Emblem/Nameplate Replacement Deck - Chevy Emblem
Tools Required
J 25070 Heat Gun
Removal Procedure
- When replacing or repairing an emblem/nameplate do the following:
| 1.1. | Use tape to protect the mounting surface during removal. |
| 1.2. | Use tape for alignment marks for installation of the emblem/nameplate. |
- To remove an emblem/nameplate,
heat the emblem/nameplate using a J 25070
.
Apply heat using a circular motion for about 30 seconds.
Notice: Use a plastic, flat-bladed tool to prevent paint damage when removing
an emblem/name plate.
- Use a plastic, flat-bladed tool to lift or remove the emblem/nameplate
from the panel surface.
Important: If tape is still intact on the molding or panel, do not remove the tape.
Clean the tape and the mating surface with adhesive cleaner. Wipe the tape
and the mating surface with a clean, lint free cloth. If the tape is damaged,
continue with the replacement procedure.
- Apply the adhesive foam tape to the back of the emblem/nameplate and
press the emblem/nameplate in place.
- When replacing, remove all adhesive as follows:
| • | For body panels, use a 3M™ Scotch Brite molding adhesive
remover disk 3M™ P/N 07501 or equivalent. |
| • | For plastic panels, use a lint free cloth and Varnish Makers and
Painters (VMP) naphtha or a (50/50 mixture) by volume of isopropyl alcohol
and water in order to remove the adhesive. |
Installation Procedure
Important: Apply the emblem/nameplate in an environment that is free from dust
or other dirt that could come into contact with the sticky backing. Foreign
material may cause improper adhesion.
- Clean the area where the emblem/nameplate will be installed.
Use a lint free cloth and Varnish Makers and Painters (VMP) naphtha
or a (50/50 mixture) by volume of isopropyl alcohol and water in order to
clean the area.
- Dry the area thoroughly.
- If the location of the
emblem/nameplate has not been marked, apply tape and use the following dimensions:
| • | The emblem (1) is centered below the key cylinder lock. |
| • | It is located 100 mm (3 15/16 in) from the bottom
of the emblem to the bottom edge of the rear compartment lid. |
- Heat the mounting surface to approximately 27-41°C (80-105°F).
- Ensure that the temperature of the emblem/name plate is approximately
29-32°C (85-90°F).
- Remove the protective liner from the back of the emblem/name plate.
- Position the emblem/name plate to the location marks and press
the emblem/name plate to the mounting surface.
- Apply equal pressure along the emblem/name plate in order to uniformly
bond the item to the mounting surface.
- Remove the protective tape from the mounting surface.
Emblem/Nameplate Replacement Z24
Tools Required
J 25070 Heat Gun
Removal Procedure
- When replacing or repairing an emblem/nameplate do the following:
| 1.1. | Use tape to protect the mounting surface during removal. |
| 1.2. | Use tape for alignment marks for installation of the emblem/nameplate. |
- To remove an emblem/nameplate,
heat the emblem/nameplate using a J 25070
.
Apply heat using a circular motion for about 30 seconds.
Notice: Use a plastic, flat-bladed tool to prevent paint damage when removing
an emblem/name plate.
- Use a plastic, flat-bladed tool to lift or remove the emblem/nameplate
from the panel surface.
Important: If tape is still intact on the molding or panel, do not remove the tape.
Clean the tape and the mating surface with adhesive cleaner. Wipe the tape
and the mating surface with a clean, lint free cloth. If the tape is
damaged, continue with the replacement procedure.
- Apply the adhesive foam tape to the back of the emblem/nameplate and
press the emblem/nameplate in place.
- When replacing, remove all adhesive as follows:
| • | For body panels, use a 3M™ Scotch Brite molding adhesive
remover disk 3M™ P/N 07501 or equivalent. |
| • | For plastic panels, use a lint free cloth and Varnish Makers and
Painters (VMP) naphtha or a (50/50 mixture) by volume of isopropyl alcohol
and water in order to remove the adhesive. |
Installation Procedure
Important: Apply the emblem/nameplate in an environment that is free from dust
or other dirt that could come into contact with the sticky backing. Foreign
material may cause improper adhesion.
- Clean the area where the emblem/nameplate will be installed.
