Circuit Description
The Mass Air Flow (MAF) sensor measures the amount of air which passes through it into the engine during a given time. The PCM uses the mass air flow information to monitor engine operating conditions for fuel delivery calculations. A large quantity of air entering the engine indicates an acceleration or high load situation, while a small quantity of air indicates deceleration or idle. The MAF sensor produces a frequency signal which can be monitored using a scan tool. The frequency will vary within a range of around 2000 Hertz at idle to about 10,000 Hertz at maximum engine load. DTC P0101 will be set if the signal from the MAF sensor does not match a predicted value based on barometric pressure (calculated from MAP at key on) throttle position, and engine RPM.
Conditions for Setting the DTC
| • | The engine is running. |
| • | System voltage is between 9.0V and 16.0V. |
| • | EGR duty cycle is less than 75%. |
| • | MAF signal indicates an airflow significantly higher or lower than a calculated value. |
| • | Above conditions present for at least 12 seconds. |
Action Taken When the DTC Sets
| • | The PCM will illuminate the malfunction indicator lamp (MIL) the first time the malfunction is detected. |
| • | The PCM calculates an airflow value based on idle air control valve position, throttle position, RPM and barometric pressure. |
| • | The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data. |
Conditions for Clearing the MIL/DTC
| • | The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed. |
| • | The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction. |
| • | The DTC can be cleared by using the scan tool. |
Diagnostic Aids
Check for the following conditions:
| • | Skewed or stuck TP sensor. A malfunctioning TP sensor or TP sensor circuit can cause the PCM to incorrectly calculate the predicted mass air flow value. Observe the Throttle Angle displayed on the scan tool with the throttle closed. If the Throttle Angle reading is not 0%, check for the following conditions and repair as necessary: |
| - | Throttle plate sticking or excessive deposits on the throttle plate or in the throttle bore. |
| - | TP sensor signal circuit shorted to voltage. |
| - | Poor connection or high resistance in the TP sensor ground circuit. |
| - | If none of the above conditions are noted and the Throttle Angle reading at closed throttle is not 0%, replace the TP sensor. |
| • | Inspect harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and poor terminal to wire connection. |
| • | Misrouted harness. Inspect the MAF sensor harness to ensure that it is not routed too close to high voltage wires such as spark plug leads. |
| • | Damaged harness. Inspect the wiring harness for damage. If the harness appears to be OK, observe the scan tool while moving connectors and wiring harnesses related to the MAF sensor. A change in the display will indicate the location of the malfunction. |
| • | Plugged intake air duct or dirty air filter element. A wide-open throttle acceleration from a stop should cause the Mass Air Flow displayed on a scan tool to increase from about 4-7 gm/s at idle to 100 gm/s or greater at the time of the 1-2 shift. If not, check for a restriction. |
| • | Skewed or unresponsive MAP sensor. The barometric pressure used to calculate the default Mass Air Flow value is based on the MAP sensor reading. A skewed MAP sensor at key on will cause the BARO reading to be incorrectly calculated. Also, with the engine running, an unresponsive MAP sensor (due to poor vacuum connections, damaged vacuum source, or defective vacuum hose(s), unmetered air into the manifold) will cause inaccurate BARO reading updates during wide-open throttle conditions. Both of these conditions result in a difference between the actual MAF sensor signal and the predicted MAF value (PCM calculated). If a large difference between these two values occurs DTC P0101 will set. This condition may also cause abnormal IAC counts. With the IAC at an incorrect count value, a hard start / no start condition may occur. |
If DTC P0101 cannot be duplicated, the information included in the Fail Records data can be useful in determining vehicle mileage since the DTC was last set. This may assist in determining how often the DTC sets.
Test Description
The numbers below refer to the step numbers on the Diagnostic Table:
-
Only, if sent here from Engine Cranks But Will Not Run, continue to follow diagnostic table even if DTC P0101 has NOT failed this ignition.
-
This step checks the MAP sensor. By disconnecting the MAF sensor, the vehicle is forced into speed density; Speed density is based on the MAP, TP, and engine RPM readings. With a skewed/unresponsive MAP sensor, the speed density calculation is incorrect and vehicle may not start. For further information refer to diagnostic aids.
-
This step checks for skewed or sticking MAP sensor. MAP sensor should respond smoothly and gradually as RPM is increased. Compare MAP sensor of affected vehicle to that of a normally operating vehicle if a large difference is noted replace MAP sensor.
-
Verifies that ignition feed voltage and a good ground are available at the MAF sensor.
Step | Action | Value(s) | Yes | No | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | Was the Powertrain On Board Diagnostic (OBD) System Check performed? | -- | ||||||||||
2 | Is DTC P0121, P1374, P1635 set? | -- | Go to applicable DTC Table, Refer to Powertrain Control Module Diagnosis | |||||||||
Does scan tool indicate DTC P0101 failed this ignition? | -- | Go to Diagnostic Aids | ||||||||||
4 | Important: Do not clear DTC(s)!
Does engine start and continue to run? | -- | ||||||||||
5 |
Does the MAP sensor value change as engine speed increases? | -- | ||||||||||
6 | Refer to Manifold Absolute Pressure Sensor Circuit Check to diagnose MAP sensor circuit. Is the action complete? | -- | -- | |||||||||
7 |
Is the TP sensor parameter within the specified range? | 0-100 % | ||||||||||
8 |
Is the voltage near the specified value? | 5.0 V | ||||||||||
9 | Connect a test light between the MAF sensor ignition feed and ground circuits at the MAF sensor harness connector. Is the test light on? | -- | ||||||||||
10 | Is the voltage less than the specified value? | 4.5 V | ||||||||||
11 |
Does the voltage measure near the specified value? | 0.0 V | ||||||||||
12 | Connect a test light between MAF sensor ignition feed circuit and chassis ground. Is the test light on? | -- | ||||||||||
13 |
Was a poor connection found? | -- | ||||||||||
14 |
Was a problem found? | -- | ||||||||||
15 | Locate and repair the open in the ground circuit to the MAF sensor. Refer to Repair Procedures in Electrical Diagnosis. Is the action complete? | -- | -- | |||||||||
16 | Locate and repair the open, or excessive resistance in the ignition feed circuit to the MAF sensor. Refer to Repair Procedures in Electrical Diagnosis. Is the action complete? | -- | -- | |||||||||
17 | Locate and repair the short to voltage in the MAF signal circuit. Refer to Repair Procedures in Electrical Diagnosis. Is the action complete? | -- | -- | |||||||||
18 | Replace the MAF sensor. Refer to Mass Airflow Sensor Replacement Is the action complete? | -- | -- | |||||||||
19 | Replace the PCM. Important: : The replacement PCM must be programmed. Refer to Powertrain Control Module Replacement/Programming . Is the action complete? | -- | -- | |||||||||
20 |
Does scan tool indicate DTC P0101 failed this ignition? | -- | Repair complete |
