Circuit Description
The 2-3 shift solenoid valve (2-3 SS Valve) controls the fluid acting on the 2-3 shift valves. The solenoid is a normally-open exhaust valve. In combination with the 1-2 Shift Solenoid Valve (1-2 SS Valve), the 2-3 SS Valve allows four different shifting combinations. The solenoid is attached to the control valve body within the transmission. Circuit 339/839 supplies ignition voltage to the 2-3 SS Valve. The PCM controls the solenoid by providing the ground path through circuit 1223.
If the PCM detects a continuous open or short to ground in the 2-3 SS Valve circuit or in the 2-3 SS Valve, then DTC P0758 sets. DTC P0758 is a type A DTC.
Conditions for Setting the DTC
| • | The ignition is ON. |
| • | The system voltage is 9-16 volts. |
| • | The engine speed is greater than 500 RPM for 5 seconds, and not in fuel shut off. |
| • | The PCM commands the solenoid ON and the voltage remains high (B+). |
| • | The PCM commands the solenoid OFF and the voltage remains low (0 volts). |
| • | Al conditions are met for 5 seconds. |
Action Taken When the DTC Sets
| • | The PCM illuminates the Malfunction Indicator Lamp (MIL). |
| • | The PCM commands 3rd gear. |
| • | The PCM commands maximum line pressure. |
| • | The PCM disables shift adapts. |
| • | The PCM inhibits Torque Converter Clutch. |
Conditions for Clearing the MIL/DTC
| • | The PCM turns OFF the MIL after three consecutive trips without a failure reported. |
| • | A scan tool can clear the DTC from the PCM history. The PCM clears the DTC from the PCM history if the vehicle completes 40 warm-up cycles without a failure reported. |
| • | The PCM cancels the DTC default actions when the fault no longer exists and the ignition is OFF long enough in order to power down the PCM. |
Diagnostic Aids
| • | Inspect the wiring for poor electrical connections at the PCM. Inspect the wiring for poor electrical connections at the transmission 20-way connector. Inspect the wiring for poor electrical connections at the 2-3 Shift Solenoid Valve connector. Look for the following conditions: |
| - | A bent terminal |
| - | A backed out terminal |
| - | A damaged terminal |
| - | Poor terminal tension |
| - | A chafed wire |
| - | Moisture Intrusion |
| - | A broken wire inside the insulation |
| • | When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change. |
| • | Ensure that the scan tool commanded gear has correct solenoid states and ratio. Refer to Shift Solenoid Valve State and Gear Ratio table. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step isolates the fault between the engine harness and the transmission harness.
-
This step verifies that circuit 1223 is not open or shorted to power.
-
This step verifies that the 2-3 solenoid is not shorted across its windings nor increased its resistance.
-
Because of the harsh conditions inside the transmission, repairing the A/T Wiring Harness is not acceptable. You must replace the A/T Wiring Harness.
Step | Action | Value(s) | Yes | No | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | Were you sent here from the Powertrain On-Board Diagnostic (OBD) System Check? | -- | Go to Powertrain On Board Diagnostic (OBD) System Check in Engine Controls | |||||||||||||
2 |
Important: Before clearing the DTCs, use the Scan Tool in order to record the Freeze Frame and Failure Records for reference. The Clear Info function will erase the data. Are DTCs P0753 and P1860 set? | -- | ||||||||||||||
3 |
Refer to General Electrical Diagnosis in Wiring Systems. Did you find and correct a condition? | -- | ||||||||||||||
4 | Repair the short to ground in circuit 339 (PNK)/839 (RED). Refer to Wiring Repairs in Wiring Systems. Did you find and correct a condition? | -- | -- | |||||||||||||
5 | Repair open in circuit 339 (PNK)/839 (RED). Refer to Wiring Repairs in Wiring Systems. Did you find and correct a condition? | -- | -- | |||||||||||||
Important: Additional DTCs will set. Is the test lamp ON? | -- | |||||||||||||||
7 | Inspect circuit 1223 (YEL/BLK) for a short to ground. Refer to General Electrical Diagnosis in Wiring Systems. Did you find and correct a condition? | -- | ||||||||||||||
Does the test lamp cycle ON and OFF as you commanded? | -- | |||||||||||||||
9 | Inspect circuit 1223 (YEL/BLK) for an open. Refer to General Electrical Diagnosis in Wiring Systems. Did you find and correct a condition? | -- | ||||||||||||||
10 | Is the test lamp always OFF? | -- | -- | |||||||||||||
11 | Inspect circuit 1223 (YEL/BLK) for a short to power. Refer to General Electrical Diagnosis in Wiring Systems. Did you find and correct a condition? | -- | ||||||||||||||
Refer to Automatic Transmission Inline Harness Connector End View . Is the measured resistance within the specified range? | 19-24 ohms at 20°C (68°F) 24-31 ohms at 88°C (190°F) | |||||||||||||||
13 | Is the resistance greater than the specified value? | 100 ohms | ||||||||||||||
14 |
Refer to General Electrical Diagnosis in Wiring Systems. Did you find a condition? | -- | ||||||||||||||
15 | Connect a J 39200 DMM from terminal B of the J 39775 Jumper Harness to ground. Is the measured resistance less than the specified value? | 100 ohms | ||||||||||||||
16 | Inspect automatic transmission wiring harness circuit 1223 (YEL) for a short to ground. Did you find a condition? | -- | -- | |||||||||||||
17 | Replace the 2-3 Shift Solenoid. Refer to 2-3 Shift Solenoid Valve Replacement . Is the replacement complete? | -- | -- | |||||||||||||
18 | Replace the PCM. Refer to Powertrain Control Module Replacement/Programming in Engine Controls. Is the replacement complete? | -- | -- | |||||||||||||
Replace the Automatic Transmission Wiring Harness. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? | -- | -- | ||||||||||||||
20 | In order to verify your repair, perform the following procedure:
Has the test run and passed? | -- | System OK |
