Circuit Description
The heated oxygen sensor (HO2S) heater reduces the time required for the oxygen sensor (O2S) to reach operating temperature and maintains the operating temperature during extended idle periods. When the ignition is turned to the ON position, ignition voltage is supplied directly to the sensor heater. The engine control module (ECM) controls the heater operation by first modulating the control circuit to ground when the sensors are cold. This prevents the possibility of thermal shock to the sensor, from condensation build-up on the sensor, by controlling the sensors rate of heating. After a predetermined amount of time, the ECM commands the heaters ON continuously. Once the sensor reaches operating temperature, the ECM may modulate the heater control circuit to ground, to maintain a desired temperature.
The ECM controls the heater by grounding the control circuit with a solid state device called a driver. The driver is equipped with a feedback circuit that is pulled-up to voltage. The ECM can determine if the control circuit is open, shorted to ground, or shorted to a voltage by monitoring the feedback voltage.
The ECM calculates the HO2S heater element resistance based on the internal HO2S sensing element. If the ECM detects that the HO2S heater element resistance is too high, this DTC sets.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P0141 HO2S Heater Performance Sensor 2
Conditions for Running the DTC
| • | Before the ECM can report DTC P0141 failed, DTCs P0036, P0037, and P0038 must run and pass. |
| • | DTCs P0137, P0138, P0140, P2232, P2270, and P2271 are not set. |
| • | The engine is operating. |
| • | The ignition 1 voltage is between 10.5-18 volts. |
| • | The ECM internal sensing element resistance test is enabled. |
| • | The fuel system is not in a decel fuel shut-off. |
| • | The intake air temperature (IAT) is more than -10°C (14°F). |
| • | If the engine is operating and then the ignition is turned OFF, the engine must be OFF for at least 2 minutes before the next start-up for the diagnostic to run. |
| • | The calculated exhaust temperature is between 360-500°C (680-932°F). |
| • | DTC P0141 runs continuously once the above conditions are met for more than 100 seconds. |
Conditions for Setting the DTC
| • | The ECM detects that the HO2S internal resistance is not within the expected range. |
| • | The condition exists for more than 4 seconds. |
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 4 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Diagnostic Aids
The following table illustrates the ECM connector locations:
ECM Connector Location | |
|---|---|
C2 | C1 |
Front of Vehicle | |
| • | Use the J 35616-A/BT-8637 Connector Test Adapter Kit for any test that requires probing the ECM harness connector or a component harness connector. |
| • | The rear HO2S will not go into closed loop when the engine is idling. Once the HO2S are at operating temperature, and the vehicle is moving, the rear HO2S will go into closed loop. |
| • | For an intermittent condition, refer to Intermittent Conditions . |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step determines if the condition exists.
-
This step tests the signal circuit of the HO2S for high resistance.
Step | Action | Values | Yes | No |
|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Engine Control Module Connector End Views or Engine Controls Connector End Views | ||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |
Did DTC P0141 fail this ignition? | -- | Go to Step 4 | Go to Step 3 | |
3 |
Did the DTC fail this ignition? | -- | Go to Step 4 | Go to Diagnostic Aids |
Is the voltage less than the specified value? | 25 mV | Go to Step 5 | Go to Step 8 | |
5 |
Is the voltage less than the specified value? | 25 mV | Go to Step 6 | Go to Step 9 |
6 |
Important: Use the J 35616-200 Test Lamp Kit for this test. If the J 35616-200 is not available, use a test lamp that measures more than 20 ohms. Is the voltage at the specified value? | B+ | Go to Step 7 | Go to Step 12 |
7 |
Is the resistance less than the specified value? | 5 ohms | Go to Step 10 | Go to Step 13 |
8 | Test the signal circuit of the HO2S for an open or for high resistance. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 11 |
9 | Test the low reference circuit of the HO2S for an open or for high resistance. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 11 |
10 | Test for shorted terminals and poor connections at the HO2S. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 14 |
11 | Test for shorted terminals and poor connections at the ECM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 15 |
12 | Repair the open or the high resistance in the ignition 1 voltage circuit of the HO2S heater . Refer to Wiring Repairs . Did you complete the repair? | -- | Go to Step 16 | -- |
13 | Repair the open or the high resistance in the heater control circuit of the HO2S. Refer to Wiring Repairs . Did you complete the repair? | -- | Go to Step 16 | -- |
14 | Replace the HO2S. Refer to Heated Oxygen Sensor 2 Replacement . Did you complete the replacement? | -- | Go to Step 16 | -- |
15 | Replace the ECM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 16 | -- |
16 |
Did the DTC fail this ignition? | -- | Go to Step 2 | Go to Step 17 |
17 | Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | -- | System OK | |
