GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Buick 🢒 2009 🢒 Enclave - AWD 🢒 Body Repair 🢒 Collision Repair 🢒 Rail Replacement - Rear Section

Removal Procedure

    Warning: Refer to Approved Equipment for Collision Repair Warning in the Preface section.


    Object Number: 1834963 Size: SH
  1. Disable the Supplemental Inflatable Restraint (SIR) System. Refer to SIR Disabling and Enabling.
  2. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
  3. Remove all related panels and components.
  4. Repair as much of the damage as possible to factory specifications. Refer to Dimensions - Body.
  5. Note the location and remove the sealers and anti-corrosion materials from the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair.

    6. Object Number: 1834964 Size: SH

    Note: Do not damage floor panel.

  6. Cut the panel where sectioning is to be performed.

    7. Object Number: 1835159 Size: SH
  7. Locate and drill out all factory welds. Note the number and location of welds for installations of service part.

    8. Object Number: 1834965 Size: SH
  8. Remove the damaged rail from the vehicle.

Installation Procedure

    Object Number: 1835609 Size: SH
  1. Cut the replacement rail section in corresponding locations to fit the original panel. The sectioning joint should be trimmed to allow 1½ times the metal thickness at the sectioning joint.

    2. Object Number: 1835611 Size: SH
  2. Create a 100 mm (4 in) backing plate (A) from the unused portion of the service part. Trim the backing plate, as necessary to fit behind the sectioning joint where there is no reinforcement.

    3. Object Number: 1834966 Size: SH
  3. Drill 8 mm (5/16 in) plug weld holes along the sectioning cut on the remaining original part. Locate these holes 13 mm (½ in) from the edge and spaced 40 mm (1½ in) apart.

    4. Object Number: 1835613 Size: SH

    Note: In any area damaged beyond recognition, or if structural weld-thru adhesive is present, space the plug weld holes 40 mm (1½ in) apart.

  4. Drill 8 mm (5/16 in) plug weld holes in the service part, as necessary in the locations noted from the original panel and along the sectioning cut.

    5. Object Number: 1835615 Size: SH

    Note: If the location of the original plug weld holes cannot be determined, or if structural weld-thru adhesive is present, space the plug weld holes every 40 mm (1½ in) apart.

  5. Prepare all attachment surfaces as necessary.
  6. Apply GM-Approved Weld-Thru Coating or equivalent to all mating surfaces. Refer to Anti-Corrosion Treatment and Repair.
  7. Fit the backing plate halfway into the sectioning joint, clamp and plug weld to the vehicle.

    8. Object Number: 1835622 Size: SH
  8. Position the rail.

    9. Object Number: 1835623 Size: SH
  9. Plug weld accordingly.

    10. Note: To create a solid weld with minimum heat distortion make 25 mm (1 in) stitch welds along the seam with 25 mm (1 in) gaps between them. Then go back and complete the stitch weld.

  10. Stitch the weld sectioning joint.
  11. Clean and prepare all welded surfaces.
  12. Apply the sealers and anti-corrosion materials to the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair.
  13. Paint the repair area. Refer to Basecoat/Clearcoat Paint Systems.
  14. Install all related panels and components.
  15. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
  16. Enable the SIR system. Refer to SIR Disabling and Enabling.