all engine related parameters available on the scan tool. The list is in alphabetical order. A given parameter may appear in any one of the data lists. In some cases, the parameter may appear more than once or in more than one data list in order to group certain related parameters together.

12 Volt Reference: The scan tool displays OK or Fault. This parameter indicates the state of the IGN 1 input to the powertrain control module (PCM).

24X Crank Sensor : The scan tool displays RPM. This parameter displays engine speed based on the correlation of crankcase position (CKP) sensor A and B signals.

5 Volt Reference 1: The scan tool displays OK or Fault. This parameter indicates the state of the 5 volt reference A circuit. This circuit supplies the reference voltage to the throttle position (TP) sensor , manifold absolute pressure (MAP) sensor , and exhaust gas recirculation (EGR) pintle position sensor .

5 Volt Reference 2: The scan tool display OK or Fault. This parameter indicates the state of the 5 volt reference B circuit. This circuit supplies the reference voltage to the A/C pressure sensor , and the fuel tank pressure sensor .

A/C High Side Pressure: The scan tool range is 0.00-5.00 volts. This parameter indicates the A/C high side pressure sensor input to the PCM.

A/C Relay Command: The scan tool displays ON or OFF. This parameter indicates the PCM commanded state of the A/C relay control circuit.

Air Fuel Ratio: The scan tool displays the PCM commanded air to fuel. Air fuel ratio should normally be around 14.2:1-14.7:1. A lower air fuel ratio indicates a richer air to fuel mixture. A higher air fuel ratio indicates a leaner commanded air to fuel mixture.

AIR Pump Relay Command: The scan tool displays ON or OFF. This parameter indicates the PCM commanded state of the secondary air injection (AIR) pump relays.

AIR Solenoid Command: The scan tool displays ON or OFF. This parameter indicates the PCM commanded state of the AIR vacuum solenoid.

BARO: The scan tool range is 10-105 kPa. The barometric pressure (BARO) reading is determined from the MAP sensor signal. The PCM monitors the MAP signal during key up and wide-open throttle (WOT) conditions. The barometric pressure compensates for altitude differences.

CKP Sensor Status: The scan tool displays Angle, Time A, or Time B. This parameter indicates the engine position sensing mode. With both CKP sensors A and B working properly, this parameter should display Angle. If the PCM detects an incorrect condition with CKP sensor A, the PCM will command TIME B mode. If the PCM detects an incorrect condition with CKP sensor B, the PCM will command Time A mode.

CMP Sensor: The scan tool displays 0-16384 RPM. This parameter indicates engine speed as calculated from the camshaft position (CMP) sensor signal.

CMP Sensor Signal Present: The scan tool displays Yes/No.

Crank Request Signal: The scan tool displays Yes or No. Yes is displayed when the key is in the Crank position.

Cruise Inhibited Signal Command: The scan tool displays On or Off. On displayed indicates that the PCM is commanding the SMCC module to inhibit cruise control operation.

Cruise Control Active: The scan tool displays Yes or No.

Current Gear: The scan tool displays the numbers 1, 2, 3, or 4. The PCM looks at trans range position and the gear commanded by the PCM. The actual forward gear that the transaxle is in will be the lower of the two because the manual valve can override the PCM commanded gear. The scan tool displays which gear the transmission is in.

Cycles of Misfire Data: The scan tool range is 0-100. The parameter indicates which engine cycle of the 100 engine cycle test the PCM is collecting misfire data.

Desired EGR Position: The scan tool range is 0-100 percent . The parameter indicates the PCM commanded EGR pintle position. The desired EGR position should stay close to actual EGR position.

Desired Idle Speed: The scan tool range is 0-3187 RPM. The PCM commands the desired idle speed. The PCM compensates for various engine loads based on engine coolant temperature in order to keep the engine at the desired speed.

ECT Sensor: The scan tool range is -40°C to +150°C (-40°F to +302°F). This parameter indicates the engine coolant temperature based on input from the engine coolant temperature sensor .

EGR Position Sensor: The scan tool range is 0-100 percent/0-5 volts. Represents the actual position of the EGR pintle in percent. Zero percent displayed indicates a fully extended pintle (EGR valve closed).