Use a lint free cloth and Varnish Makers and Painters (VMP) naphtha
or a (50/50 mixture) by volume of isopropyl alcohol and water in order to
clean the area.
- Dry the area thoroughly.
- If the location of the
emblem/nameplate has not been marked, apply tape and use the following dimensions:
Dimension "A" is 47 mm (1 7/8 in) from the
fender edge to the emblem.
- Heat the mounting surface to approximately 27-41°C (80-105°F).
- Ensure that the temperature of the emblem/name plate is approximately
29-32°C (85-90°F).
- Remove the protective liner from the back of the emblem/name plate.
- Position the emblem/name plate to the location marks and press
the emblem/name plate to the mounting surface.
- Apply equal pressure along the emblem/name plate in order to uniformly
bond the item to the mounting surface.
- Remove the protective tape from the mounting surface.
Emblem/Nameplate Replacement Cavalier LS
Tools Required
J 25070 Heat Gun
Removal Procedure
- When replacing or repairing an emblem/nameplate do the following:
| 1.1. | Use tape to protect the mounting surface during removal. |
| 1.2. | Use tape for alignment marks for installation of the emblem/nameplate. |
- To remove an emblem/nameplate,
heat the emblem/nameplate using a J 25070
.
Apply heat using a circular motion for about 30 seconds.
Notice: Use a plastic, flat-bladed tool to prevent paint damage when removing
an emblem/name plate.
- Use a plastic, flat-bladed tool to lift or remove the emblem/nameplate
from the panel surface.
Important: If tape is still intact on the molding or panel, do not remove the tape.
Clean the tape and the mating surface with adhesive cleaner. Wipe the tape
and the mating surface with a clean, lint free cloth. If the tape is damaged,
continue with the replacement procedure.
- Apply the adhesive foam tape to the back of the emblem/nameplate and
press the emblem/nameplate in place.
- When replacing, remove all adhesive as follows:
| • | For body panels, use a 3M™ Scotch Brite molding adhesive
remover disk 3M™ P/N 07501 or equivalent. |
| • | For plastic panels, use a lint free cloth and Varnish Makers and
Painters (VMP) naphtha or a (50/50 mixture) by volume of isopropyl alcohol
and water in order to remove the adhesive. |
Installation Procedure
Important: Apply the emblem/nameplate in an environment that is free from dust
or other dirt that could come into contact with the sticky backing. Foreign
material may cause improper adhesion.
- Clean the area where the emblem/nameplate will be installed.
Use a lint free cloth and Varnish Makers and Painters (VMP) naphtha
or a (50/50 mixture) by volume of isopropyl alcohol and water in order to
clean the area.
- Dry the area thoroughly.
- If the location of the
emblem/nameplate has not been marked, apply tape and use the following dimensions:
| • | Dimension "A" is 43 mm (1 11/16 inches)
from the left edge of the compartment lid to the nameplate. |
| • | Dimension "B" and "D" are 45 mm
(1 3/4 inches) from the bottom of the compartment lid to the nameplate
bottom. |
| • | Dimension "C" is 235 mm (9 1/4 inches) from
the left edge of the compartment lid to the LS nameplate. |
- Heat the mounting surface to approximately 27-41°C (80-105°F).
- Ensure that the temperature of the emblem/name plate is approximately
29-32°C (85-90°F).
- Remove the protective liner from the back of the emblem/name plate.
- Position the emblem/name plate to the location marks and press
the emblem/name plate to the mounting surface.
- Apply equal pressure along the emblem/name plate in order to uniformly
bond the item to the mounting surface.
- Remove the protective tape from the mounting surface.
Emblem/Nameplate Replacement Chevrolet Nameplate
Tools Required
J 25070 Heat Gun
Removal Procedure
- When replacing or repairing an emblem/nameplate do the following:
| 1.1. | Use tape to protect the mounting surface during removal. |
| 1.2. | Use tape for alignment marks for installation of the emblem/nameplate. |
- To remove an emblem/nameplate,
heat the emblem/nameplate using a J 25070
.
Apply heat using a circular motion for about 30 seconds.
Notice: Use a plastic, flat-bladed tool to prevent paint damage when removing
an emblem/name plate.
- Use a plastic, flat-bladed tool to lift or remove the emblem/nameplate
from the panel surface.
