GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Buick 🢒 2001 🢒 LeSabre 🢒 Brakes 🢒 Hydraulic Brakes 🢒 Brake Pedal Assembly Replacement

Removal Procedure
  1. Remove the IP carrier assembly, to gain access to the brake pedal assembly to cowl mounting nuts. Refer to Instrument Panel Carrier Replacement in Instrument Panel, Gauges and Console.
  2. Remove the accelerator cable from the brake pedal bracket assembly. Refer to Accelerator Control Cable Replacement in Engine Controls - 3.8L.
  3. Remove the steering column support mounting nuts. Refer to Steering Column Replacement in Steering Wheel Column -Tilt.
  4. Lower the steering column and support.

    5. Object Number: 106373 Size: SH
  5. Disconnect the electrical connectors (3) from the stoplamp/ABS/shift lock switch (2).
  6. Remove the stoplamp/ABS/shift lock switch. Refer to Stop Lamp Switch Replacement .
  7. Disconnect the electrical connector from the TCC/cruise control release switch.
  8. Remove the TCC/cruise control release switch from the brake pedal assembly. Refer to Cruise Control Release Switch Replacement in Cruise Control.

    9. Object Number: 695567 Size: SH
  9. Remove the vacuum brake pushrod retainer (3) from the brake pedal clevis pin.
  10. Remove the foam spacer (2) from the brake pedal clevis pin.
  11. Disconnect the vacuum brake booster pushrod (1) from the brake pedal.

    12. Object Number: 287894 Size: SH
  12. Remove the brake pedal assembly mounting nuts (2, 3) from the booster studs (2, 3).
  13. Remove the brake pedal assembly mounting to cowl stud nuts (1).
  14. Remove the brake pedal assembly.

Installation Procedure

    Object Number: 287894 Size: SH
  1. Install the brake pedal assembly into position on the brake booster and cowl studs.

    2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  2. Install the brake pedal assembly to brake booster mounting nuts (2, 3).

    3. Tighten
    Tighten the brake pedal assembly to booster stud mounting nuts (2, 3) to 23 N·m (17 lb ft).

  3. Install the brake pedal assembly to cowl stud mounting nuts.

    4. Tighten
    Tighten the brake pedal assembly to cowl mounting nuts (1) to 16 N·m (12 lb ft).

  4. Apply a small amount of lubricant, GM P/N 12346293 or equivalent, to the clevis pin of the brake pedal.

    5. Object Number: 695567 Size: SH
  5. Connect the vacuum brake booster pushrod (1) to the brake pedal clevis pin.
  6. Install the foam spacer (2) to the brake pedal clevis pin.
  7. Install the retainer (3) to the brake pedal clevis pin.
  8. Install the TCC/cruise control release switch to the brake pedal assembly. Refer to Cruise Control Release Switch Replacement in Cruise Control.
  9. Install the stoplamp/ABS/shift lock switch. Refer to Stop Lamp Switch Replacement .

    10. Object Number: 106373 Size: SH
  10. Connect the electrical connectors (3) to the stoplamp/ABS/shift lock switch (2).
  11. Connect the electrical connector to the TCC/cruise control release switch.
  12. Install the steering column. Refer to Steering Column Replacement in Steering Wheel Column -Tilt.
  13. Install the accelerator cable to the brake pedal bracket assembly. Refer to Accelerator Control Cable Replacement in Engine Controls - 3.8L.
  14. Install the IP assembly. Refer to Instrument Panel Carrier Replacement in Instrument Panel, Gauges and Console.