Engine Load: The scan tool range is 0-100 percent . This parameter indicates the calculated engine load based on engine speed, and mass air flow (MAF) sensor readings. The engine load increases with an increase in RPM or airflow.

Engine Oil Level Switch: The scan tool displays OK or Low. The parameter displays Low if the engine oil level remains low (about 1 quart or more) for a sufficient period of time.

Engine Oil Pressure Switch: The scan tool displays OK or Low. This parameter displays whether or not sufficient engine oil pressure is present.

Engine Run Time: The scan tool displays Hours, Minutes, Seconds. This indicates the amount of engine run time. When the ignition is cycled OFF, the timer will reset to zero.

Engine Speed: The scan tool range is 0-16384 RPM. This parameter indicates the engine speed calculated by the PCM. The engine speed should remain close to desired idle under various engine loads with the engine idling.

EVAP Purge Solenoid Command: The scan tool range is 0-100 percent . This parameter indicates the PCM commanded duty cycle of the evaporative emission (EVAP) purge valve. A display of 0 percent indicates no purge while a display of 100 percent indicates full purge.

EVAP Test Abort Reason: The scan tool displays Not Aborted, Lost Enable, Small Leak, Veh. Not at Rest. This parameter indicates the reason the EVAP system test was aborted.

EVAP Test Result: The scan tool displays No Result, Aborted, Passed, Failed-DTC P0440, Failed-DTC P0442, Failed-DTC P0446, Failed-DTC P1441. This parameter indicates the results of the EVAP system tests.

EVAP Test State: The scan tool displays Wait For Purge, Test Running, Test Complete. This parameter indicates the state of the EVAP Service Bay Test.

EVAP Vent Solenoid Command: The scan tool displays Venting / Not Venting. This parameter indicates the PCM commanded state of the EVAP vent solenoid.

Extended Travel Brake Pedal Switch: The scan tool displays Applied, or Released. This parameter indicates the extended travel brake switch input to the PCM.

FC Relay 1 Command: The scan tool displays ON, or OFF. This parameter indicates the PCM commanded state of the low speed cooling fans.

FC Relay 2 and 3 Command: The scan tool displays ON, or OFF. This parameter indicates the PCM commanded state of the series parallel, and the cool fan 1 relays.

Fuel Level: The scan tool displays Liters, Gallons. This parameter displays the volume of fuel in the tank based on input from the fuel level sensor .

Fuel Level Sensor: The scan tool displays 0-5 volts. This parameter displays the fuel level input to the PCM.

Fuel Pump Relay Command: The scan tool displays ON or OFF. This parameter indicates the PCM commanded state of the fuel pump relay control circuit.

Fuel Tank Pressure Sensor: The scan tool range -17.5 to + 7.5 inches H2O (-33 to +14 mmHg) / 0 to 5 volts. This parameter indicates the fuel tank pressure sensor input to the PCM. The PCM uses the signal to determine the fuel tank pressure. The PCM uses the fuel tank pressure sensor input to determine the status of the EVAP system diagnostics.

Fuel Trim Cell: This parameter indicates the current fuel trim cell.

Generator L Terminal Signal Command: The scan tool displays ON / OFF. This parameter indicates the PCM commanded state of the generator L terminal. The PCM uses the L terminal to command the generator voltage regulator ON and OFF.

Generator F Terminal Signal: The scan tool displays 0-100 percent . This parameter indicates the generator field duty cycle as commanded by the voltage regulator. The PCM monitors the duty cycle using the generator F terminal circuit.

HO2S Bank 1 Sensor 1: The scan tool range is 0-1275 mV (0-1.275 volts). This parameter indicates the output voltage for heated oxygen sensor (HO2S) bank 1 sensor 1 (rear bank fuel control oxygen sensor). The voltage should fluctuate constantly within a range between about 50 mV (lean exhaust) and 800 mV (rich exhaust) while operating in Closed Loop.

HO2S Bank 1 Sensor 2: The scan tool range is 0-1275 mV (0-1.275 volts). This parameter indicates the output voltage for HO2S bank 1 sensor 2 (post catalyst oxygen sensor). The voltage should fluctuate within a range between about 50 mV (lean exhaust) and 800 mV (rich exhaust) while operating in Closed Loop. The post-catalyst HO2S output voltage will fluctuate slowly over a longer period of time, compared to the fuel control oxygen sensors. This is due to the oxygen storage capacity of an efficiently operating catalyst.