Important: If tape is still intact on the molding or panel, do not remove the tape.
Clean the tape and the mating surface with adhesive cleaner. Wipe the tape
and the mating surface with a clean, lint free cloth. If the tape is damaged,
continue with the replacement procedure.
- Apply the adhesive foam tape to the back of the emblem/nameplate and
press the emblem/nameplate in place.
- When replacing, remove all adhesive as follows:
| • | For body panels, use a 3M™ Scotch Brite molding adhesive
remover disk 3M™ P/N 07501 or equivalent. |
| • | For plastic panels, use a lint free cloth and Varnish Makers and
Painters (VMP) naphtha or a (50/50 mixture) by volume of isopropyl alcohol
and water in order to remove the adhesive. |
Installation Procedure
Important: Apply the emblem/nameplate in an environment that is free from dust
or other dirt that could come into contact with the sticky backing. Foreign
material may cause improper adhesion.
- Clean the area where the emblem/nameplate will be installed.
Use a lint free cloth and Varnish Makers and Painters (VMP) naphtha
or a (50/50 mixture) by volume of isopropyl alcohol and water in order to
clean the area.
- Dry the area thoroughly.
- If the location of the
emblem/nameplate has not been marked, apply tape and use the following dimensions:
| • | Dimension "A" is 41 mm (1 9/16 inches)
the distance from the right edge of the compartment lid to the nameplate. |
| • | Dimension "B" is 15 mm (9/16 inches)
from the bottom of the compartment lid to the nameplate. |
- Heat the mounting surface to approximately 27-41°C (80-105°F).
- Ensure that the temperature of the emblem/name plate is approximately
29-32°C (85-90°F).
- Remove the protective liner from the back of the emblem/name plate.
- Position the emblem/name plate to the location marks and press
the emblem/name plate to the mounting surface.
- Apply equal pressure along the emblem/name plate in order to uniformly
bond the item to the mounting surface.
- Remove the protective tape from the mounting surface.
Emblem/Nameplate Replacement Sunfire GT
Tools Required
J 25070 Heat Gun
Removal Procedure
- When replacing or repairing an emblem/nameplate do the following:
| 1.1. | Use tape to protect the mounting surface during removal. |
| 1.2. | Use tape for alignment marks for installation of the emblem/nameplate. |
- To remove an emblem/nameplate,
heat the emblem/nameplate using a J 25070
.
Apply heat using a circular motion for about 30 seconds.
Notice: Use a plastic, flat-bladed tool to prevent paint damage when removing
an emblem/name plate.
- Use a plastic, flat-bladed tool to lift or remove the emblem/nameplate
from the panel surface.
Important: If tape is still intact on the molding or panel, do not remove the tape.
Clean the tape and the mating surface with adhesive cleaner. Wipe the tape
and the mating surface with a clean, lint free cloth. If the tape is damaged,
continue with the replacement procedure.
- Apply the adhesive foam tape to the back of the emblem/nameplate and
press the emblem/nameplate in place.
- When replacing, remove all adhesive as follows:
| • | For body panels, use a 3M™ Scotch Brite molding adhesive
remover disk 3M™ P/N 07501 or equivalent. |
| • | For plastic panels, use a lint free cloth and Varnish Makers and
Painters (VMP) naphtha or a (50/50 mixture) by volume of isopropyl alcohol
and water in order to remove the adhesive. |
Installation Procedure
Important: Apply the emblem/nameplate in an environment that is free from dust
or other dirt that could come into contact with the sticky backing. Foreign
material may cause improper adhesion.
- Clean the area where the emblem/nameplate will be installed.
Use a lint free cloth and Varnish Makers and Painters (VMP) naphtha
or a (50/50 mixture) by volume of isopropyl alcohol and water in order to
clean the area.
- Dry the area thoroughly.
- If the location of the
emblem/nameplate has not been marked, apply tape and use the following dimensions:
| • | Dimension "A" is 57 mm (2 1/4 in) from
the front edge of the door to the emblem. |
| • | Dimension "B" is 26 mm (1 1/32 in) is
the gap between the Sunfire and the GT. |
| • | Dimension "C" is 39 mm (1 1/2 in) is
the distance from the molding to the emblem. |
- Heat the mounting surface to approximately 27-41°C (80-105°F).
