DTC P1870 Transmission Component Slipping. Buick LeSabre 1997

Go to Step 5

Inspect the following components for the indicated condition:

•	Is the TCC solenoid checkball stuck?

Refer to Converter Clutch Apply Rough, Slips, or Shudders

•	Does the TCC apply valve fit poorly?

•	Is the converter clutch valve stuck?

•	Is the regulator valve stuck?

Refer to Converter Clutch Apply Rough, Slips, or Shudders

•	Is the TCC PWM solenoid checkball stuck?

•	Is the turbine shaft 0-ring seal cut or missing?

Refer to Converter Clutch Apply Rough, Slips, or Shudders

•	Is the torque converter fiber material worn or glazed?

Refer to Converter Clutch Apply Rough, Slips, or Shudders

Did you find and correct a problem?

Inspect the following components for the indicated condition:

•	Is the 3-4 shift valve stuck?

Refer to No 3-4 Shift

•	Are the 4th clutch fiber plates burned or damaged?

Refer to No 3-4 Shift

•	Are the 4th clutch piston seals cut or rolled?

Refer to No 3-4 Shift

•	Is the driven sprocket support ring rolled or twisted, or is a sleeve worn in the 2nd clutch housing?

Refer to First Gear Only

Refer to Harsh or Soft 1-2 Shift Feel

Refer to Shudder 1-2 Shift

Refer to No 2-3 Shift

•	Are the 2nd clutch fiber plates burned or damaged?

Refer to First Gear Only

Refer to Shudder 1-2 Shift

•	Are the 2nd clutch piston seals cut or rolled?

Refer to First Gear Only

Refer to Shudder 1-2 Shift

Did you find and correct a problem?

Go to Step 7

Inspect the following components for the indicated condition:

•	Are the input shaft seals cut or rolled

Refer to No Drive in Drive Range

Refer to No 2-3 Shift

•	Are the 3rd clutch fiber plates burned or damaged?

Refer to No 2-3 Shift

•	Are the 3rd clutch piston seals cut or rolled?

Refer to No 2-3 Shift

•	Is the forward band burned or damaged?

Refer to No Drive in Drive Range

•	Is the forward band apply piston oil seal cut or rolled?

Refer to Delayed Engagement

Refer to Slips in Drive

Refer to No Drive in Drive Range

Did you find and correct a problem?

Begin the diagnosis again. Go to Step 1

In order to verify your repair, perform the following procedure:

Select DTC.
Select Clear Info.
Operate the vehicle under the following conditions:

•	The transmission fluid temperature is 20-130°C (68-266°F).

•	The throttle position is 8.5-35%.

•	The engine speed is 800-1500 RPM.

•	The vehicle is not in fuel shut off.

•	The gear range is D4.

•	The gear is not 1st.

•	The Speed Ratio is 0.70-0.98.

•	The vehicle speed is 56-120 km/h (35-75).

•	The engine torque is 70-230 N·m (50-170 lb. ft).

•	The PCM commands the TCC ON and at maximum apply for more than 5 seconds.

•	The TCC slip speed is -20 to +50 RPM for more than 5 seconds.

Select Specific DTC. Enter DTC P1864.

Has the test run and passed?

System OK

DTC P1870 Transmission Component Slipping All Other Applications

Table 1:	Thumbnail, DTC P1870 (Modified 4T60-E Range Ref.) for use with gc28119
Table 2:	DTC P1870 Transmission Component Slipping

OBD II Symbol Description Notice
Automatic Transmission Controls Schematics
Automatic Transmission Components

Thumbnail, DTC P1870 (Modified 4T60-E Range Ref.) for use with gc28119

Range	Gear	1-2 Solenoid Valve	2-3 Solenoid Valve	4th Clutch	2nd Clutch	3rd Clutch	3rd Sprag Clutch	1/2 Support Roller Clutch	Forward Band
Overdrive	2nd	OFF	ON	--	Applied	--	--	Holding	Applied
	3rd	OFF	OFF	--	Applied	Applied	Holding	Overrun	Applied
	4th	ON	OFF	Applied	Applied	Applied, but not effective	Overrun	Overrun	Applied
ON = the solenoid valve is energized. OFF = the solenoid valve is de-energized

Circuit Description

The Powertrain Control Module (PCM) monitors the Torque Converter Clutch (TCC) slip by calculating the difference between the engine speed and the transmission output shaft speed.

If the PCM detects an excessive amount of slip when the TCC is engaged, then DTC P1870 sets. DTC P1870 is a type B DTC.

Conditions for Setting the DTC

•	No TP DTCs P0122 or P0123

•	No VSS DTCs P0502 or P0503.

•	No 1-2 solenoid performance DTC P0751

•	No 1-2 solenoid electrical DTC P0753

•	No 2-3 solenoid performance DTC P0756

•	No 2-3 solenoid electrical DTC P0758

•	No TCC PWM solenoid electrical DTC P1860

•	No TCC solenoid electrical DTC P0740

•	The engine speed is 800-5000 RPM.

