Exhaust Manifold Replacement Left Side

1. Remove the air cleaner duct. Refer to Engine Controls.
2. Remove the exhaust crossover. Refer to Exhaust Crossover Replacement .
3. Remove the electric engine cooling fans. Refer to Cooling and Radiator.



4. Remove the exhaust manifold retaining nuts.
5. Remove the exhaust manifold and heat shield.
6. Remove the exhaust manifold gasket.
7. If the exhaust manifold is being replaced, transfer the following parts:

•	The secondary air injection pipe

•	The heat shield

1. Install the exhaust manifold gasket.
2. Install the exhaust manifold and heat shield.
3. Install the exhaust manifold nuts.

Tighten
Tighten the nuts to 13 N·m (115 lb in).

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

4. Install the electric engine cooling fans. Refer to Cooling and Radiator.
5. Install the exhaust crossover. Refer to Exhaust Crossover Replacement .
6. Install the air cleaner duct. Refer to Engine Controls.

Exhaust Manifold Replacement Right Side

1. Remove the air cleaner duct. Refer to Engine Controls.
2. Remove the exhaust crossover pipe. Refer to Exhaust Crossover Replacement .
3. Disconnect the EGR tube from the exhaust manifold. Refer to Engine Controls.
4. Raise and suitably support the vehicle. Refer to General Information.
5. Remove the front exhaust pipe and the converter assembly. Refer to Exhaust System.
6. Remove the oxygen sensor. Refer to Engine Controls.
7. Remove the exhaust pipe front heat shield. Refer to Exhaust System.
8. Remove the rear generator brace. Refer to Engine Electrical.
9. Remove the transmission dipstick tube. Refer to Automatic Transaxle.
10. Remove the intermediate shaft from the steering gear. Refer to Power Steering Gear and Pump.
11. Remove the exhaust manifold nuts.
12. Install the jacking fixture in order to support the rear of the frame.
13. Remove the rear frame bolts.
14. Lower the frame.
15. Remove the steering gear heat shield. Refer to Power Steering Gear and Pump.
16. Remove the exhaust manifold heat shield.
17. Remove the exhaust manifold.



18. Remove the exhaust manifold gasket.
19. Clean the gasket mating surfaces.
20. If the exhaust manifold is being replaced, transfer the following parts:

•

The studs

•	The heat shield

1. Install the exhaust manifold gasket.
2. Install the exhaust manifold.
3. Install the exhaust manifold heat shield.
4. Install the exhaust manifold nuts.

Tighten
Tighten the nuts to 13 N·m (115 lb in).

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

5. Install the steering gear heat shield. Refer to Power Steering Gear and Pump.
6. Raise the frame.
7. Install the rear frame bolts. Refer to Body Dimensions and Underbody.
8. Remove the jacking fixture.
9. Connect the intermediate shaft to the steering gear. Refer to Power Steering Gear and Pump.
10. Install the transmission dipstick tube. Refer to Automatic Transaxle.
11. Install the rear generator brace. Refer to Engine Electrical.
12. Install the exhaust pipe front heat shield. Refer to Exhaust System.
13. Install the oxygen sensor. Refer to Engine Controls.
14. Install the front exhaust pipe and the converter assembly. Refer to Exhaust System.
15. Lower the vehicle.
16. Connect the EGR tube to the exhaust manifold. Refer to Engine Controls.
17. Install the exhaust crossover pipe. Refer to Exhaust Crossover Replacement .
18. Install the air cleaner duct. Refer to Engine Controls.