DTC P0751 3.8L
Circuit Description
The 1-2 shift solenoid (1-2 SS) valve is supplied with fused ignition voltage. The ground path is controlled by the PCM. When the PCM commands the solenoid OFF, a ground path is not provided and the filtered line pressure that is fed to the solenoid is exhausted. When the PCM commands the solenoid ON, a ground path is provided and the exhaust port is blocked, stopping the exhaust of line pressure.
The PCM identifies a 1-2 SS valve condition by monitoring the commanded gear versus gear ratio. Refer to Shift Solenoid Valve State and Gear Ratio .
If the PCM detects a 2nd gear ratio when 1st gear is commanded and a 3rd gear ratio when 4th gear is commanded, then DTC P0751 sets. DTC P0751 is a type B DTC.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P0751 1-2 Shift Solenoid Valve Performance - No First or Fourth Gear
Conditions for Running the DTC
| • | No VSS DTC P0502 or P0503. |
| • | No ISS sensor DTC P0716 or P0717. |
| • | No TCC system stuck ON DTC P0742. |
| • | No 1-2 SS valve electrical DTC P0753. |
| • | No 2-3 SS valve electrical DTC P0758. |
| • | No TCC PWM solenoid valve DTC P2761. |
| • | The engine is running for greater than 5 seconds and not in fuel shut off. |
| • | The transmission fluid temperature is 20-130°C (68-266°F). |
| • | The transmission ISS is 150 RPM or more. |
| • | The transmission OSS is 300 RPM or more. |
| • | The time since the last gear range change is greater than 1 second. |
Conditions for Setting the DTC
The following conditions both occur twice in one trip:
Condition 1
The PCM commands 1st gear with the TP angle 5 percent or more, the engine torque is between 27 N·m (20 lb ft) and 271 N·m (200 lb ft) and the gear ratio indicates 2nd gear, 1.52:1 to 1.62:1, for 1 second.
Condition 2
The PCM commands 4th gear with the TP angle 10 percent or more, the engine torque is between 41 N·m (30 lb ft) and 271 N·m (200 lb ft) and the gear ratio indicates 3rd gear, 0.95:1 to 1.05:1, for 1 second.
Action Taken When the DTC Sets
| • | The PCM illuminates the malfunction indicator lamp (MIL) during the second consecutive trip in which the Conditions for Setting the DTC are met. |
| • | The PCM commands maximum line pressure. |
| • | The PCM freezes transmission adaptive functions. |
| • | The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze Frame and Failure Records. |
| • | The PCM stores DTC P0751 in PCM history during the second consecutive trip in which the Conditions for Setting the DTC are met. |
Conditions for Clearing the MIL/DTC
| • | The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes. |
| • | A scan tool can clear the MIL/DTC. |
| • | The PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without an emission-related diagnostic fault occurring. |
| • | The PCM cancels the DTC default actions when the ignition switch is OFF long enough in order to power down the PCM. |
Diagnostic Aids
If DTC P0751 is cleared, then will not reset when the vehicle is driven, some of the following conditions may exist:
| • | Fluid contamination |
| • | Plugged fluid circuits |
| • | Restricted fluid circuits |
Test Description
The number below refers to the step number on the diagnostic table.
Step | Action | Value(s) | Yes | No | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information | ||||||||||
2 | Did you perform the Transmission Fluid Checking Procedure? | -- | Go to Step 3 | Go to Transmission Fluid Check | ||||||||||
Important: Before clearing the DTCs, use the scan tool in order to record the Freeze Frame and Failure Records for reference. Using the Clear DTC Information function will erase the stored Freeze Frame and Failure Records from the PCM. Did the gear ratios indicate a 2-2-3-3 shift pattern? | 1st: 2.87:1 to 2.97:1 2nd: 1.52:1 to 1.62:1 3rd: 0.95:1 to 1.05:1 4th: 0.65:1 to 0.75:1 | Go to Step 4 | Go to Diagnostic Aids | |||||||||||
4 | Inspect the 1-2 shift solenoid valve/hydraulic circuit for the following conditions:
Refer to:
Did you find and correct the condition? | -- | Go to Step 5 | -- | ||||||||||
5 | Perform the following procedure in order to verify the repair:
Has the test run and passed? | 1st: 2.87:1 to 2.97:1 2nd: 1.52:1 to 1.62:1 3rd: 0.95:1 to 1.05:1 4th: 0.65:1 to 0.75:1 | Go to Step 6 | Go to Step 2 | ||||||||||
6 | With a scan tool, observe the stored information, capture info and DTC info. Does the scan tool display any DTCs that you have not diagnosed? | -- | Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information | System OK |
DTC P0751 3.6L
Circuit Description
The 1-2 shift solenoid (1-2 SS) valve is supplied with fused ignition voltage. The ground path is controlled by the TCM. When the TCM commands the solenoid OFF, a ground path is not provided and the filtered line pressure that is fed to the solenoid is exhausted. When the TCM commands the solenoid ON, a ground path is provided and the exhaust port is blocked, stopping the exhaust of line pressure.