HO2S Bank 2 Sensor 1: The scan tool range is 0-1275 mV (0-1.275 volts). This parameter indicates the output voltage for HO2S bank 2 sensor 1 (front bank fuel control oxygen sensor). The voltage should fluctuate constantly within a range between about 50 mV (lean exhaust) and 800 mV (rich exhaust) while operating in Closed Loop.

HO2S Warm-up Bank 1 Sensor 2: The scan tool displays Seconds. This parameter indicates the time to warm-up for HO2S bank 1 sensor 2.

IAC Position: The scan tool range is 0-255 counts. This parameter displays the PCM commanded position of the idle air control pintle in counts. A larger number of counts indicates a retracted intake air control (IAC) valve which allows more air the idle air passage. The IAC position should respond quickly to changes in engine load in order to maintain the desired idle RPM.

IAT Sensor: The scan tool range is -40°C to +150°C (-40°F to +302°F). This parameter indicates the temperature of the intake air based on the signal voltage from the intake air temperature sensor .

Ignition 1 Signal: The scan tool range is 0-25.5 volts. This parameter indicates the system voltage detected by the PCM.

IMS: The scan tool displays Park, Park/Reverse, Reverse, Reverse/Neutral, Neutral, Neutral/Drive 4, Drive 4/Drive 3, Drive 3/Drive 2, Drive 2/Drive 1, Drive 1 or Invalid. This parameter is the decoded status of the four A/B/C/P inputs from the automatic transmission internal mode switch. If a valid combination of inputs is not received by the PCM, Invalid will be displayed.

Injector PWM Bank 1 / Bank 2: The scan tool range 0-985 milliseconds. This parameter indicates the PCM commanded pulse width for the bank 1 and bank 2 injectors.

Injector PWM Bank 1 AVG/ Bank 2 AVG: This parameter indicates the average pulse width of the bank 1 and bank 2 injectors.

Knock Retard: The scan tool range 0-45 degrees. This parameter indicates the amount of timing retard commanded by the PCM.

Long Term FT Avg. Bn1: The scan tool range is -99 to +99 percent . This parameter indicates the average Long Term FT correction for bank 1 calculated by the PCM during the current ignition cycle.

Long Term FT Avg Bn 2: The scan tool range is -99 to +99 percent . This parameter indicates the average Long Term FT correction for bank 2 calculated by the PCM during the current ignition cycle.

Long Term FT Bank 1: The scan tool range is -99 to +99 percent . This parameter indicates the Long Term FT correction for bank 1 as commanded by the PCM.

Long Term FT Bank 2: The scan tool range is -99 to +99 percent . This parameter indicates the Long Term FT correction for bank 2 as commanded by the PCM.

Loop Status: The scan tool displays Open, or Closed. This parameter indicates the state of the fuel control system. A CLOSED display indicates that the PCM is using the signals from the heated oxygen sensors to control the fuel system.

MAF Sensor: The scan tool range is 0-655 grams per second (g/s). This parameter indicates the volume of air entering the engine.

MAF Sensor: The scan tool range is 0-65535 Hz. This parameter indicates the MAF sensor frequency based on the volume of air entering the engine. The PCM converts the signal frequency to grams per second (g/s).

MAP Sensor: The scan tool range is 10-105 kPa/0-5 volts. This parameter indicates the manifold absolute pressure sensor input to the PCM.

MIL Command: The scan tool displays ON, or OFF. This parameter indicates the PCM commanded state of the malfunction indicator lamp (MIL).

Mileage Since DTC Cleared: The scan tool range is 0-1677722. This parameter indicates the actual vehicle miles stored in the PCM since the diagnostic trouble code (DTC)s were cleared.

Misfire Current #1 through #8: The scan tool range is 0-255 counts. This parameter indicates the possible misfires being detected on each cylinder during the last 2000 cylinder firing events. The counters may normally display some activity, but the activity should be very low and equal for all cylinders.