- Ensure that the temperature of the emblem/name plate is approximately
29-32°C (85-90°F).
- Remove the protective liner from the back of the emblem/name plate.
- Position the emblem/name plate to the location marks and press
the emblem/name plate to the mounting surface.
- Apply equal pressure along the emblem/name plate in order to uniformly
bond the item to the mounting surface.
- Remove the protective tape from the mounting surface.
Emblem/Nameplate Replacement Sunfire
Tools Required
J 25070 Heat Gun
Removal Procedure
- When replacing or repairing an emblem/nameplate do the following:
| 1.1. | Use tape to protect the mounting surface during removal. |
| 1.2. | Use tape for alignment marks for installation of the emblem/nameplate. |
- To remove an emblem/nameplate,
heat the emblem/nameplate using a J 25070
.
Apply heat using a circular motion for about 30 seconds.
Notice: Use a plastic, flat-bladed tool to prevent paint damage when removing
an emblem/name plate.
- Use a plastic, flat-bladed tool to lift or remove the emblem/nameplate
from the panel surface.
Important: If tape is still intact on the molding or panel, do not remove the tape.
Clean the tape and the mating surface with adhesive cleaner. Wipe the tape
and the mating surface with a clean, lint free cloth. If the tape is damaged,
continue with the replacement procedure.
- Apply the adhesive foam tape to the back of the emblem/nameplate and
press the emblem/nameplate in place.
- When replacing, remove all adhesive as follows:
| • | For body panels, use a 3M™ Scotch Brite molding adhesive
remover disk 3M™ P/N 07501 or equivalent. |
| • | For plastic panels, use a lint free cloth and Varnish Makers and
Painters (VMP) naphtha or a (50/50 mixture) by volume of isopropyl alcohol
and water in order to remove the adhesive. |
Installation Procedure
Important: Apply the emblem/nameplate in an environment that is free from dust
or other dirt that could come into contact with the sticky backing. Foreign
material may cause improper adhesion.
- Clean the area where the emblem/nameplate will be installed.
Use a lint free cloth and Varnish Makers and Painters (VMP) naphtha
or a (50/50 mixture) by volume of isopropyl alcohol and water in order to
clean the area.
- Dry the area thoroughly.
- If the location of the
emblem/nameplate has not been marked, apply tape and use the following dimensions:
| • | Dimension "A" is 57 mm (2 1/4 in) from
the edge of the front door to the emblem. |
| • | Dimension "B" is 39 mm (1 1/2 in) from
the edge of the door molding to the emblem. |
- Heat the mounting surface to approximately 27-41°C (80-105°F).
- Ensure that the temperature of the emblem/name plate is approximately
29-32°C (85-90°F).
- Remove the protective liner from the back of the emblem/name plate.
- Position the emblem/name plate to the location marks and press
the emblem/name plate to the mounting surface.
- Apply equal pressure along the emblem/name plate in order to uniformly
bond the item to the mounting surface.
- Remove the protective tape from the mounting surface.
Emblem/Nameplate Replacement Cavalier 2.4Z
Tools Required
J 25070 Heat Gun
Removal Procedure
- When replacing or repairing an emblem/nameplate do the following:
| 1.1. | Use tape to protect the mounting surface during removal. |
| 1.2. | Use tape for alignment marks for installation of the emblem/nameplate. |
- To remove an emblem/nameplate,
heat the emblem/nameplate using a J 25070
.
Apply heat using a circular motion for about 30 seconds.
Notice: Use a plastic, flat-bladed tool to prevent paint damage when removing
an emblem/name plate.
- Use a plastic, flat-bladed tool to lift or remove the emblem/nameplate
from the panel surface.
Important: If tape is still intact on the molding or panel, do not remove the tape.
Clean the tape and the mating surface with adhesive cleaner. Wipe the tape
and the mating surface with a clean, lint free cloth. If the tape is damaged,
continue with the replacement procedure.
- Apply the adhesive foam tape to the back of the emblem/nameplate and
press the emblem/nameplate in place.
