Exterior Trim Molding/Nameplate Replacement Door GTP

Tools Required

J 25070 Heat Gun

Important: Use the tape for protection and alignment marks for alignment of the new emblem/nameplate.




1. Apply tape to the area around the emblem/nameplate.



2. Heat the emblem/nameplate, using a heat gun J 25070 152 mm (6 inches) from the surface.

Apply the heat using a circular motion for about 30 seconds.

3. Peel the emblem/nameplate from the door surface using a flat-bladed tool, being careful not to damage paint.



4. Remove all adhesive from the door surface and the back of the emblem/nameplate using 3M ™scotch brite molding adhesive remover disk 3M™ P/N 07501 or equivalent.
5. Clean the door surface using Varnish Makers and Painters (VMP) naphtha.

1. Mark the tape with the measurements for the barber location of the emblem/nameplate.



2. Warm the door surface with a heat gun J 25070 152 mm (6 inches) from the surface to a minimum of 21° C (70° F).
3. Peel the backing from the front end of the emblem/nameplate.

Do not touch the adhesive backing.

4. Press the emblem/nameplate to the door surface while continuing to remove the backing.
5. Hand roll the emblem/nameplate to the door surface to ensure proper adhesion.
6. Inspect the emblem/nameplate for bonding.

Hand roll loose ends.

7. Remove the tape from the area around the emblem/nameplate.

Exterior Trim Molding/Nameplate Replacement Door SE

Tools Required

J 25070 Heat Gun

Important: Use the tape for protection and alignment marks for alignment of the new emblem/nameplate.

1. Apply tape to the area around the emblem/nameplate.



2. Heat the emblem/nameplate, using a heat gun J 25070 152 mm (6 inches) from the surface.

Apply the heat using a circular motion for about 30 seconds.

3. Peel the emblem/nameplate from the door surface using a flat-bladed tool, being careful not to damage paint.



4. Remove all adhesive from the door surface and the back of the emblem/nameplate using 3M ™scotch brite molding adhesive remover disk 3M™ P/N 07501 or equivalent.
5. Clean the door surface using Varnish Makers and Painters (VMP) naphtha.

1. Mark the tape with the measurements for the barber location of the emblem/nameplate.



2. Warm the door surface with a heat gun J 25070 152 mm (6 inches) from the surface to a minimum of 21° C (70° F).
3. Peel the backing from the front end of the emblem/nameplate.

Do not touch the adhesive backing.

4. Press the emblem/nameplate to the door surface while continuing to remove the backing.
5. Hand roll the emblem/nameplate to the door surface to ensure proper adhesion.
6. Inspect the emblem/nameplate for bonding.

Hand roll loose ends.

7. Remove the tape from the area around the emblem/nameplate.

Exterior Trim Molding/Nameplate Replacement Rear Compartment Lid

Tools Required

J 25070 Heat Gun

Important: Use the tape for protection and alignment marks for alignment of the new emblem/nameplate.

1. Apply tape to the area around the emblem/nameplate.



2. Heat the emblem/nameplate, using a heat gun J 25070 152 mm (6 inches) from the surface.

Apply the heat using a circular motion for about 30 seconds.

3. Peel the emblem/nameplate from the rear compartment lid surface using a flat-bladed tool, being careful not to damage paint.



4. Remove all adhesive from the rear compartment lid surface and the back of the emblem/nameplate using 3M ™scotch brite molding adhesive remover disk 3M™ P/N 07501 or equivalent.
5. Clean the rear compartment lid surface using Varnish Makers and Painters (VMP) naphtha.

1. Mark the tape with the measurements for the barber location of the emblem/nameplate.



2. Warm the rear compartment lid surface with a heat gun J 25070 152 mm (6 inches) from the surface to a minimum of 21° C (70° F).
3. Peel the backing from the front end of the emblem/nameplate.

Do not touch the adhesive backing.

4. Press the emblem/nameplate to the rear compartment lid surface while continuing to remove the backing.
5. Press the emblem/nameplate to the rear compartment lid while continuing to remove the backing.
6. Hand roll the emblem/nameplate to the rear compartment lid to ensure proper adhesion.
7. Inspect the emblem/nameplate for bonding.

Hand roll loose ends.

8. Remove the tape from the area around the emblem/nameplate.