Caution: This vehicle is equipped with a Supplemental Inflatable Restraint (SIR) System. Failure to follow the correct procedure could cause the following conditions:

1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
2. Disable the SIR. Refer to Disabling the SIR System in SIR.
3. Apply the parking brake.
4. Remove the IP cluster trim plate bezel. Refer to Instrument Panel Cluster Trim Plate Bezel Replacement .
5. Remove the radio. Refer to Radio Replacement in Entertainment.
6. Remove the HVAC control module assembly. Refer to HVAC Control Module Replacement in HVAC Systems Automatic.
7. Insert the ignition key and turn the ignition switch to RUN, continue to step 8.

If the keys are unavailable or the ignition lock cylinder is seized proceed with the following:





7.1.	Remove the fasteners securing the ignition switch to the IP retainer.

7.2.	Push and release the retaining tab at the rear of the ignition switch.

7.3.	Remove the ignition switch through the radio opening in the retainer.

7.4.	Protect the immediate work area with suitable material such as clean shop towels or a clean fender cover.

7.5.	Locate the surface for the ignition switch lock cylinder release button (2) on the plastic ignition switch housing and center punch a location (1) on the "rib" approximately 3/8 inch rearward, toward the key entry end of the cylinder release button.

7.6.	Drill a pilot hole through the plastic housing with a 1/8 inch drill bit.

7.7.	Drill a larger hole at the pilot location, and slightly into the ignition switch lock cylinder surface to break the release button retaining spring using a 1/4 inch drill bit.

7.8.	Use a magnet and remove the retainer tab (2).

7.9.	Grasp the ignition switch lock cylinder and remove it from the switch housing.

7.10.

Remove any plastic "flash" from the drilling operation, and using compressed air blow out the ignition switch assembly, proceed to step 11.




8. Look through the radio opening in the IP retainer and locate the release button (1) on the side of the ignition switch.
9. Depress and hold the ignition lock cylinder retaining tab, located on the right lower side of the ignition switch, using a flat-bladed tool or other suitable tool.



10. Pull outward on the ignition cylinder (1) in order to remove the cylinder from the ignition switch.
11. Remove the reader/exciter module from the ignition lock cylinder. Refer to Theft Deterrent Exciter Module Replacement in Theft Deterrent.

1. Install the reader/exciter module to the ignition lock cylinder. Refer to Theft Deterrent Exciter Module Replacement in Theft Deterrent.
2. If ignition lock cylinder was previously seized proceed with steps 2.1 through 2.4, If not go to step 3.

2.1.	Turn the new ignition lock cylinder to the run position.

2.2.	Turn the ignition switch to the run position.

2.3.	Slowly push the ignition lock cylinder into the ignition switch until fully seated.

It may be necessary to slightly depress the release button as it passes by the 1/4 inch hole previously drill in the ignition switch housing.

2.4.	Reinstall the ignition switch. Refer to Ignition and Start Switch Replacement .

2.5.	Go to step 5.




3. Position the ignition lock cylinder (1) with the key installed into the opening in the ignition switch (2).
4. Press the ignition lock cylinder into place.

The lock cylinder retaining tab will produce an audible click when fully seated.

5. Using light force, pull on the lock cylinder in order to ensure the lock cylinder is engaged and secured in place.
6. Install the HVAC control module assembly. Refer to HVAC Control Module Replacement in HVAC Systems Automatic.
7. Install the radio. Refer to Radio Replacement in Entertainment.
8. Install the IP cluster trim plate bezel. Refer to Instrument Panel Cluster Trim Plate Bezel Replacement .
9. Install the IP center trim plate. Refer to Instrument Panel Center Trim Panel Replacement .
10. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
11. Inspect the ignition switch for proper operation in all positions.
12. Release the parking brake.
13. Enable the SIR system. Refer to Enabling the SIR System in SIR.