The radio has the THEFTLOCK™ feature if the display reads THEFTLOCK™. This feature is designed to discourage theft of the radio. It operates by using a secret code in order to disable all the radio functions whenever the battery power is removed.

If the THEFTLOCK™ is active, the THEFTLOCK™ indicator will flash when the ignition is OFF. The THEFTLOCK™ features use is optional. If not used, the system plays normally and the radio is not protected by the feature. If the THEFTLOCK™ is activated, the radio will not operate if stolen.

When THEFTLOCK™ is activated, the radio will display LOC in order to indicate a locked condition anytime the battery power is removed. If the battery loses power for any reason the radio must be unlocked with the secret code before it will operate.

Perform the following steps in order to enter a secret code which will activate the THEFTLOCK™ system. It is recommended that all 9 steps be read before performing the procedure.

Important: In order to avoid restarting the procedure over at Step 4, do not allow more than 15 seconds to elapse between any of the steps or the radio will automatically revert to time.

1. Write down any 3 or 4 digit number from 000--1999 and keep it in a safe place separate from the vehicle.
2. Turn the ignition to the ACC or RUN position.
3. Turn the radio OFF.
4. Press and hold the numbers 1 and 4 buttons together until -- -- -- display. Use the secret code number which has been written down.
5. Press MIN and 000 will appear on the display.
6. Press MIN again in order to make the last 2 digits agree with the code.
7. Press HR in order to make the first 1 or 2 digits agree with the code.
8. Press AM-FM after the secret code that was written down has been confirmed. The display will show REP to indicate steps 5-7 need to be repeated in order to confirm the secret code.
9. Press AM-FM again in order for the display to show SEC ensuring the radio is secure. The indicator by the volume control will begin flashing when the ignition is turned to the OFF position.

Enter the code as follows pausing no more than 15 seconds between steps:

1. Ensure LOC appears when the ignition is turned to the ON position.
2. Press MIN and 000 will appear on the display.
3. Press MIN again in order to ensure the last 2 digits agree with the code.
4. Press HR in order to ensure the first 1 or 2 digits agree with the code.
5. Press AM-FM after the secret code that was written down has been confirmed. The display will show SEC indicating the radio is now operable and secure.

If the wrong code was entered 8 times, INOP will appear on the display. Turn the ignition to the ON position and wait an hour before trying again. The customer will have 3 more chances to enter the correct code before INOP appears.

Enter the secret code as follows pausing no more than 15 seconds between steps:

1. Turn the ignition to the ACC or RUN position.
2. Turn the radio OFF.
3. Press and hold the 1 and 4 buttons together until SEC shows on the display.
4. Press MIN and 000 will appear on the display.
5. Press MIN again in order to make the last 2 digits agree with the code.
6. Press HR in order to make the first 1 or 2 digits agree with the code.
7. Press AM-FM after the secret code that was written down has been confirmed. The display will show -- -- -- indicating the radio is no longer secured.

SEC will appear on the display if the code entered is incorrect. The radio will remain secured until the correct code is entered.

The radio will not turn on and LOC will appear on the display if battery power is given to a secured radio.

Important: Either the customers code or the factory backup code can be used in order to remove the customers code.

Perform the following steps in order to remove the customers code:

1. Turn the ignition to the ACC or RUN position.
2. Turn the radio OFF.

Important: If the display changes to -- -- -- the theft deterrent is deactivated and no code is stored.

3. Press and hold pushbuttons 1 and 4 for approximately 6 seconds until the display changes to SEC.
4. Press the HR button.
5. Set the first 2 digits (0-19) of the code with the HR button.
6. Set the next 2 digits (0-99) of the code with the MIN button.
7. Press the AM-FM button in order to enter the code.
8. The theft deterrent is deactivated when -- -- -- is displayed and then the clock is displayed.

Perform the following steps in order to add the customers code:

1. Turn the ignition to the ACC or RUN position.
2. Turn the radio OFF.

Important: If SEC is displayed the theft deterrent feature is already activated. Remove the old code before entering the new code.

3. Press and hold the pushbuttons 1 and 4 for approximately 6 seconds until the display changes to -- -- --.
4. Press the HR button.
5. Set the first 2 digits (0-19) of the code with the HR button.
6. Set the next 2 digits (0-99) with the MIN button.
7. Press the AM-FM button in order to enter the code.
8. Repeat steps 3-5 when REP then 00 are displayed. This will confirm the following:

•	The customers code

•	Activates the theft deterrent feature

•	After step 5, will display SEC in order to show the theft deterrent feature has been activated.

Important: If -- -- -- is displayed after pressing the AM-FM button, the customers code has not been entered.

9. Anytime the ignition is removed and the THEFTLOCK™ is activated, the THEFTLOCK™ light will flash once every 2 seconds. Anytime the battery power is cycled and the ignition is ON, the display will show LOC. The radio will then need to be unlocked by either the customers code or the factory backup code.

Perform the following steps in order to obtain the radio display code:

Important: In order to display this code, the radio should be in the LOC mode or have SEC displayed before proceeding.

1. Press and hold the pushbuttons 2 and 3 for approximately 6 seconds until the first 3 digits of the display code are displayed.
2. Write the numbers down.
3. Press the AM-FM button. The second 3 digits are displayed.
4. Write the numbers down.

After approximately 5 seconds or if another button is pressed the display returns to LOC. The display code must be unscrambled in order to acquire the factory backup code that unlocks the radio.

In order to acquire the factory backup code call Delco Electronics Corporation and enter the authorized account number along with the display code that has been written down.

In order to change the customers code perform the following:

1. Unlock the radio
2. Ensure there is no customer code currently stored in the radio.

In order to determine whether or not there is a customers code stored:

1. Press and hold the pushbuttons 1 and 4 until the display changes
2. If SEC is displayed, there is a customers code stored. Remove the stored code. Refer to Removing the Customers Code. If -- -- -- is displayed there is no code stored and a new code can be added.

If the customers code is unavailable, refer to the Dealer Communications System for the unlock procedures or call Technical Assistance.