GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC B2705 02: Gearshift Unlock Circuit Short to Ground

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

Shift Lock Control Solenoid Ground

--

1

--

--

Shift Lock Control Solenoid Voltage

B2705 02 or 1

1

2

--

1. Shift lever will not move from PARK with the brake pedal pressed.

2. Shift lever will move from PARK without pressing on the brake pedal.

Circuit/System Description

The body control module (BCM) controls the automatic transmission shift lock control solenoid by providing a battery positive voltage to the solenoid. The BCM controls the voltage supply circuit to the automatic transmission shift lock control solenoid.

Conditions for Running the DTC

    • The ignition switch is in the ON position.
    • The brake pedal is pressed.
    • The transmission is in the PARK position.

Conditions for Setting the DTC

The DTC sets if there is a short to ground in the automatic transmission shift lock control solenoid control circuit.

Action Taken When the DTC Sets

The BCM will not attempt to enable the voltage supply circuit of the automatic transmission shift lock control solenoid until the next key cycle.

Conditions for Clearing the DTC

    • A current DTC B2705 will clear when the malfunction is no longer present and the ignition switch is cycled.
    • All BCM history codes will clear after 100 ignition cycles with no current codes active during the 100 ignition cycles.

Reference Information

Schematic Reference

Shift Lock Control Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Automatic Transmission Shift Lock Control Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

  1. Ignition ON, clear the DTC. Observe the scan tool BCM Brake Applied Output Signal parameter. The parameter should change from ON to OFF when the brake pedal is depressed.
  2. If the parameter does not change, refer to Stop Lamps Malfunction .
  3. Ignition ON, while pressing the brake pedal, observe the scan tool Brake Applied Output Signal parameter. The reading should be ON with the brake pedal pressed.

Circuit/System Testing

  1. Ignition OFF, disconnect the harness connector at the shift lock control solenoid.
  2. Ignition OFF, test for less than 1 ohm between the ground circuit terminal A and ground.
  3. If greater than the specified range, test the ground circuit for an open/high resistance.
  4. Install a test lamp between the ground circuit terminal A and the control circuit terminal B.
  5. Ignition ON, command the scan tool BCM Brake To Shift Control output control ON and OFF. The test lamp should turn ON and OFF as commanded.
  6. If the test lamp is always ON, test the control circuit for short to voltage. If the circuit tests normal, replace the BCM.
    If the test lamp is always OFF, test the control circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.
  7. If all circuits test normal, replace the shift lock control solenoid.

Component Testing

  1. Install a 10 A fused jumper wire between the control circuit terminal A and 12 volts. Install a jumper wire between the ground circuit terminal B and ground.
  2. Verify the solenoid turns ON and OFF.
  3. If the function does not perform as specified, replace the shift lock actuator.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Automatic Transmission Shift Lock Control Actuator Replacement
    •  Control Module References for BCM replacement, setup, and programming