Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 |
Does the indicator stay on or flash continuously? | -- | Refer to PASS- Key®II Diagnostic System Check Cell 133 in Electrical Diagnosis | |
2 | Perform the battery load test. Refer to Battery Load Test . Did the battery check as OK? | -- | ||
3 | Check the battery cables and connections. Are the battery cables and connections OK? | -- | ||
4 |
Is the measured voltage greater than the specified value? | 8 V | ||
5 |
Is the measured voltage greater than the specified value? | 8 V | ||
6 |
Does the test lamp light? | -- | ||
7 |
Does the test lamp light? | -- | ||
8 |
Does the test lamp light? | -- | ||
9 |
Is the measured voltage greater than the specified value? | 8 V | ||
10 | Check for an open in CKT 575 (YEL). Is CKT 575 OK? | -- | ||
11 | Replace the battery. Refer to Battery . Is the battery replacement complete? | -- | -- | |
12 | Repair the battery cable connections or replace battery cables as needed. Refer to Battery Cable . Is the battery cable repair complete? | -- | -- | |
13 |
Is the starter replacement complete? | -- | -- | |
14 | Repair the open or short to ground in CKT 6 (PPL). Refer to Electrical Repairs Cell 5 in Electrical Diagnosis. Is the circuit repair complete? | -- | -- | |
15 | Backprobe with a test lamp between Battery Positive Voltage (B+) and the PNP switch connector C1 terminal E, CKT 625 (YEL/BLK). Does the test lamp light? | -- | ||
16 | Replace the park/neutral position (PNP) switch. Refer to 4T60-E Transaxle On-Vehicle Service or 4T65-E Transaxle On-Vehicle Service . Is the park/neutral position (PNP) switch replacement complete? | -- | -- | |
17 | Check for an open in CKT 625 (YEL/BLK). Is CKT 625 OK? | -- | ||
18 | Replace the Pass-Key®II Decoder Module. Refer to PASS-Key®II Module Replacement in Theft Deterrent Systems. Is the Pass-Key®II Decoder Module replacement complete? | -- | -- | |
19 | Check the AIRBAG/VATS Fuse 2E in the I/P Fuse Block for an open. Is the AIRBAG/VATS Fuse 2E OK? | -- | ||
20 |
Is the circuit repair and fuse replacement complete? | -- | -- | |
21 | Repair the open in CKT 806 (PPL). Refer to Electrical Repairs Cell 5 in Electrical Diagnosis. Is the circuit repair complete? | -- | -- | |
22 |
Is the measured voltage greater than the specified value? | 8 V | ||
23 | Repair the open in CKT 5 (YEL) between S217 and the I/P Fuse Block. Refer to Electrical Repairs Cell 5 in Electrical Diagnosis. Is the circuit repair complete? | -- | -- | |
24 | Backprobe with a test lamp between the ignition switch connector C202 terminal D5, CKT 1342 (RED). Does the test lamp light? | -- | ||
25 | Check for an open in CKT 5 (YEL) between S217 and the ignition switch connector C202. Is the CKT 5 OK? | -- | ||
26 | Replace the ignition switch. Refer to Ignition & Dimmer Switch Assembly in Tilt Strg Col Unit Repair (SIR). Is the ignition switch replacement complete? | -- | -- | |
27 | Check the IGN SW Fuse in the RH MaxiFuse® Block for an open. Is the IGN SW Fuse OK? | -- | ||
28 |
Is the circuit repair and fuse replacement complete? | -- | -- | |
29 | Repair the open in CKT 1342 (RED). Refer to Electrical Repairs Cell 5 in Electrical Diagnosis. Is the circuit repair complete? | -- | -- | |
30 | Repair the open in CKT 5 (YEL) between S217 and the starter enable relay. Refer to Electrical Repairs Cell 5 in Electrical Diagnosis. Is the circuit repair complete? | -- | -- | |
31 | Replace the starter enable relay. Refer to Starter Enable (Theft Deterrent) Relay in Instrument Panel, Gauges, and Console. Is the starter enable relay replacement complete? | -- | -- | |
32 | Repair the suspect circuit. Refer to Electrical Repairs Cell 5 in Electrical Diagnosis. Is the circuit repair complete? | -- | -- |
