Circuit Description
The 24X reference signal is used to improve idle spark control at low engine speeds. The PCM uses the 24X reference signal to calculate engine RPM and crankshaft position at engine speeds below 1600 RPM. The PCM constantly monitors the number of pulses on the 24X reference circuit and compares the number of 24X reference pulses to the number of 3X reference pulses and CAM signal pulses being received. If the PCM receives an incorrect number of pulses on the 24X reference circuit, DTC P0336 will set and the PCM will use the 3X reference signal circuit for fuel and ignition control. The engine will continue to start and run using the 3X reference and CAM signals only.
Conditions for Running the DTC
The engine is running (3X reference pulses are being received) for a minimum of 3 seconds.
Conditions for Setting the DTC
The ratio of 24X reference pulses to 3X reference pulses received by the PCM is incorrect.
Action Taken When the DTC Sets
| • | The PCM illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The PCM records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the PCM stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the PCM records the operating conditions at the time of the failure. |
| • | The PCM writes the conditions to the Freeze Frame and updates the Failure Records. |
Conditions for Clearing the MIL/DTC
| • | The PCM will turn OFF the malfunction indicator lamp (MIL) during the third consecutive trip in which the diagnostic has run and passed. |
| • | The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction. |
| • | The DTC can be cleared by using a scan tool. |
Diagnostic Aids
DTC P0336 can be caused by secondary components leaking high voltage into the ignition module.
Check for the following conditions:
| • | Incorrect harness routing near secondary ignition components. |
| • | Ignition coil arcing to wiring harness or Ignition Control Module (check ignition coils for cracks, carbon tracking, or other signs of damage). |
| • | Secondary ignition wire(s) arcing to wiring harness. |
An intermittent may be caused by a poor connection, rubbed through wire insulation or a wire broken inside the insulation. Check for:
Important: : Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.
| • | Poor terminal connection. |
| Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to Intermittents and Poor Connections Diagnosis , and Connector Repairs Wiring Systems. |
| • | Damaged harness. |
| Inspect the wiring harness for damage. If the harness appears to be OK, observe the sensor display on the scan tool while moving connectors and wiring harnesses related to the sensor. A change in the sensor display may indicate the location of the fault. Refer to Wiring Repairs in Wiring Systems. |
| • | Inspect the PCM and the engine grounds for clean and secure connections. |
If the DTC is determined to be intermittent, reviewing the Fail Records can be useful in determining when the DTC was last set.
Test Description
Number(s) below refer to the step number(s) on the Diagnostic Table:
-
If sent here from DTC P0327 proceed with DTC P0336 Diagnostic even if P0336 has not failed this ignition.
-
The 24X RPM on the scan tool should change each time the signal circuit is touched.
-
If the fuse blows in the jumper wire, there is a short to ground on the signal circuit.
-
This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM is being replaced, the new PCM must be programmed.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Was the Powertrain On Board Diagnostic (OBD) System Check performed? | -- | ||
Does scan tool indicate DTC P0336 failed this ignition? | -- | Go To Diagnostic Aids | ||
3 | Using the scan tool monitor 24X RPM. Does 24X RPM vary with engine speed up to approximately 1600 RPM? | -- | Go To Diagnostic Aids | |
4 |
Does J 39200 DMM display a voltage near the specified value? | B+ | ||
5 |
Was a problem found? | -- | ||
6 |
Does J 35616-200 test light light? | -- | ||
7 |
Was a problem found? | -- | ||
Does 24X RPM change EACH time the signal circuit is touched? | -- | |||
Did the fuse in the jumper wire blow? | -- | |||
10 | Check signal circuit for an open or a short to voltage, repair as necessary. Refer to Wiring Repairs . Was a problem found? | -- | ||
11 | Check signal circuit for a short to ground, repair as necessary. Refer to Wiring Repairs . Was a problem found? | -- | ||
12 | Check connections at PCM and replace terminals as necessary. Refer to Testing for Continuity , Intermittents and Poor Connections Diagnosis , Repairing Connector Terminals , Connector Repairs . Did any terminals require replacement? | -- | ||
13 |
Important: : Replacement PCM must be reprogrammed. Replace PCM. Refer to Powertrain Control Module Replacement/Programming . Is the action complete? | -- | -- | |
14 | Check connections at 24X CKP sensor and replace terminals as necessary. Refer to Testing for Continuity , Intermittents and Poor Connections Diagnosis , Repairing Connector Terminals , Connector Repairs . Did any terminals require replacement? | -- | ||
15 | Replace 24X CKP sensor. Refer to Crankshaft Position Sensor Replacement . Is action complete? | -- | -- | |
Does scan tool indicate DTC P0336 failed this ignition? | -- | System OK |
