Diagnostic Instructions
DTC Descriptors
DTC P0741: Torque Converter Clutch (TCC) - Stuck Off
DTC P0742: Torque Converter Clutch (TCC) - Stuck On
Circuit/System Description
The torque converter clutch (TCC) pressure control (PC) solenoid is part of the control solenoid (w/body and TCM) valve assembly and is not serviced separately. The shift solenoid (SS) 1 supplies transmission fluid to the TCC PC
solenoid when commanded OFF. The TCC PC solenoid regulates transmission fluid through the TCC regulator valve in the lower valve body and the TCC control valve in the pump, to the TCC when commanded ON and exhausts fluid when commanded OFF. When the TCC
is applied, the engine is coupled directly to the transmission.
Conditions for Running the DTC
P0741
| • | No ISS DTCs P0716 or P0717. |
| • | No OSS DTCs P0722 or P0723. |
| • | No TCC DTCs P2762, P2763, or P2764. |
| • | DTC P0741 has not passed this key ON. |
| • | The ignition voltage is between 8.6 volts and 19.0 volts. |
| • | The transmission fluid temperature (TFT) is 20-130°C (68-266°F). |
| • | The throttle position is greater than 8 percent. |
| • | The engine torque is greater than 50 N·m (36 lb ft). |
| • | The 2nd gear ratio is between 2.67-3.07. |
| • | The 3rd gear ratio is between 1.71-1.97. |
| • | The 4th gear ratio is between 1.32-1.51. |
| • | The 5th gear is between 0.93-1.07. |
| • | The 6th gear is between 0.69-0.79. |
| • | The TCC is commanded ON. |
P0742
| • | No ISS DTCs P0716 or P0717. |
| • | No OSS DTCs P0722 or P0723. |
| • | No shift valve 1 DTC P1751. |
| • | No TCC DTCs P2762, P2763, or P2764. |
| • | DTC P0742 has not passed this key ON. |
| • | The ignition voltage is between 8.6 volts and 19.0 volts. |
| • | The transmission fluid temperature (TFT) is 20-130°C (68-266°F). |
| • | The calc. throttle position is greater than 8 percent. |
| • | The engine torque is greater than 80 N·m (59 lb ft). |
| • | The engine speed is greater than 500 RPM. |
| • | The vehicle speed is greater than 16 km/h (10 mph). |
| • | The gear ratio is between 0.69-1.97. |
| • | The commanded gear is 2nd. |
| • | The solenoid A is enabled. |
| • | The TCC is commanded OFF. |
Conditions for Setting the DTC
P0741
| • | The TCC Pressure is greater than 800 Kpa for 5 seconds. |
| • | The TCM detects TCC slip greater than 50 RPM for 6 seconds when the TCC is commanded ON three times during the same ignition cycle. |
P0742
The TCM detects the TCC slip between -20 and +30 RPM for 2.5 seconds or greater when the TCC is commanded OFF six times during the same ignition cycle.
Action Taken When the DTC Sets
| • | DTCs P0741 and P0742 are Type B DTCs. |
| • | Inhibit high gear in Hot Mode. |
| • | The TCM freezes transmission adaptive functions. |
Conditions for Clearing the DIC/DTC
DTCs P0741 and P0742 are Type B DTCs.
Reference Information
Schematic Reference
Automatic Transmission Controls Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Transmission General Description
Electrical Information Reference
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References for scan tool information
Special Tools
DT-47825
Control Solenoid Test Plate
Circuit/System Verification
- Perform the
Transmission Fluid Check to verify correct fluid level and condition. The transmission fluid level should be within the crosshatch band and the transmission fluid should be red or dark brown.
- Engine idling at operating temperature. Attempt to clean or free up a potential sticking valve with the scan tool Service Cleaning Procedure. Refer to
Control Solenoid Valve and Transmission Control Module Assembly Cleaning for further instructions.
- Operate the vehicle in drive with the throttle position greater than 8 percent and ensure TCC is commanded ON and OFF a minimum of 6 times. The DTCs should not set.
- Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
- Ignition OFF, remove the control solenoid (w/body and TCM) valve assembly.
- Install the
DT-47825
to the control solenoid (w/body and TCM) valve assembly. Refer to
Control Solenoid Valve and Transmission Control Module Assembly Solenoid Performance Test for detailed instructions.
- Perform the
Control Solenoid Valve and Transmission Control Module Assembly Solenoid Performance Test. A pressure change should occur.
| ⇒ | If a pressure change does not occur, replace the control solenoid (w/body and TCM) valve assembly. |
- Inspect for the following conditions and repair/replace as necessary:
| • | Lower control valve body for a stuck valve, debris or damage |
| • | TCC control valve in the pump for a stuck valve, debris or damage |
| • | Torque converter assembly for damage or discoloration |
Repair Instructions
Important:
Perform the
Diagnostic Repair Verification after completing the diagnostic procedure.
