GM Service Manual Online
For 1990-2009 cars only

Removal Procedure

The hinges are bolted to the door and body. The door side hinges have elongated holes which allow for some up and down, in and out adjustment. The body side hinges have elongated holes which allow for some fore and aft adjustment.

    Important: In order to minimize door realignment, do not remove both door hinges at the same time. Do each hinge separately and replace any broken hinges first.

  1. Open the door.

  2. Object Number: 315802  Size: MH
  3. Support the door.
  4. Remove the intermediate door hinge bolts.
  5. Remove the hinge spring.

  6. Object Number: 315805  Size: MH
  7. Move the door away from the front pillar as far as the conduit will allow.
  8. Clean the hinge mounting surfaces on the door with a rag and mark the hinge location on the door surface with a grease pencil or other suitable marker.
  9. Remove the bolts from the door side hinge.
  10. Remove the door side hinge.
  11. Important: The body side door hinge has the following 4 attaching bolts:

       • Two 13 mm
       • One TORX®
       • One 10 mm bolt
    A cone attached to the back side of the hinge may fall off and end up in the bottom of the front pillar. This cone is used for assembly purposes only and need not be removed in order to adjust or remove the door hinge strap (body side hinge).

  12. Use a rag in order to clean the hinge mounting surface on the body pillar.

  13. Object Number: 315812  Size: SH
  14. Use a grease pencil or other suitable marker in order to mark the hinge location on the body pillar.
  15. Remove the front fender insulator in order to gain access to the body side hinge bolts (1, 2, 3). Refer to Front Fender Insulator Replacement in Body Front End.

  16. Object Number: 315818  Size: SH

    Important: Do not loosen the cone adjuster bolt (1) (10 mm hex head). The cone may fall down inside the pillar. This may create a rattle situation.

  17. Remove the two 13 mm body side hinge bolts (2).
  18. Remove the one TORX® head body side hinge bolt.
  19. Remove the body side hinge.

Installation Procedure

  1. Align the new door side hinge in position with the old alignment marks.
  2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Apply Locktite® Blue GM P/N 12345382, or Canadian P/N 10953489, or equivalent prior to installing the door side hinge bolts.
  4. Install the door side hinge bolts.
  5. Tighten
    Tighten the door side hinge bolts to 33 N·m (24 lb ft).

  6. Align the new body side hinge in position with the old alignment marks.

  7. Object Number: 315805  Size: MH
  8. Install two 13 mm body side hinge bolts.
  9. Tighten
    Tighten the body side hinge bolts to 33 N·m (24 lb ft).


    Object Number: 315812  Size: SH
  10. Install the TORX® head (1) body side hinge bolt.
  11. Tighten
    Tighten the TORX® head bolt to 10 N·m (89 lb in).

  12. Install the intermediate door hinge bolts.
  13. Tighten
    Tighten the intermediate door hinge bolts to 33 N·m (24 lb ft).

  14. Install the front fender insulator. Refer to Front Fender Insulator Replacement in Body Front End.
  15. Remove the door support.
  16. Adjust the door. Refer to Front Side Door Adjustment .
  17. Close the door.