•	Not in fuel shut off

•	The throttle angle is 8-35%.

•	The transmission is not in first gear.

•	The transmission gear range is D4.

•	The transmission fluid temperature is 20-130°C (68-266°F).

•	The engine torque is 70-230 N·m (50-170 ft lbs.).

•	The speed ratio is 0.70-1.05.

•	The vehicle speed is 56-120 km/h (35-75 mph).

•	The TCC is commanded ON and at maximum apply for 5 seconds.

•	The TCC slip is 200-1500 RPM for 8 seconds.

•	The above conditions must occur three times with the TCC commanded OFF between each occurrence.

Action Taken When the DTC Sets

•	The PCM inhibits TCC operation.

•	The PCM inhibits 4th gear, if the transmission is in the hot mode.

•	The PCM illuminates the Malfunction Indicator Lamp (MIL) after 2 consecutive ignition cycles with a failure reported.

Conditions for Clearing the MIL/DTC

•	The PCM turns OFF the MIL after three consecutive ignition cycles without a failure reported.

•	A scan tool can clear the DTC from the PCM history. The PCM clears the DTC from the PCM history if the vehicle completes 40 warm-up cycles without a failure reported.

•	The PCM cancels the DTC default actions when the fault no longer exists and the ignition is OFF long enough in order to power down the PCM.

Diagnostic Aids

•	Ensure that the vehicle's final drive ratio matches the PCM's calibration.

•	Ensure that the transmission will shift through all four gears with the gear select lever in the D4 range.

Test Description

The numbers below refer to the step numbers on the diagnostic chart.

This Step inspects the modulator assembly, which could cause P1870 to set.

These are the components that could cause P1870 to set.

DTC P1870 Transmission Component Slipping

Step

Action

Value(s)

Yes

Was the Powertrain On-Board Diagnostic (OBD) System Check performed?

Go to Step 2

Go to Powertrain On Board Diagnostic (OBD) System Check

Have you performed the fluid checking procedure?

Go to Step 3

Go to Transmission Fluid Check

Install the Scan Tool ®.
With the engine OFF, turn the ignition switch to the RUN position.

Record the DTC Freeze Frame and Failure Records.
Select TCC Slip Speed.
Drive the vehicle with the gear select lever in D4 range. Ensure the TCC engages.

Is the TCC slip speed greater than the specified value?

200 RPM

Go to Step 4

Go to Diagnostic Aids

Inspect the modulator assembly. Refer to Line Pressure Check .
Repair the item if necessary.

Did you find and correct a problem?

Go to Step 5

Inspect the following components for the indicated condition:

•	Is the TCC solenoid checkball stuck?

Refer to Converter Clutch Apply Rough, Slips, or Shudders

•	Does the TCC apply valve fit poorly?

•	Is the converter clutch valve stuck?

•	Is the regulator valve stuck?

Refer to Converter Clutch Apply Rough, Slips, or Shudders

•	Is the TCC PWM solenoid checkball stuck?

•	Is the turbine shaft 0-ring seal cut or missing?

Refer to Converter Clutch Apply Rough, Slips, or Shudders

•	Is the torque converter fiber material worn or glazed?

Refer to Converter Clutch Apply Rough, Slips, or Shudders

Did you find and correct a problem?

Inspect the following components for the indicated condition:

•	Is the 3-4 shift valve stuck?

Refer to No 3-4 Shift

•	Are the 4th clutch fiber plates burned or damaged?

Refer to No 3-4 Shift

•	Are the 4th clutch piston seals cut or rolled?

Refer to No 3-4 Shift

•	Is the driven sprocket support ring rolled or twisted, or is a sleeve worn in the 2nd clutch housing?

Refer to First Gear Only

Refer to Harsh or Soft 1-2 Shift Feel

Refer to Shudder 1-2 Shift

Refer to No 2-3 Shift

•	Are the 2nd clutch fiber plates burned or damaged?

Refer to First Gear Only

Refer to Shudder 1-2 Shift

•	Are the 2nd clutch piston seals cut or rolled?

Refer to First Gear Only

Refer to Shudder 1-2 Shift

Did you find and correct a problem?

Go to Step 7

Inspect the following components for the indicated condition:

•	Are the input shaft seals cut or rolled

Refer to No Drive in Drive Range

Refer to No 2-3 Shift

•	Are the 3rd clutch fiber plates burned or damaged?

Refer to No 2-3 Shift

•	Are the 3rd clutch piston seals cut or rolled?

Refer to No 2-3 Shift

•	Is the forward band burned or damaged?

Refer to No Drive in Drive Range

•	Is the forward band apply piston oil seal cut or rolled?

Refer to Delayed Engagement

Refer to Slips in Drive

Refer to No Drive in Drive Range

Did you find and correct a problem?