The intake air temperature (IAT) sensor is a thermistor which measures the temperature of the air entering the engine. The Powertrain Control Module (PCM) applies 5.0 volts through a pull up resistor. When the intake air is cold, the sensor resistance is high and the PCM will monitor a high signal voltage on the IAT sensor signal circuit. As the intake air warm, the sensor resistance becomes lower causing the PCM to monitor a lower voltage. If the PCM detects an excessively low IAT sensor signal voltage (high temperature indicated), DTC P0112 will set.
• | No active ECT, MAF sensor, or VSS DTC present |
• | Engine running for over 10 seconds |
• | Vehicle speed is more than 40 km/h (25 mph). |
• | The IAT signal voltage indicates an intake air temperature more than 135°C (275°F). |
• | The above conditions are present for at least 20 seconds. |
• | The PCM will illuminate the malfunction indicator lamp (MIL) during the second consecutive trip in which the diagnostic test has been run and failed. |
• | The PCM will store conditions which were present when the DTC set as Freeze Frame/Failure Records data. |
• | The PCM will turn OFF the malfunction indicator lamp (MIL) during the third consecutive trip in which the diagnostic has run and passed. |
• | The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction. |
• | The DTC can be cleared by using a scan tool. |
Inspect for the following conditions:
• | Poor connection at the PCM--Inspect harness connectors for: |
• | Backed out terminals |
• | Improper mating |
• | Broken locks |
• | Improperly formed or damaged terminals |
• | Poor terminal to wire connection |
• | Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems. |
• | Damaged harness--Inspect the wiring harness for damage. If the harness appears to be OK, observe the IAT display on the scan tool while moving connectors and wiring harnesses related to the IAT sensor. A change in the IAT display will indicate the location of the fault. Refer to Wiring Repairs in Wiring Systems. |
If DTC P0112 cannot be duplicated, the information included in the Failure Records data can be useful in determining vehicle mileage since the DTC was last set.
The numbers below refer to the step numbers on the diagnostic table.
Verifies that the fault is present.
If DTC P0112 can be repeated only by duplicating the Failure Records conditions. Refer to Temperature vs Resistance table. The table may be used to test the IAT sensor at various temperatures to evaluate the possibility of a shifted sensor that may be shorted above or below a certain temperature. If this is the case, replace the IAT sensor. If the IAT sensor appears to be OK, the fault is intermittent , refer to Diagnostic Aids.
This vehicle is equipped with a PCM which utilizes an electrically erasable programmable read only memory (EEPROM). When the PCM is being replaced, the new PCM must be programmed. Refer to PCM Replacement/Programming.
Step | Action | Values | Yes | No |
---|---|---|---|---|
1 | Did you perform the Powertrain On-Board Diagnostic (OBD) System Check? | -- | ||
Does the scan tool indicate the IAT parameter is more than specified value? | 135°C (275°F) | |||
Does scan tool indicate DTC P0112 failed this ignition? | -- | Go to Diagnostic Aids | ||
4 |
Does the scan tool indicate the IAT parameter is less than the specified value? | -37°C (-34°F) | ||
5 |
Did you find and correct the condition? | -- | ||
6 | Replace the IAT sensor. Refer to Intake Air Temperature Sensor Replacement . Did you complete the replacement? | -- | -- | |
Important: : The replacement PCM must be programmed. Replace the PCM. Refer to Powertrain Control Module Replacement/Programming . Did you complete the replacement? | -- | -- | ||
8 |
Does the DTC reset? | -- | System OK |