Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Lighting Systems Diagnostic System Check? | -- | Go to Step 2 | |
2 |
Does the scan tool parameter display ON? | -- | Go to Step 3 | Go to Step 10 |
3 | With a scan tool, observe the overhead lamps output parameter in the rear integration module (RIM) data list . Does the scan tool parameter display ON? | -- | Go to Step 4 | Go to Step 21 |
4 | Probe the interior lamp relay output circuit with a test lamp connected to a good ground. Does the test lamp illuminate? | -- | Go to Step 16 | Go to Step 5 |
5 |
Does the test lamp illuminate? | -- | Go to Step 6 | Go to Step 18 |
6 | Connect a test lamp between the coil side power feed circuit of the interior lamp relay and a good ground. Does the test lamp illuminate? | -- | Go to Step 7 | Go to Step 19 |
7 |
Does the test lamp illuminate? | -- | Go to Step 8 | Go to Step 20 |
8 | Inspect for poor connections at the interior lamp relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 23 | Go to Step 9 |
9 | Replace the interior lamp relay. Refer to Wiring Repairs in Wiring Systems. Did you complete the replacement? | -- | Go to Step 23 | -- |
10 |
Does the test lamp turn ON and OFF with the switch? | -- | ||
11 | Test the interior lamp switch input circuit of high resistance or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 23 | |
12 | Inspect for poor connections at the headlamp switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 23 | |
13 | Replace headlamp switch. Refer to Headlamp Switch Replacement . Did you complete the replacement? | -- | Go to Step 23 | -- |
14 | Inspect for poor connections at the CCP (w/C67) or the IPM (w/CJ2). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 23 | Go to Step 15 |
15 | Replace the CCP (w/C67) or the IPM (w/CJ2). Refer to Control Assembly Replacement in HVAC or Instrument Panel Module Replacement in Body Control System. Did you complete the replacement? | -- | Go to Step 23 | -- |
16 | Test the interior lamp relay output circuit for high resistance or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 23 | Go to Step 17 |
17 | Test the interior lamp controlled ground circuit for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 23 | Go to Step 18 |
18 | Repair the open in the interior lamp relay switch side power feed circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 23 | Go to Step 19 |
19 | Repair the open in the interior lamp relay coil side power feed circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 23 | -- |
20 | Test the interior lamp relay control circuit for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 23 | Go to Step 21 |
21 | Inspect for poor connections at the RIM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 23 | Go to Step 22 |
22 | Replace the RIM. Refer to Rear Integration Body Control Module Replacement in Body Control System. Did you complete the replacement? | -- | Go to Step 23 | -- |
23 | Operate the system in order to verify the repair. Did you find and correct the condition? | -- | System OK | Go to Step 2 |