The TCM identifies a 1-2 SS valve condition by monitoring the commanded gear versus gear ratio. Refer to Shift Solenoid Valve State and Gear Ratio .
If the TCM detects a 2nd gear ratio when 1st gear is commanded and a 3rd gear ratio when 4th gear is commanded, then DTC P0751 sets. DTC P0751 is a type B DTC.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P0751 1-2 Shift Solenoid Valve Performance - No First or Fourth Gear
Conditions for Running the DTC
| • | No TP sensor DTC P0121, P0122 or P0123. |
| • | No ISS sensor DTC P0716 or P0717. |
| • | No VSS DTC P0722 or P0723. |
| • | No TCC system stuck ON DTC P0742. |
| • | No 1-2 SS valve electrical DTC P0973 or P0974. |
| • | No 2-3 SS valve electrical DTC P0976 or P0977. |
| • | No TCC PWM solenoid valve electrical DTC P2763 or P2764. |
| • | The TP angle is 5 percent or more. |
| • | The transmission fluid temperature is between 20°C (68°F) and 130°C (266°F). |
| • | The engine torque is greater than 50 N·m (37lb ft). |
| • | The transmission ISS is 150 RPM or more. |
| • | The transmission OSS is 300 RPM or more. |
| • | The time since the last gear range change is 1 second or more. |
Conditions for Setting the DTC
The following conditions both occur twice in one trip:
Condition 1
The TCM commands 1st gear and the gear ratio indicates 2nd gear, 1.52:1 to 1.62:1, for 1 second.
Condition 2
The TCM commands 4th gear and the gear ratio indicates 3rd gear, 0.95:1 to 1.05:1, for 1 second.
Action Taken When the DTC Sets
| • | The TCM requests the ECM to illuminate the malfunction indicator lamp (MIL) during the second consecutive trip in which the Conditions for Setting the DTC are met. |
| • | The TCM commands maximum line pressure. |
| • | The TCM freezes transmission adaptive functions. |
| • | The TCM records the operating conditions when the Conditions for Setting the DTC are met. The TCM stores this information as Freeze Frame and Failure Records. |
| • | The TCM stores DTC P0751 in TCM history during the second consecutive trip in which the Conditions for Setting the DTC are met. |
Conditions for Clearing the MIL/DTC
| • | The ECM turns OFF the MIL after the third consecutive trip in which the TCM does not send an MIL illumination request. |
| • | A scan tool can clear the MIL/DTC. |
| • | The TCM clears the DTC from TCM history if the vehicle completes 40 warm-up cycles without an emission-related diagnostic fault occurring. |
| • | The TCM cancels the DTC default actions when the ignition switch is OFF long enough in order to power down the TCM. |
Diagnostic Aids
If DTC P0751 is cleared, then will not reset when the vehicle is driven, some of the following conditions may exist:
| • | Fluid contamination |
| • | Plugged fluid circuits |
| • | Restricted fluid circuits |
Test Description
The number below refers to the step number on the diagnostic table.
Step | Action | Value(s) | Yes | No | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information | ||||||||
2 | Did you perform the Transmission Fluid Checking Procedure? | -- | Go to Step 3 | Go to Transmission Fluid Check | ||||||||
Important: Before clearing the DTCs, use the scan tool in order to record the Freeze Frame and Failure Records for reference. Using the Clear Info function will erase the stored Freeze Frame and Failure Records from the TCM. Did the gear ratios indicate a 2-2-3-3 shift pattern? | 1st: 2.87:1 to 2.97:1 2nd: 1.52:1 to 1.62:1 3rd: 0.95:1 to 1.05:1 4th: 0.65:1 to 0.75:1 | Go to Step 4 | Go to Diagnostic Aids | |||||||||
4 | Inspect the 1-2 shift solenoid valve/hydraulic circuit for the following conditions:
Refer to:
Did you find and correct the condition? | -- | Go to Step 5 | -- | ||||||||
5 | Perform the following procedure in order to verify the repair:
Has the test run and passed? | 1st: 2.87:1 to 2.97:1 2nd: 1.52:1 to 1.62:1 3rd: 0.95:1 to 1.05:1 4th: 0.65:1 to 0.75:1 | Go to Step 6 | Go to Step 2 | ||||||||
6 | With a scan tool, observe the stored information, capture info and DTC info. Does the scan tool display any DTCs that you have not diagnosed? | -- | Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information | System OK |