Misfire History #1 through #8: The scan tool range is 0-255 counts. This parameter indicates the total level of misfire that has been detected on each cylinder. The misfire history counters will not update or show any activity until a misfire or DTC P0300 has become active. The misfire history counter will update every 200 cylinder firing events.

Non-Driven Wheel Speed: The scan tool range is 0-255 km/h (0-158 mph). This parameter indicates the speed of the rear wheels. The PCM receives the information from the electronic brake and traction control module (EBCM) via class 2 serial data.

Odometer: The scan tool range is 0-1677722. This parameter indicates the actual vehicle miles stored in the PCM.

Powertrain Induced Chassis Pitch Command: The scan tool displays Active or Inactive.

Short Term FT Bank 1: The scan tool range is -99 to +99 percent . This parameter indicates the Short Term FT correction for bank 1 as commanded by the PCM.

Short Term FT Bank 2: The scan tool range is -99 to +99 percent . This parameter indicates the Short Term FT correction for bank 2 as commanded by the PCM.

Short Term FT Avg Bn 1: The scan tool range is -99 to +99 percent . This parameter indicates the average Short Term FT correction for bank 1 calculated by the PCM during the current ignition cycle.

Short Term FT Avg Bn 2: The scan tool range is -99 to +99 percent . This parameter indicates the average Short Term FT correction for bank 2 calculated by the PCM during the current ignition cycle.

Spark: The scan tool range is 0-64 degrees. This parameter indicates the amount of spark advance commanded by the PCM.

Start-up ECT: The scan tool range is -40°C to +150°C (-40°F to +302°F). This parameter indicates the engine coolant temperature at start-up.

Start-up IAT: The scan tool range is -40°C to +150°C (-40°F to +302°F). This parameter indicates the ambient air temperature at start-up.

Starter Relay Command: The scan tool displays ON, or OFF. This parameter indicates the PCM commanded state of the starter relay control circuit.

TCC Brake Pedal Switch: The scan tool displays Applied, or Released. This parameter indicates the torque converter clutch brake switch input to the PCM.

TCC Duty Cycle: The scan tool range is 0-100 percent. This display indicates the commanded percent of torque converter clutch (TCC) pulse width modulation (PWM) solenoid ON time. A display of 90 percent represents a fully energized commanded state. A display of 0 percent represents a de-energized commanded state.

TCC Enable Solenoid Command: The scan tool displays On / Off. This display indicates the commanded state of the torque converter clutch (TCC) solenoid.

TFP Sw.: The scan tool displays Park/Neutral, Reverse, Drive, or Invalid. This display indicates the decoded status of the two A/B inputs from the automatic transmission fluid pressure manual valve position switch.

TP Sensor: The scan tool range is 0-100 percent . This parameter indicates the throttle angle calculated by the PCM from the TP sensor voltage input.

TP Sensor : The scan tool range is 0-5 volts. This parameter indicates the TP sensor voltage input to the PCM.

Torque Delivered Signal: The scan tool displays 0-100 percent . This display indicates the amount of available engine torque.

Torque Request Signal: The scan tool displays 0-100 percent . This parameter indicates the amount of torque requested by the EBCM.

Traction Control Status: The scan tool display Active / Inactive. This parameter indicates the status of the traction control system.

Trans. Fluid Temp.: The scan tool range is -40°C to +150°C (-40°F to +302°F). This display indicates the temperature of the transmission fluid.

Vehicle Speed Sensor: The scan tool range is 0-255 km/h (0-158 mph). This parameter indicates the vehicle speed calculated by the PCM from the vehicle speed sensor .

VTD Auto Learn Timer: The scan tool indicates ACTIVE or INACTIVE. This parameter indicates the status of the vehicle theft deterrent system password learn.

VTD Fuel Disable: The scan tool displays Active, or Inactive. This parameter indicates the status of the theft deterrent fuel disable command.

VTD Password: The scan tool displays OK, or Incorrect. This parameter indicates the validity of the vehicle theft deterrent password.

Warm-ups w/o Emission Faults: The scan tool displays counts. This display indicates the number of warm-up cycles without an emission failure.

Warm-ups w/o Non-Emission Faults: The scan tool displays counts. This display indicates the number of warm-up cycles without a non-emission failure.