GM Service Manual Online
For 1990-2009 cars only

SCALP MOLDING W/ AUXILLARY WINDNOISE CLOSEOUT (NEW PART)

VEHICLES AFFECTED: 86-89 4 DR. "H" AND 85-89 4 DR. "C"

For 1990 model year, a product enhancement was made on the 4-door H and C models to enhance door sealing and reduce the levels of windnoise/windrush. This bulletin provides a service procedure for replacement of these scalp mouldings for the 1990 model and instructions for installation of kits on past models. In the event of a customer windnoise/windrush comment on a 1985-1989 model, Product Service Bulletin 89-2-102 should be followed. If sufficient reduction of windnoise/windrush is not achieved using the items covered in 89-2-102 and windnoise/windrush is from the area between the upper door frame and body opening then the appropriate kit for the past model vehicle may be installed.

BUICK LESABRE AND ELECTRA/PARK AVENUES FRONT DOOR SCALP MOULDING WITH AUXILIARY WINDNOISE CLOSEOUT SEAL

SERVICE INSTALLATION INSTRUCTION:

1. Apply soap solution to cover complete perimeter of outer edge of stationary door frame. Completely cover black scalp moulding clip at lower front edge of door frame.

2. Insert scalp moulding into beltline opening at the front of the door frame but DO NOT snap or slide onto the black scalp moulding clip. Refer to Figure 1.

3 and 4. Position front door window frame scalp moulding assembly to front door. Starting at the upper rear corner, engage over outer edges of the top leg and upper rear vertical leg of the door frame simultaneously. (Refer to Figure 3) Once corner on frame, push scalp moulding as far forward as possible on horizontal leg of header.

5 - 9. Engage moulding over the outer edge of the stationary door frame and snap moulding onto retainer clips on the inner edge of stationary door frame, as shown in Figure 2 working in the order depicted in Figure 3.

10. Engage moulding over the INNER edge of the black clip then snap over the OUTER edge.

11 - 12. Engage moulding over the outer edge of the stationary door frame and snap moulding onto retainer clips on the inner edge of stationary door frame as shown in Figure 2 working in the order depicted in Figure 3.

IMPORTANT: Cross section of correctly installed moulding, refer to Figure 4.

Kent-Moore Installation Tool No. J-38714 will be available

OLDSMOBILE C/H FRONT DOOR SCALP MOULDING WITH AUXILIARY WINDNOISE CLOSEOUT SEAL

SERVICE INSTALLATION INSTRUCTIONS

1. Apply soap solution to cover complete perimeter of outer edge of stationary door frame. Completely cover black scalp moulding clip at lower front edge of door frame.

2. Slide front door window frame scalp moulding assembly three quarters of the way down over the black scalp moulding clip at the lower front of the door.

3 and 4. Position front door window frame scalp moulding assembly to front door. Starting at the upper rear corner, engage over outer edges of the top leg and upper rear vertical leg of the door frame simultaneously. Refer to Figure 3. Once corner on frame, push scalp moulding as far forward as possible on horizontal leg of header.

5 - 11. Engage moulding over the outer edge of the stationary door frame and snap moulding onto retainer clips on the inner edge of stationary door frame, as shown in Figure 2 working in the order depicted in Figure 3.

IMPORTANT: Cross section of correctly installed moulding as shown in Figure 4.

Kent-Moore Installation Tool #J-38714 will be available

C/H REAR DOOR SCALP MOULDING WITH AUXILIARY WINDNOISE CLOSEOUT SEAL

SERVICE INSTALLATION INSTRUCTIONS:

1. Apply soap solution to cover complete perimeter of outer edge of stationary door frame.

2 and 3. Position rear door window frame scalp moulding assembly to rear door and starting at upper front corner, engage over outer edges of top leg and upper front vertical leg of door frame simultaneously, as shown in Figure 4. Once corner on frame, push scalp moulding as far forward as possible on horizontal leg of header.

4 - 10. Engage moulding over the outer edge of the stationary door frame and snap moulding onto retainer clips on the inner edge of stationary door frame, as shown in Figure 2 working in the order depicted in Figure 5.

Clean area of ALL excess soap. This would be general information for both doors.

IMPORTANT: Cross section of correctly installed moulding as shown in Figure 4.

PARTS INFORMATION:

The following parts are supplied in kit form for 1985-89 model years.

Oldsmobile #25557063 - Chrome 3CW69, 3CX69 #25557064 - Black 3CW69

Pontiac #25557065 - Met. Grey 2HX69 LE, 2H269-B57 #25557066 - Black 2H269XB57

Oldsmobile #25557067 - Chrome 3HA69

Buick-Pontiac #25557068 - Chrome 4HA69, 2HX69LE

Buick #25557069 - Chrome 4CX69, 4CV69

IMPORTANT: For current model application, the individual mouldings are serviced separately and are currently available.

Use most applicable Labour Operation and Time from the Canadian Labour Time Guide.


Object Number: 95203  Size: SH


Object Number: 95222  Size: SH


Object Number: 88759  Size: MF


Object Number: 86465  Size: LF


Object Number: 89514  Size: MF

General Motors bulletins are intended for use by professional technicians, not a "do-it-yourselfer". They are written to inform those technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions and know-how to do a job properly and safely. If a condition is described, do not assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See a General Motors dealer servicing your brand of General Motors vehicle for information on whether your vehicle may benefit from the information.