Air Conditioning Compressor Hose Replacement 3.1L

1. Recover the refrigerant. Refer to Refrigerant Recovery and Recharging .
2. Remove the air cleaner and duct assembly. Refer to Air Cleaner Assembly Replacement in 3.1L Engine Controls.
3. Remove the cross vehicle brace, if equipped. Refer to Cross Vehicle Brace Replacement in Body Front End.



4. Remove the A/C compressor hose nut (1) from the condenser.



5. Position the A/C compressor hose aside from the condenser.



6. Remove the A/C compressor hose nut (2) from the accumulator.



7. Position the A/C compressor hose aside from the accumulator.
8. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
9. Remove the lower air deflector. Refer to Radiator Air Baffle Assemblies and Deflectors in Engine Cooling.




Important: Remove and discard all the used O-rings and sealing washers.

10. Remove the bolt and the A/C compressor line at the A/C compressor.
11. Remove the A/C compressor hose assembly.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

Important: Lubricate the new O-rings with mineral base 525 viscosity refrigerant oil.

1. Install the new O-rings onto the A/C compressor hose assembly. Refer to O-Ring Replacement .

Install the new sealing washers onto the A/C compressor hose assembly.




2. Install the A/C compressor hose assembly and bolt at the rear of the A/C compressor.

Tighten
Tighten the A/C compressor hose bolt to 33 N·m (24 lb ft).

3. Install the lower air deflector. Refer to Radiator Air Baffle Assemblies and Deflectors in Engine Cooling.
4. Lower the vehicle.



5. Install the A/C compressor hose to the accumulator.



6. Install the A/C compressor hose nut (2) onto the accumulator.

Tighten
Tighten the A/C compressor hose nut to 16 N·m (12 lb ft).




7. Install the A/C compressor hose to the condenser.



8. Install the A/C compressor hose nut (1).

Tighten
Tighten the A/C compressor hose nut to 16 N·m (12 lb ft).

9. Install the cross vehicle brace, if equipped. Refer to Cross Vehicle Brace Replacement in Body Front End.
10. Install the air cleaner and duct assembly. Refer to Air Cleaner Assembly Replacement in 3.1L Engine Controls.
11. Evacuate and charge the A/C system. Refer to Refrigerant Recovery and Recharging .
12. Leak test the filling(s) of the repaired or the reinstalled component using J 39400 .

Air Conditioning Compressor Hose Replacement 3.8L

1. Recover the refrigerant. Refer to Refrigerant Recovery and Recharging .
2. Remove the air cleaner assembly. Refer to Air Cleaner Assembly Replacement in 3.8L Engine Controls.
3. Remove the cross vehicle brace. Refer to Cross Vehicle Brace Replacement in Body Front End.



4. Remove the A/C compressor hose nut (1) and the hose from the condenser.



5. Remove the A/C compressor hose nut (2) and hose from the accumulator.
6. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
7. Remove the lower air deflector. Refer to Radiator Air Baffle Assemblies and Deflectors in Engine Cooling.



8. Remove the nut and the A/C compressor hose assembly at the A/C compressor.

Important: Remove and discard all the used O-ring and sealing washers.

9. Remove the A/C compressor hose assembly.

1. Install the A/C compressor hose assembly.

Important: The new O-ring seals must be lubricated with mineral base 525 viscosity refrigerant oil.

2. Install the new O-ring seal to the A/C compressor hose assembly. Refer to O-Ring Replacement .

Install the new sealing washers onto the A/C compressor hose assembly.




3. Install the A/C compressor hose assembly to the rear of the A/C compressor.




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

4. Install the A/C compressor hose assembly nut.

Tighten
Tighten the A/C compressor hose nut to 33 N·m (24 lb ft).




5. Install the lower air deflector. Refer to Radiator Air Baffle Assemblies and Deflectors in Engine Cooling.
6. Lower the vehicle.



7. Install the A/C compressor hose nut (2) to the accumulator.

Tighten
Tighten the A/C compressor hose nut to 16 N·m (12 lb  ft).




8. Install the A/C compressor hose and nut to the condenser.

Tighten
Tighten the A/C compressor hose nut to 16  N·m (12 lb  ft).

9. Install the cross vehicle brace. Refer to Cross Vehicle Brace Replacement in Body Front End.
10. Install the air cleaner assembly. Refer to Air Cleaner Assembly Replacement in 3.8L Engine Controls.
11. Evacuate and recharge the A/C system. Refer to Refrigerant Recovery and Recharging .
12. Leak test the fillings of the component using J 39400-A .