Diagnostic Instructions
DTC Descriptors
DTC P2762: Torque Converter Clutch (TCC) Pressure Control Solenoid System Performance
DTC P2763: Torque Converter Clutch (TCC) Pressure Control Solenoid Control Circuit High Voltage
DTC P2764: Torque Converter Clutch (TCC) Pressure Control Solenoid Control Circuit Low Voltage
Circuit/System Description
The torque converter clutch (TCC) pressure control solenoid is part of the control solenoid (w/body and TCM) valve assembly and is not serviced separately. The TCM supplies 12 volts to the TCC pressure control solenoid through the high side
driver 2 circuit. The TCM controls the TCC solenoid through the TCC solenoid control circuit. The normally low TCC pressure control solenoid flows fluid to the TCC when commanded ON and exhausts fluid when commanded OFF. The TCC solenoid regulates the
transmission fluid pressure to the TCC.
Conditions for Running the DTC
P2762
| • | DTC P2762 has not failed this ignition cycle. |
| • | The engine speed is greater than 500 RPM for 5 seconds or greater. |
| • | The ignition voltage is between 8.6-19.0 volts. |
P2763
| • | DTC P2763 has not failed this ignition cycle. |
| • | The engine speed is greater than 500 RPM for 5 seconds or greater. |
| • | The ignition voltage is between 8.6 volts and 19.0 volts. |
| • | The high side driver is enabled. |
P2764
| • | DTC P2764 has not failed this ignition cycle. |
| • | The engine speed is greater than 500 RPM for 5 seconds or greater. |
| • | The ignition voltage is between 8.6-19.0 volts. |
| • | The high side driver is enabled. |
Conditions for Setting the DTC
P2762
The TCM detects an invalid voltage in the TCC pressure control solenoid circuit for 4.4 seconds or greater in a 5.0 second sample.
P2763
The TCM detects high voltage on the TCC pressure control solenoid control circuit for 4.4 seconds or greater in a 5.0 second sample.
P2764
The TCM detects low voltage on the TCC pressure control solenoid control circuit for 4.4 seconds or greater in a 5.0 second sample.
Action Taken When the DTC Sets
P2762
DTC P2762 is a Type C DTC.
P2763 and P2764
| • | DTCs P2763 and P2764 are Type A DTCs. |
| • | The TCM commands maximum line pressure. |
| • | The TCM freezes transmission adaptive functions. |
| • | The TCM forces High Side Drive 1 and 2 OFF. |
Conditions for Clearing the DIC/DTC
| • | DTC P2762 is a Type C DTC. |
| • | DTCs P2763 and P2764 are Type A DTCs. |
Reference Information
Description and Operation
Transmission General Description
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References for scan tool information
Circuit Verification
- Ensure the transmission fluid temperature is between 50-80°C (122-176°F).
- Perform the
Control Solenoid Valve and Transmission Control Module Assembly Cleaning to dislodge debris and free up the valves.
- Operate the vehicle in 2nd gear long enough to ensure at least a 3°C (5°F) rise in TCM temperature, then operate the vehicle to ensure TCC engagement for 5 seconds.
- Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.
| ⇒ | If the DTC does not reset, replace the control solenoid (w/body and TCM) valve assembly. |
Repair Instructions
Important:
Perform the
Diagnostic Repair Verification after completing the diagnostic procedure.
