Circuit Description
The automatic transmission fluid pressure (TFP) manual valve position switch consists of six pressure switches (three normally-closed and three normally-open switches). Ignition voltage is applied to each of the switches. By grounding or opening one or more of these switches with fluid pressure from the manual valve, the PCM can detect which gear range is selected.
If the PCM detects an invalid combination of inputs (LOW/HI/LOW or LOW/LOW/LOW), then DTC P1810 sets. If the PCM detects a gear range other than the one indicated, then DTC P1810 sets. DTC P1810 is a type B DTC.
Conditions for Running the DTC
| • | The engine speed is greater than 500 RPM for 5 seconds and not in fuel shut off. |
| • | The system voltage is 9-18 volts. |
Conditions for Setting the DTC
DTC P1810 sets when at least one of the following conditions occurs:
Condition 1
The TFP manual valve position switch indicates an invalid switch combination for 60 seconds.
Condition 2
| • | No VSS DTC P0502 or P0503. |
| • | The vehicle speed is less than 5 km/h (3 mph). |
| • | TFP manual valve position switch indicates REVERSE, D2 or D4 for 7 seconds at engine start up without indicating PARK or NEUTRAL. |
Condition 3
| • | No TP sensor DTC P0121, P0122 or P0123. |
| • | No VSS DTC P0502 or P0503. |
| • | No AT ISS sensor DTC P0716 or P0717. |
| • | No 1-2, 3-4 SS valve DTC P0751 or P0753. |
| • | No 2-3 SS valve DTC P0756 or P0758. |
| • | The TP angle is greater than 9%. |
| • | The vehicle speed is more than 8 km/h (5 mph). |
| • | The engine torque is greater than 70 N·m (50 lb ft) and one of the following conditions occurs: |
| - | The gear ratio indicates REVERSE, D4, D3, D2 or D1 and the TFP manual valve position switch indicates PARK or NEUTRAL for 5 seconds. |
| - | The gear ratio indicates D4, D3, D2 or D1 and the TFP manual valve position switch indicates REVERSE for 7 seconds. |
| - | The gear ratio indicates REVERSE and the TFP manual valve position switch indicates D4, D3, D2 or D1 for 5 seconds. |
Action Taken When the DTC Sets
| • | The PCM illuminates the malfunction indicator lamp (MIL) during the second consecutive trip in which the Conditions for Setting the DTC are met. |
| • | The PCM commands maximum line pressure. |
| • | The PCM freezes shift adapts. |
| • | The PCM assumes D4 for shifting. |
| • | The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze Frame and Failure Records. |
| • | The PCM stores DTC P1810 in PCM history during the second consecutive trip in which the Conditions for Setting the DTC are met. |
Conditions for Clearing the MIL/DTC
| • | The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes. |
| • | A scan tool can clear the MIL/DTC. |
| • | The PCM clears the DTC from the PCM history if the vehicle completes 40 consecutive warm-up cycles without an emission-related diagnostic fault occurring. |
| • | The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down the PCM. |
Diagnostic Aids
| • | Inspect the connectors at the controller, the component and all other circuit connecting points for an intermittent condition. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems. |
| • | Inspect the circuit wiring for an intermittent condition. Refer to Testing for Electrical Intermittents in Wiring Systems. |
| • | Ensure that the transmission linkage from the select lever to the manual valve is adjusted properly. |
| • | If a transmission overhaul was performed, ensure that the transmission fluid is at the proper level. A low fluid condition may set this DTC. |
| • | Inspect the TFP manual valve position switch seals for damage. |
| • | Inspect the TFP manual valve position switch for debris, or loose rivets. |
| • | Refer to the Transmission Fluid Pressure (TFP) Manual Valve Position Switch Logic table for the normal range signals and the invalid combinations. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step tests the indicated range signal to the manual valve range actually selected.
-
This step tests for correct voltage from the PCM to the transmission 20-way connector.
-
This step tests for a short together between signal circuit A and signal circuits B or C.
Step | Action | Value(s) | Yes | No | ||||
|---|---|---|---|---|---|---|---|---|
1 | Did you perform the Powertrain Diagnostic System Check? | -- | Go to Powertrain On Board Diagnostic (OBD) System Check in Engine Controls | |||||
2 | Inspect for proper transmission fluid level. Refer to the Transmission Fluid Check . Did you perform the transmission fluid checking procedure? | -- | -- | |||||
Important: Before clearing the DTCs, use the Scan Tool in order to record the Freeze Frame and Failure Records for reference. Using the Clear Info function will erase the stored Freeze Frame and Failure Records from the PCM. Does each selected transmission range match the transmission range displayed on the Scan Tool ? | -- | Go to Diagnostic Aids | ||||||
4 |
Does the Scan Tool TFP Sw. A/B/C parameter indicate HI for all range signals A, B and C? | -- | ||||||
Refer to Automatic Transmission Inline Harness Connector End View . Does the voltage measure greater than the specified value at all three terminals? | 10 V | |||||||
Connect a fused jumper wire from terminal N of the J 44152 jumper harness (signal circuit A) to ground while monitoring the Scan Tool TFP Sw. A/B/C parameter. When signal circuit A (CKT 1224) is grounded, do any other signal circuits indicate Low? | -- | |||||||
7 | Connect a fused jumper wire from terminal R of the J 44152 jumper harness (signal circuit B) to ground while monitoring the Scan Tool TFP Sw. A/B/C parameter. When signal circuit B (CKT 1225) is grounded, do any other signal circuits indicate Low? | -- | ||||||
8 | Test the signal circuits (CKTs 1224, 1225 and 1226) of the TFP manual valve position switch that did not indicate HI, for a short to ground between the PCM connector and the AT inline 20-way connector. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | ||||||
9 | Test the signal circuits (CKTs 1224, 1225 and 1226) of the TFP manual valve position switch, that did not indicate proper voltage, for an open between the PCM connector and the AT inline 20-way connector. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | ||||||
10 | Test the affected signal circuits of the TFP manual valve position switch for a shorted together condition between the PCM connector C1 or C2 and the AT inline 20-way connector. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | ||||||
11 |
Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find a condition? | -- | ||||||
12 | Replace the AT wiring harness assembly. Refer to Solenoids and Wiring Harness Replacement . Did you complete the replacement? | -- | -- | |||||
13 | Replace the TFP manual valve position switch. Refer to Transmission Fluid Pressure Manual Valve Position Switch Replacement . Did you complete the replacement? | -- | -- | |||||
14 | Replace the PCM. Refer to Powertrain Control Module Replacement/Programming in Engine Controls. Did you complete the replacement? | -- | -- | |||||
15 | Perform the following procedure in order to verify the repair:
Has the test run and passed? | -- | System OK |
