GM Service Manual Online
For 1990-2009 cars only

Electrical Load Management

Electrical load management is designed to maintain battery voltage and covers more than load-shed. The dash integration module (DIM) will request increases in idle speed from the powertrain control module (PCM), when the vehicle is in park or neutral, as well as turn off loads in order to manage the electrical system and preserve the vehicle electrical power availability. The DIM calculates the battery temperature, voltage and charging rate at all times while the engine is running.

The DIM calculates the battery temperature by factoring in:

    • the current intake manifold air temperature compared to the last temperature recorded when the ignition switch was turned OFF
    • the current battery voltage compared to the last battery voltage recorded when the ignition switch was turned OFF
    • the length of time since the last battery temperature calculation

If the calculated battery temperature is below -15°C (5°F), the PMM institutes steps to control the load.

The DIM calculates the voltage of the battery by making constant voltage measurements and using the measurements to calculate the true battery voltage. If the DIM detects a low voltage, the DIM institutes steps to control the load.

The DIM calculates the net charge rate on the electrical system by making constant voltage measurements and using the measurements to calculate the charge rate in amp/hours. If the DIM detects a negative charge rate, equal to a discharge from the battery, the PMM institutes steps to control the load.

The DIM will either request an increase in the engine idle speed from the (PCM, VCM, ECM) or the DIM will turn off loads, called the load-shed function, in order to preserve the vehicle electrical system operation. The criteria used by the DIM to regulate this electrical load management are outlined below:

Function

Battery Temperature Calculation

Battery Voltage Calculation

Amp-hour Calculation

Action Taken

Idle Boost 1 Start

Less Than -15°C (5°F)

--

--

First level Idle boost requested

Idle Boost 1 Start

--

--

Battery has a net loss of 0.6  AH

First level Idle boost requested

Idle Boost 1 End

Greater Than -15°C (5°F)

Battery has a net loss of less than 0.2  AH

First level Idle boost request cancelled

Idle Boost 1 End

--

14.0 V

Battery has a net loss of less than 0.2  AH

First level Idle boost request cancelled

Load Shed 1 Start

--

--

Battery has a net loss of 1.6  AH

Controlled outputs cycled OFF for 20% of their cycle

Load Shed 1 End

--

--

Battery has a net loss of less than 0.8 AH

Clear Load Shed 1

Idle Boost 2 Start

--

--

Battery has a net loss of 5.0  AH

Second level Idle boost requested

Idle Boost 2 End

--

--

Battery has a net loss of less than 2.0 AH

Second level Idle boost request cancelled

Idle Boost 3 Start

--

--

Battery has a net loss of 10.0 AH

Third level Idle boost requested

Idle Boost 3 Start

--

--

Third level Idle boost requested

Idle Boost 3 End

--

Greater Than 13.0 V

Battery has a net loss of less than 6.0  AH

Third level Idle boost request cancelled

Load Shed 2 Start

--

Less Than 10.9 V

Battery has a net loss of 20.0  AH

--

Controlled outputs cycled OFF for 100% of their cycle, Battery Indicator or Battery Saver Indicator ON request sent

Load Shed 2 End

--

Greater Than 13.0 V

battery has a net loss of less than 10.5 AH

Clear Load Shed 2

Each load management function, either idle boost or load-shed, is discrete. No two functions are implemented at the same time.

During each load management function, the DIM checks the battery temperature, battery voltage and amp-hour calculations and determines if the DIM should implement a different power management function.

The highest loads on the electrical system are the resistance load of heating elements. The DIM controls the heating elements in the outside rear view mirrors, the rear window and the heated seats, either directly or by sending messages to any module controlling power to these devices.

The second highest load on the electrical system are the blowers used in the HVAC system. The DIM will send messages to the HVAC system controller that will result in reducing the blower operation on vehicles equipped with automatic HVAC systems.

Idle Boost Functions

The DIM sends a serial data request to the (PCM, ECM) to increase the idle speed. The (PCM, ECM) then adjusts the idle speed by using a special program and idle speed ramp calculations in order to prevent driveability and safety concerns. The idle speed boost and cancel function will vary from vehicle to vehicle and from one moment to another on the same vehicle. This happens because the (PCM, ECM) responds to changes in the inputs from the sensors used to control the powertrain.

Load Shed Level

Affected Systems

Action Taken

Load-Shed Level 0

No systems affected

Normal operation

Load-Shed Level 1

Heated Outside Rear View Mirrors, Heated Rear Window/Rear Window Defrost, Heated Seats

Cycled at 80% duty cycle, OFF for 4 of every 20 second cycle. Indicator and timer not affected.

Message Center, Instrument Cluster

No messages or indicators are displayed. Data (DPID) indicating that the Load-Shed 1 was entered is stored and may be accessed with a scan tool. DPID will reset after 40 ignition switch cycles with no repeated load-shed 1 action or with a battery disconnection.

Load-Shed Level 2

Heated Outside Rear View Mirrors, Heated Rear Window/Rear Window Defrost, Heated Seats

Turned OFF. Indicator and timer are not affected. The indicators and timers are controlled by the RIM. The operator must turn ON system when load-shed level is exited. System will not respond to operator input until current load-shed level is exited. This system will respond to only one Load-Shed Level 2 command per ignition switch cycle.

Message Center, Instrument Cluster

"Battery Saver Action" message is displayed. Charge indicator is illuminated. Data (DPID) indicating that the Load-Shed Level 2 was entered is stored and may be accessed with a scan tool. DPID will reset after 40 ignition switch cycles with no repeated Load-Shed 2 actions or with a battery disconnection.