- When replacing, remove all adhesive as follows:
| • | For body panels, use a 3M™ Scotch Brite molding adhesive
remover disk 3M™ P/N 07501 or equivalent. |
| • | For plastic panels, use a lint free cloth and Varnish Makers and
Painters (VMP) naphtha or a (50/50 mixture) by volume of isopropyl alcohol
and water in order to remove the adhesive. |
Installation Procedure
Important: Apply the emblem/nameplate in an environment that is free from dust
or other dirt that could come into contact with the sticky backing. Foreign
material may cause improper adhesion.
- Clean the area where the emblem/nameplate will be installed.
Use a lint free cloth and Varnish Makers and Painters (VMP) naphtha
or a (50/50 mixture) by volume of isopropyl alcohol and water in order to
clean the area.
- Dry the area thoroughly.
- If the location of the
emblem/nameplate has not been marked, apply tape and use the following dimensions:
| • | Distance "A" is 15 mm (1/16 in) from
the bottom of the deck lid to the emblem. |
| • | Distance "B" is 9 mm (1/32 in) is the
gap between Cavalier and 2.4. |
| • | Distance "C" is 15 mm (1/16 in) from
the bottom of the deck lid to the emblem. |
| • | Distance "D" is 350 mm (13 3/4 in) from
the right edge of the deck lid to the beginning of the emblem. |
- Heat the mounting surface to approximately 27-41°C (80-105°F).
- Ensure that the temperature of the emblem/name plate is approximately
29-32°C (85-90°F).
- Remove the protective liner from the back of the emblem/name plate.
- Position the emblem/name plate to the location marks and press
the emblem/name plate to the mounting surface.
- Apply equal pressure along the emblem/name plate in order to uniformly
bond the item to the mounting surface.
- Remove the protective tape from the mounting surface.
Emblem/Nameplate Replacement Chevy Emblem- Hood
Tools Required
J 25070 Heat Gun
Removal Procedure
- When replacing or repairing an emblem/nameplate do the following:
| 1.1. | Use tape to protect the mounting surface during removal. |
| 1.2. | Use tape for alignment marks for installation of the emblem/nameplate. |
- To remove an emblem/nameplate,
heat the emblem/nameplate using a J 25070
.
Apply heat using a circular motion for about 30 seconds.
Notice: Use a plastic, flat-bladed tool to prevent paint damage when removing
an emblem/name plate.
- Use a plastic, flat-bladed tool to lift or remove the emblem/nameplate
from the panel surface.
Important: If tape is still intact on the molding or panel, do not remove the tape.
Clean the tape and the mating surface with adhesive cleaner. Wipe the tape
and the mating surface with a clean, lint free cloth. If the tape is damaged,
continue with the replacement procedure.
- Apply the adhesive foam tape to the back of the emblem/nameplate and
press the emblem/nameplate in place.
- When replacing, remove all adhesive as follows:
| • | For body panels, use a 3M™ Scotch Brite molding adhesive
remover disk 3M™ P/N 07501 or equivalent. |
| • | For plastic panels, use a lint free cloth and Varnish Makers and
Painters (VMP) naphtha or a (50/50 mixture) by volume of isopropyl alcohol
and water in order to remove the adhesive. |
Installation Procedure
Important: Apply the emblem/nameplate in an environment that is free from dust
or other dirt that could come into contact with the sticky backing. Foreign
material may cause improper adhesion.
- Clean the area where the emblem/nameplate will be installed.
Use a lint free cloth and Varnish Makers and Painters (VMP) naphtha
or a (50/50 mixture) by volume of isopropyl alcohol and water in order to
clean the area.
- Dry the area thoroughly.
- If the location of the
emblem/nameplate has not been marked, apply tape and use the following dimensions:
| • | The emblem (1) is centered on the hood. |
| • | Its located at 27 mm (1 1/16 in) from
the front edge of the hood to the bottom of the emblem/name plate. |
- Heat the mounting surface to approximately 27-41°C (80-105°F).
- Ensure that the temperature of the emblem/name plate is approximately
29-32°C (85-90°F).
- Remove the protective liner from the back of the emblem/name plate.
- Position the emblem/name plate to the location marks and press
the emblem/name plate to the mounting surface.
- Apply equal pressure along the emblem/name plate in order to uniformly
bond the item to the mounting surface.
- Remove the protective tape from the mounting surface.
