Front Seat Adjuster Replacement Six-Way Power

1. Remove the front seat. Refer to Bucket Seat Replacement .
2. Place the front seat upside down on a clean, protected surface.
3. Note the location of the power seat adjuster electrical wiring harness.



4. Disconnect and remove the electrical wiring harness from the adjuster assembly.
5. Remove the seat trim panel. Refer to Seat Cushion Outer Trim Panel Replacement .



6. Remove the seat adjuster to cushion frame bolts.
7. Remove the seat adjuster from the seat cushion frame.
8. Remove the drive cables. Refer to Seat Horizontal and Vertical Drive Cable Replacement .
9. Remove the cross-brace bolts.
10. Remove the cross-brace and separate the adjusters.

Important: Make sure both power seat adjusters are in phase with each other before attaching the cross-brace.

1. Attach the cross-brace to the power seat adjusters.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the cross-brace bolts.

Tighten
Tighten the cross-brace bolts to 6 N·m (53 lb in).

3. Install the drive cables. Refer to Seat Horizontal and Vertical Drive Cable Replacement .
4. Install the seat adjuster to the seat cushion frame.
5. Install the seat adjuster to the cushion frame bolts.

Tighten
Tighten the seat adjuster to cushion frame bolts to 24 N·m (18 lb ft).

6. Install the trim finish panels. Refer to Seat Cushion Outer Trim Panel Replacement .



7. Install and connect the electrical wiring harness to the adjuster assembly.
8. Install the front seat. Refer to Bucket Seat Replacement .

Front Seat Adjuster Replacement Two-Way Manual

1. Remove the front seat. Refer to Bucket Seat Replacement .
2. Place the seat upside down on a clean, protected surface.
3. Remove the trim finish panels. Refer to Seat Cushion Outer Trim Panel Replacement .
4. Remove the seat adjuster to seat cushion frame bolts.
5. Remove the seat adjuster from the seat cushion frame.



6. Remove the cross-wire and assist springs from the seat adjuster.
7. Remove the cross-brace bolts.
8. Separate the left and right seat adjusters.

Important: Before assembling the seat adjusters, make sure the tab bending downward at the center of the cross-brace faces towards the rear of the adjusters.

1. Attach the cross-brace to the seat adjusters.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the cross-brace bolts.

Tighten
Tighten the cross-brace bolts to 6 N·m (18 lb ft).

3. Install the cross-wire and assist springs to the seat adjuster.

Important: To ensure proper two-way seat adjuster alignment, install the adjuster assembly to the floor pan before attaching the adjuster to the seat cushion frame. The floor pan will act as an alignment fixture.

4. Install the seat adjuster to the floor pan.
5. Install the seat adjuster to floor pan bolts.

Tighten
Tighten the seat adjuster bolts to 42 N·m (31 lb ft).

6. Install the seat assembly to the seat adjuster.
7. Install the seat adjuster to cushion frame bolts.

Tighten
Tighten the seat adjuster to cushion frame bolts to 24 N·m (18 lb ft).

8. Install the trim finish panels. Refer to Seat Cushion Outer Trim Panel Replacement .
9. Install the front seat. Refer to Bucket Seat Replacement .
10. Connect any electrical connectors, if removed.